Listening To The Radio - AEG KRC 4338 Instruction Manual

English
26
• For the installation the cupboard must fulfil the following
conditions:
Thickness of the cupboard floor
between 16 mm and 20 mm.
• The wall mounting of the cupboard must be stable and
anchored firmly in the wall with at least 2 screws.
• Important! Do not install the device above a cooker!
• When installing the device it must be ensured that there
is a power socket within reach.
• The mains socket must be within easy reach, so that the
plug can be quickly removed in an emergency.
• Important! Do not connect the device to the mains
power supply until after installation!
• The device cannot be installed under cupboards under
which there is a lighting strip.
• For mounting, you may need the following supplies: A
drill with 6 mm drill bit, pilot drill or nail, Allen key, tape
measure, adhesive tape, scissors, safety goggles.
Supplied mounting accessories
4 Screws
4 Spacers
1 Drilling template
CAUTION:
• Please adhere to the dimensions stated in the installa-
tion instructions.
• You should use only the installation accessories sup-
plied.
Installation
• Tape the template firmly down to the shelf with adhesive
tape. With the help of a gimlet or nail pierce the crosses
at the attachment points and use it to mark the holes.
• Remove the template and drill the holes into the wall
cupboard.
• Insert the spacer into the holes provided on the device.
NOTE:
Sufficient ventilation is only guaranteed with a spacer.
• Countersink the screws into the holes in the cupboard.
• Using the 4 screws and the spacers, attach the kitchen
radio to the bottom of the cupboard.
• Tighten the screws hand-tight with an Allen key.
CAUTION:
Use a wrench and not an electric screwdriver.
Start-up of the device / Introduction
• Read the operating instructions thoroughly before the
start-up!
• Make sure that the device is adequately ventilated!
• If applicable, remove the protective film from the display.
Power supply
Insert the plug into a properly installed 230 V, 50 Hz power
socket. 0:00 will appear on the display. Please ensure that the
mains voltage corresponds to the information on the type
plate.
Switching the Device on/off (4)
Switch the device to the standby mode with the STANDBY
button (the time is displayed). If this button is pressed once
more, the device switches on again.
Setting of the Clock (24 h) (in Standby Mode)
1. Hold down the TIME SET button (5) for approx. 3 sec-
onds. The hour indicator will flash on the display.
2. Adjust the setting with the SKIP+/SKIP- buttons (12/13).
3. Press the TIME SET button for confirmation. The minute
indicator will flash on the display.
4. Adjust the setting with the SKIP+/SKIP- buttons (12/13).
5. Save the time setting by pressing the TIME SET button
again.
Adjusting the volume
Use the VOL+/VOL- buttons (14) to adjust the volume.
Display brightness
Use the SNOOZE/DIMMER button (15) to adjust the bright-
ness of the display and the LCD clock.

Listening to the radio

NOTE:
The preset stations will be lost if the power is interrupted.
Scanning stations
• Tune the desired stations with the SKIP+ (12) and SKIP-
(13) buttons. When holding down either of the buttons,
the device will start scanning until the next radio station is
found. The display will show the respective frequency.
• If there is interference on the received station, try to
improve the reception by rotating, winding or unwinding
the wire antenna.
Presetting radio stations
The device can preset up to 20 radio stations. To preset a
station, follow the steps below:
1. Search for a station as described in "Scanning stations".
2. Press the PROG button (11). The display will show
MEMORY and the respective preset location will begin to
flash.
3. Use the SKIP+ (12) and SKIP- (13) buttons to choose the
preset location for the corresponding station.
4. Press the PROG button again. The station will be preset.
The MEMORY indicator and the preset location will
disappear.