Table of Contents
Advertisement
Available languages
Available languages
Flowchart
The flowchart below describes the various screens displayed on the 250V Power Supply and
the keys used to navigate through the screens.
1. Switch on Main Power Switch
2. Press
to set
or down load File .
Mode
3. Press
again to
Mode
4. Press
again to
Mode
5. Press
to choose
Constant
Volt or amperage
6. Press
Mode
Amp or Wat. which would like to adjust .
Time can't on 0:00 condition and the timer
should set 0:01 at least on each step.
On each step, the timer will count down till
time is up and then go to next step. Till
have run complete, the power supply will stop.
The parameters will be blinking 5 sec. After
5 sec., if you don't press any key , the
parameters will stop blinking and enter this
value to the power supply automatically .
START
4. Press
to start
power supply , the
PAUSE
parameters will stop blinking and LED
light on "
"
START
5. Press
again to
PAUSE
the LED is flashing
"
4. Press
to stop
power supply , the LED
STOP
will be off.
Mode
set total steps request .
enter setting condition.
Constant
Choose constant
Volt , the Volt's word
size will be bigger
than other words.
Amp. & WAT. will be
"maxi value" and
to choose
Volt; Time;
Time will be "00:00".
Press
Mod e
VoltBlinking, press
or decrease value
Press
Mod e
all steps
TIME Blinking, press
or decrease value
Press
Mod e
AMP Blinking, press
or decrease value
Press
Mod e
Wat. Blinking, press
or decrease value
Display "Constant Volt'
pause power supply ,
"
This stepcan press
Power Supply
3AP
START
STOP
Constant
PAUSE
Constant Mode
Program Mode
Press
choose constant mode
to
or program mode then
press
Mod e
Constant Mode
Constant Mode
Program Mode
Program Mode
FILE# : 01
STEPS : 02
File Blinking,
press
file #.
to set
FILE# : 01
STEPS : 02
STEPS Blinking, press
to set total steps request..
1
1
1
1
1
1
Choose constant
Amp, the Amp's word
size will be bigger
than other words.
Volt. & WAT. will be
"maxi value" and
Time will be "00:00".
Press
Mod e
1
1
1
1
AMP Blinking, press
to increase
to increase
or decrease value
Press
Mod e
1
1
1
1
TIME Blinking, press
to increase
to increase
or decrease value
Press
Mod e
1
1
1
1
Volt Blinking, press
to increase
to increase
or decrease value
Press
Mod e
1
1
1
1
Wat. Blinking, press
to increase
to increase
or decrease value
1
1
Display "Constant AMP'
1
1
to change condition. Process is same as step 4.
Mod e
1
1
1
1
.
Instruction Procedure
is same as Mode
302,
but this mode can
do
constant Watt.
1
1
Choose constant
Wat., the W's word
size will be bigger
than other words.
Volt . & Amp. will be
"maxi value" and
Time will be "0".
Press
Mod e
1
1
W Blinking, press
to increase
or decrease value
Press
Mod e
1
1
TIME Blinking, press
to increase
or decrease value
Press
Mod e
1
1
Volt Blinking, press
to increase
or decrease value
Press
Mod e
1
1
Amp. Blinking, press
to increase
or decrease value
1
Display "Constant Watt"
1
1
1
8
Advertisement
Chapters
Table of Contents
Troubleshooting
