Audiovox Pursuit PRO-9556 Installation Manual page 4

Action
Turn ignition on
Press and release the valet switch 3 times
Within 3 seconds, turn ignition Off, On, Off, On
This Action Accesses Feature Bank 3 Remote Start Selectable Features
First Press the valet switch one time
Press transmitter Lock button to change
Second Press and release the valet switch
Press transmitter Lock button to change
Third Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Press transmitter Lock button to change
Fourth Press and release the valet switch
Press transmitter Lock button to change
Fifth Press and release the valet switch
Press transmitter Lock button to change
Sixth Press and release the valet switch
Press transmitter Lock button to change
Seventh Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Eighth Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Ninth Press and release the valet switch
Press transmitter Lock button to change
Tenth Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Press transmitter Lock button to change
Eleventh Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Press transmitter Lock button to change
Twelfth Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Thirteenth Press and release the valet switch
Fourteenth Press and release the valet switch
Press transmitter Lock button to change
Fifteenth Press and release the valet switch
Sixteenth Press and release the valet switch
Seventeenth Press and release the valet switch
Press transmitter Lock button to change
Press and release the valet switch or turn the ignition off to:
Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the
programming will be terminated.
System Response
1 chirp = defrost output pulsed
2 chirps = defrost output 10 Mins
o r
2 chirps = RF start chirp on
1 chirp = RF start chirp off
o r
2 chirps = run time set for 10 mins
3 chirps = run time set fro 15 mins
4 chirps = run time set for 20 mins
1 chirp = run time set for 5 mins
o r
1 chirp = parking lights on steady w/RS active
2 chirps = parking lights flashing w/RS active
o r
2 chirps = tachometer input checking
1 chirp = voltage sense input checking
o r
1 chirp = greater than 0.5 V check before start
2 chirps = less than 0.5 V check before start
o r
2 chirps = ign 2 on during crank
3 chirps = ign 2 same as accessory
1 chirp = ign 2 off during crank
o r
2 chirps = ign 3 on during crank
3 chirps = ign 3 same as accessory
1 chirp = ign 3 off during crank
o r
1 chirp = diagnostics off
2 chirps = diagnostics on
o r
2 chirps = crank time 1.0 sec
3 chirps = crank time 1.5 sec
4 chirps = crank time 2.0 sec
1 chirp = crank time 0.8 sec
o r
1 chirp = unit set for gasoline engine
2 chirps = unit set for diesel engine 10 sec delay
3 chirps = unit set for diesel engine 15 sec delay
4 chirps = unit set for diesel engine 20 sec delay
o r
1 chirp = transponder output while R/S active
2 chirps = transponder output during start only
3 chirps = transponder output until ignition turned off
o r
Non Functional On This Unit
o r
1 chirp = crank averaging w/voltage input checking
2 chirps = preset crank time w/voltage input check
o r
Non Functional On This Unit
o r
Non Functional On This Unit
o r
1 chirp = aux o/p Black/Blue single pulse
2 chirps = aux o/p Black/Blue as alarm feature #1
Exit Programming Mode
4
No response
1 Chirp - LED 1 flash
Short chirp, then 2 long chirps
128-7770
4 of 20