Mo-vis P002-33 User & Installation Manual

Joystick interface e-fix 25

Advertisement

Quick Links

Joystick Interface e-fix 25
Contact & Product
mo-Vis BVBA
Biebuyckstraat 15 D
9850 Nevele - Belgium
Website:
www.mo-vis.com
E-mail:
contact@mo-vis.com
Telephone: +32 9 335 28 60
User & Installation Manual
User & Installation manual
Produced and published by
mo-Vis bvba, Belgium
Edition 1, April 2016
Manual item: D-P002-33-70-00
EN
P002-33

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P002-33 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mo-vis P002-33

  • Page 1: Contact & Product

    Contact & Product mo-Vis BVBA User & Installation manual Biebuyckstraat 15 D Produced and published by mo-Vis bvba, Belgium 9850 Nevele - Belgium Edition 1, April 2016 Website: www.mo-vis.com Manual item: D-P002-33-70-00 E-mail: contact@mo-vis.com Telephone: +32 9 335 28 60...
  • Page 2: Table Of Contents

    Important information about this Manual Congratulations for choosing a mo-Vis product! If you would like to learn more about mo-Vis and its products, we invite you to visit our website: www.mo-vis.com. Before you install or begin using this product, it is important that you read and understand the content of these installation and operating instructions, the safety instructions in particular.
  • Page 3: Support, Scrapping And Spare Parts

    Warranty mo-Vis bvba warrants the unit to be free from defects in material and workmanship for a period of 2 years under proper use, care and service. All warranties only cover parts and do not extend beyond the initial purchaser from an authorised mo-Vis dealer.
  • Page 4 In the event of a defect in material or workmanship, the dealer must obtain a return authorisation (RA) number from mo-Vis and the product must be shipped to a service centre designated by mo-Vis. mo-Vis will repair or, at mo-Vis’ option, replace any product covered by the warranty.
  • Page 5: Safety Precautions

    General The e-fix 25 interface is intended to be fitted on any power wheelchair with the e-fix 25 drive package to connect a mo-Vis Omni compatible device. Incorrect use or installation may lead to risk of injury to the user and damage to the wheelchair or other property.
  • Page 6: Design And Function Of The E-Fix 25 Interface

    Use only spare parts or accessories approved or recommended by mo-Vis. All other use could lead to changes which might impair the function and safety of the product. It could also lead to the warranty becoming void.
  • Page 7: Installation Instructions

    Connections The following connections are available on the e-fix 25 interface:  9-pole sub-d connector to connect a mo-Vis Omni Joystick.  Red and green jack socket of 3.5 mm to switch on/off the e-fix system.
  • Page 8 To connect the cabling to the Joystick e-fix 25 interface, proceed as follows: Place the unit according to the installation plan on the wheelchair. WARNING! Firmly secure the unit to the wheelchair. You can e.g. use Velcro of double-sided tape on the back of the unit. Connect the Omni Joystick cabling to the Omni Joystick input.
  • Page 9 Calibrating & configuring with the mo-Vis Configurator software Whenever connecting or replacing a mo-Vis joystick it is advised to calibrate and configure the joystick with the mo-Vis Configurator software.  This software must be installed and ready to use on a pc.
  • Page 10 Parameter Available values Description Mode Button No action The interface is always active Action (default) Activate The interface is only active when the mode button (connected to the joystick) is pressed during start-up of the wheelchair. If not pressed, the standard wheelchair joystick is activated.
  • Page 11: Using The Joystick Interface E-Fix 25

    Using the Joystick Interface e-fix 25 Use conditions The e-fix 25 interface is intended for use as installed by the dealer, in accordance to the installation instructions in this manual. The foreseen use conditions are communicated by the dealer or service engineer to the user and/or attendant during the first time use.
  • Page 12: Maintenance

    MSP Command Corrupt Corrupt command was Connection with the PC received. (Configurator program) went wrong, try again. MSP Command Unknown command was Connection with the PC Unknown received. (Configurator program) went wrong. Update Firmware or MSP Sub Command Unknown Sub Command was update Configurator Unknown received.
  • Page 13: Technical Data

    Technical data Name  E-fix 25 interface (P002-33) Compatibility  mo-Vis Omni Joystick compatible Connections  E-fix 25 male connector  Omni (SUB D9) female chassis connector  3.5mm mono jack socket (red)  3.5mm mono jack socket (green) ...
  • Page 14 Installation date: . . / . . / ..Dealer: ....Dealer stamp: Serial number sticker...

Table of Contents