Alpine IVA-D310R Service Manual page 64

No. Symbol
46 DVD-STS
47 DVD-CMD
48 DVD-SCK
49 ACC-ON CONT
50 BUZZER
51 PWR-ON CONT
52 LCDAV+5V CONT
53 AV+8V CONT
54 AV+7V/5V CONT
55 AV-5V CONT
56 DC/DC+15V/-10V CONT
57 IS-FIN
58 BL+9V CONT(NC)
59 FFB-CONT1
60 PORTVDD1
61 DF B/G DIMMER
62 MTR-3
63 REMOCON IN
64 MTR-4
DF RED DIMMER (#1)
65
NC ($1)
66 R.REM-IN
67 FFB-CONT2
68 CLOSE ACT LED
69 SUB-STBY
70
SUB CLOCK
71
72 GND2
73
CLOCK
74
75 MNI(NC)
76 BL-PWM
77 FFB-CONT3
DIMMER-IN
78
(PULL-DOWN)
79 VLCD-CONT
80 ZX3
81 ZX2
82 ZX1
83 V-MUTE IN
84 DAC-M LATCH
85 DAC-M DATA
86 DAC-M CLK
87 OSD-RESET
88 N/P-SEL
89 REM-SEL
90 Y/COMP-SEL
NOTE : #1 : For IVA-D310R Model Only, $1 : For IVA-D310RB Model Only, Others : Common.
I/O
Serial data (status) signal input terminal from DVD Mechanism.
I
(EPF III communication)
Serial data (command) signal output terminal to DVD Mechanism.
O
(EPF III communication)
Serial communication synchronous clock output terminal to DVD Mechanism.
O
(EPF III communication)
O ACC ON power supply control output terminal.
O BUZZER signal output terminal.
O DVD system PWR-ON power supply control output terminal.
O LCD VISUAL 5V power supply control output terminal.
O VISUAL BUFF system 8V power supply control output terminal.
O AV +7V/+5V power supply control output terminal.
O AV -5V power supply control output terminal.
O DC/DC +15V/-10V power supply control output terminal.
I FRAME-IN signal terminal for IS-BUS communication.
- No connect terminal.
O Force feedback control signal-1 output terminal.
Power supply terminal for Port. (P00-P03, P10-P17, P30-P37, P100-P107,
-
P110-P117) (connect to VDD+5V)
O Blue/Green LED control PWM output terminal. (FRONT DF side)
O Motor control-3 terminal.
I Remote Control signal input terminal.
O Motor control-4 terminal.
O Red LED control PWM output terminal. (FRONT DF side)
- No connect terminal.
I Rear Remote Control input terminal.
O Force feedback control signal-2 output terminal.
O Action LED control signal (PWM) output terminal. (FRONT MOI side)
I Stand-by signal input terminal from MAIN u-COM.
- Crystal connect terminal for sub clock OSC.
- GND connect terminal.
- Crystal connect terminal for main clock OSC.
- No connect terminal.
O PWM signal output terminal for backlight lighting adjustment.
O Force feedback control signal-3 output terminal.
- Pull-down connect terminal.
O LCD brightness power supply control output terminal (PWM). (FRONT DF side)
O Screen mode control signal output terminal to timing control IC.
I Visual MUTE signal input terminal from DVD Mechanism.
O Latch control output terminal to DAC.
O Control data output terminal to DAC.
O Control clock output terminal to DAC.
O RESET signal output terminal to OSD/Flash Memory.
O NTSC/PAL switching signal output terminal. (H : NTSC, L : PAL)
O Remote Control signal output control terminal.
Brightness signal / composite signal switching signal output terminal.
O
(H : Y, L : Composite)
- 64 -
IVA-D310R/IVA-D310RB
Terminal Description
TO SCHEMATIC
TO CONTENTS