Anybus cB-RBS421 Product Manual

Wireless bridge serial - bluetooth

Advertisement

Quick Links

Anybus Wireless Bridge Serial -
Bluetooth Product Guide
Document Revision
Document number: XXX
Release: November 6, 2014
Document version:
Table of Content
1
Table of Content
2
Introduction
2.1
Related Documents
o
o
2.2
What is Bluetooth Wireless Technology?
2.3
How can I use my Serial Port Adapter?
o
2.4
Getting Started
o
3
Installation
o
3.1
Anybus Wireless Bridge Serial - Bluetooth
3.1.1
Mounting
3.1.2
Power Supply
3.1.3
RS232
3.1.4
RS422
3.1.5
RS485
3.1.6
Button and LED
4
Regulatory Information
4.1
FCC Statement
o
4.1.1
RF-Exposure Statement
4.1.2
Caution
4.2
Declaration of Conformity
o
5
Bluetooth Qualification
6
Additional Information
o
6.1
Guidelines for Efficient and Safe Use
6.1.1
Product Care
6.1.2
Radio Frequency Exposure
6.1.3
Electronic Equipment
6.1.4
Potentially Explosive Atmospheres
6.1.5
Power Supply
6.2
Troubleshooting
o
6.3
Technical Specifications
o
6.3.1
Environmental
6.3.2
Radio Output Power
6.3.3
Power Supply
6.3.4
Serial Interface
6.3.5
Housing
6.3.6
Dimensions
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the cB-RBS421 and is the answer not in the manual?

Questions and answers

Summary of Contents for Anybus cB-RBS421

  • Page 1 Table of Content  Introduction Related Documents What is Bluetooth Wireless Technology? How can I use my Serial Port Adapter? Getting Started  Installation Anybus Wireless Bridge Serial - Bluetooth  3.1.1 Mounting  3.1.2 Power Supply  3.1.3 RS232 ...
  • Page 2: Related Documents

    Brief overview of the features of the Anybus Wireless Bridge Serial – Bluetooth: Metal housing (IP65), long range (12 dBm), RS232/RS422/RS485 (DSUB) serial interface, stub antenna, accepts 8-30 VDC power supply.
  • Page 3: Getting Started

    How can I use my Serial – Bluetooth gateway? Your gateway communicates with its host system using RS232, RS422, or RS485. Once connected to its host system and configured, the gateway can communicate, using Classic Bluetooth and/or Bluetooth low energy, with a wide range of other Bluetooth enabled devices such as other gateways, mobile phones, handheld computers and laptops.
  • Page 4: Installation

    Before using the gateway it must be connected to its host system and it must be connected to a power supply. This chapter describes how to install the gateway. Anybus Wireless Bridge Serial - Bluetooth Mounting Figure 2.The gateway can be mounted using the mounting holes The Wireless Bridge must only be used with the antenna provided with the product.
  • Page 5 Power Supply The product shall have a power supply of 8-30 VDC, 1 W on pin 1 (-) and 2 (+) on the power connector. Use a female power connector 712 series from Binder. Figure 3. Power connector on the left side and the DSUB serial connector (male) in the middle Current consumption Current consumption measured at 30 V.
  • Page 6 RS232 This model supports RS232 with a male 9-pin DSUB:  Pin 1: NC, not connected  Pin 2: RD, input, receive data  Pin 3: TD, output, transmit data  Pin 4: DTR, output, data terminal ready  Pin 5: GND, ground ...
  • Page 7 RS422 In this model, the same DSUB connector is used when using RS232, RS422 and RS485. However, in the case of RS422 and RS485, the pins have different meanings compared to RS232. For details please read the AT command specification document.
  • Page 8 RS485 In the case of RS485, the same pinning as for RS422 is used, except that pins T- and R- must be connected externally and pins T+ and R+ must be connected externally to produce the signals T-/R- and T+/R+. For two-wire RS485 multidrop, the following connection setup shall be used: Figure 7.
  • Page 9: Regulatory Information

    Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 10: Declaration Of Conformity

    EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 IEC 60950-1:2005 + A1:2009 Medical Electrical Equipment IEC 60601-1-2 (2007) Bluetooth Qualification The Anybus Wireless Bridge Serial - Bluetooth has been qualified according to the Bluetooth specification. Bluetooth Device Referenced QDIDs specification...
  • Page 11: Additional Information

    Additional Information Guidelines for Efficient and Safe Use Read this information before using your gateway. For any exceptions, due to national requirements or limitations, when using your gateway, please visit www.bluetooth.com. Note: Changes or modifications to the product not expressly approved by HMS will void the user's authority to operate the equipment.
  • Page 12: Troubleshooting

    Troubleshooting This section lists some problems that you might encounter while using your Anybus Wireless Bridge Serial - Bluetooth. 1. I cannot connect. The data I send to the gateway does not arrive at the remote device.
  • Page 13 If high security mode has been selected on one of the devices wanting to communicate, the two devices have to be paired with each other. Either disable security or perform pairing. Also, note that pairing is automatic during a connection setup if it is needed. 2.
  • Page 14: Technical Specifications

    CTS/RTS flow control or no flow control. Housing Model Housing Anybus Wireless Bridge Serial - Bluetooth Aluminum housing, IP65. Dimensions Model Dimensions (width x depth x height) Anybus Wireless Bridge Serial - Bluetooth 75.8 x 85.5 x 35 mm (see Figure...

Table of Contents