Advertisement

R
O
T
CERTIFIED
A
R
Y
L
I
F
T
Entire contents © October 2000 by Rotary Lift. All rights reserved.
SPOA7, SPOA9, SPO9
Two Post Surface Mounted Lift
(200 Series Lifts)
SPOA7 Capacity 7,000lbs.
1750 lbs. per arm
SPO9 Capacity 9,000lbs.
2250 lbs. per arm
SPOA9 Capacity 9,000lbs.
2250 lbs. per arm
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
IN20008
Rev. P 10/04/00

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPOA7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Rotary SPOA7

  • Page 1 (200 Series Lifts) SPOA7 Capacity 7,000lbs. SPOA9 Capacity 9,000lbs. 1750 lbs. per arm 2250 lbs. per arm SPO9 Capacity 9,000lbs. 2250 lbs. per arm CERTIFIED IN20008 Entire contents © October 2000 by Rotary Lift. All rights reserved. Rev. P 10/04/00...
  • Page 2 (Passenger Side) 2' 2" (657mm) 15' 0" (4572mm) minimum to nearest obstruction 18" 7' 11-3/8" (2423mm) SPOA7* (457mm) 7' 3-3/8" (2219mm) SPOA7NB (Narrow Bay)* 8' 5-3/8" (2575mm) SPOA9* *NOTE: Dimension is from Inside of Baseplate to Inside of Baseplate. Fig. 1a 2' 5"...
  • Page 3 Fig. 1c 11' 4" (3454mm) Top of Overhead Assembly (Low Ceiling) SPO9 Column All above for both SPOA7 Extension and SPOA9 Use (4) 3/8"-16NCx1/2" (Low Ceiling is Flanged HHCS in front N/A for SPO9) and (2) in the back Latch Cable Guide Use (1) 3/8"...
  • Page 4 5. Lift Setting: Position columns in bay using If anchors do not tighten to 150 ft-lbs. installation torque, replace concrete under each column base with a 4' x 4' x dimensions shown in Fig. 1a & Fig. 1b. Place column 6"...
  • Page 5 Spacer & Flanged Locknut 1/4"-20NC x 2" HHCS & 1/4" Locknut 1/4"-20NC x 3/4" HHCS, Star Lockwasher, and Nut 105-3/8" SPOA7 Narrow Bay 3/8"-16NC x 3/4" HHCS 7-3/4" Spacer & Flanged Locknut 1/4"-20NC x 2" HHCS & 1/4" Locknut 1/4"-20NC x 3/4" HHCS, Star Lockwasher, and Nut 97-3/8"...
  • Page 6 Fill to vent hole with clean ad ven PUSH Dexron II ATF LEVER For Parts & Service contact: (800) 445-5438 Servic ROTARY LIFT / A DOVER INDUSTRIES CO. FT / A LOWER PUSH 10. Hoses: Clean adapters and hose. Inspect all threads LEVER Fig. 8a...
  • Page 7 Paragraph 21. (not included) at the lower cable tie off. The lengths required are as follows: Fig. 10a SPOA7 -NB or LC = 8" (203mm) Upper Sheaves -NB & LC = 16" (406mm) Lower Cable Tie Off SPOA9 &...
  • Page 8 1/2" hex jamb nut to lock in place. Latch Cable Then install cover and handle ball. Latch Cable Guide The left hole and slot is used for the SPOA7/SPOA9. The right Fig. 10b Fig. 11 hole and slot is used for the SPO9. Latch Cable Guide 5/16-18NC x 3/8"...
  • Page 9 60Hz. power supply to motor, Fig. 14 & 15. Size wire for 25 amp circuit. See Motor Operating Data Table. Single Phase Rotary Power Unit Never operate the motor on line voltage less CAUTION MOTOR OPERATING DATA - SINGLE PHASE than 208V.
  • Page 10 MOTOR OPERATING DATA - THREE PHASE 1. Unit not suitable for use in unusual conditions. Contact RUNNING MOTOR VOLTAGE RANGE LINE VOLTAGE Rotary for moisture and dust environment duty unit. 208 - 230 Volts 60 HZ 253 Volts 2. Control Box must be field mounted to power unit.
  • Page 11 NOTE: Once arm is installed in yoke, pull up actuator pin and swing arm fully around, being sure that the Restraint Gear and Gear Block always stay aligned. If they do not stay aligned, remove Right Rear & Left Front Arms restraint gear and install in the (8) 3/8-16NC x 1-1/2"...
  • Page 12 Column Arm Pin Padded section Short of door bumper Bumper faces out. Cotter Pin Long Bumper 21" (533mm) Fig. 19 Fig. 20 15. Wheel Spotting Dish: Position wheel spotting dish Remove fill-breather cap (and fill vent screw for Fenner as illustrated in Fig. 1a or 1b. Drill (2) 3/8" holes 2-1/2" Power Unit), Fig.
  • Page 13 15 lbs. Fig. 23 effort you should just pull the cables together. Adjust at 24. Rotary Decal Location: Clean area where decals are upper tie-offs Fig. 10a. to be placed. Remove backing from decals. Position and apply on approach sides of each column extension as 22.
  • Page 14 NOTES:...
  • Page 15 NOTES:...
  • Page 16 Thank You Trained Operators and Regular Maintenance Ensures Satisfactory Performance of Your Rotary Lift. Contact Your Nearest Authorized Rotary Parts Distributor for Genuine Rotary Replacement Parts. See Literature Package for Parts Breakdown. REV. CHANGE MADE Added Rotary power unit instructions.

This manual is also suitable for:

Spo9Spoa9

Table of Contents

Save PDF