Manual Recording From External Cd Player - Philips CDR775 S Instructions For Use Manual

Manual recording from external CD player

OPEN / CLOSE OPEN / CLOSE
PLAY / PAUSE PLAY / PAUSE REC
STOP
STOP
TYPE RECORD
FINALIZE ERASE
ANALOG RW
CDR 77X AUDIO CD RECOR
PROG
SHUFFL E
Important:
- Recording from CD-changers should always be started in the
Auto-Start mode.
- Only make analog recordings when digital recording is not
possible.
Preparing for manual recording
1 Make sure the disc is absolutely free of scratches and dust
particles.
2 Press EXT(ernal) SOURCE repeatedly until (depending on the
connection used):
DIGITAL I, OPTICAL I or ANALOG lights up and
DIGITAL 1, OPTICAL or ANALOG will appear on
the display.
REM REC TIME TRACK TOTAL
SYNC MANUAL
RECORD
CHANGER
DIGITAL I CD
•When Auto Track is On (default setting), track numbers will
automatically be increased during recording.
• To switch off the Auto Track function, you must enter
Menu mode.
If you wish to increase track numbers manually, press
TRACK INCR(ement) on the remote control. For further
instructions see Menu mode.
ON (auto): The track increments are automatically taken over
from the digital source material or after 2.7 seconds of
silence during analog recording.
OFF (manual): While recording, track numbers can be
incremented manually by pressing TRACK INCR(ement)
on the remote control. (Minimum track length is 4 sec.)
(This can also be done in Auto track on mode.)
• Track numbers cannot be changed after recording.
Note: Auto track works only with Consumer Sources with a
digital output signal according to the IEC 958
(consumer part) audio standard.
3 With the recorder stopped, press REC TYPE five times to
enter the Manual Record standby mode.
EASY JOG
STORE/
CANCEL/
MENU
DELETE
ENTER
EXT
SOURCE
DER
PHONES
DISPLAY
SCROLL REPEAT DJ MODE
REM TRACK TIME STEP
PROG
SHUFFLE ALL
CD
will start to flash and the display will show
MANUAL
REC EXT MAN followed by WAIT. After a few
seconds, PRESS RECORD followed by the remaining
time and track number will appear on the display.
REM REC TIME TRACK TOTAL
SYNC MANUAL RECORD
CHANGER
DIGITAL I CD
4 Play the source first to set the optimal recording level on
the CD recorder.
5 Rotate the EASY JOG/ENTER key until all the blue
segments are lighted on the Record/Play Level bar but the
red segments do not light continuously during the loudest
passages.
Display shows -XX DB (Decibel, e.g. -3DB).
6 Stop the source.
Start recording
1 To start recording, press RECORD on the CD recorder and
immediately start the source (from Pause or Stop mode).
d will light up continuously. The track number and
recording time left will appear on the display.
• If CHECK INPUT message also flashes, the digital
connection is incorrect.
• To record a 3-second silence at the start of a track, press
PAUSE on the CD recorder before starting the source.
• To check the total remaining recording time, press DISPLAY on
the CD recorder. (This can also be done during the recording.)
2 To stop recording, press STOP on the CD recorder.
UPDATE lights up and d goes out.
• If STOP is pressed within 3 seconds after RECORD, no
recording will take place.
• To interrupt recording, press PAUSE on the CD recorder.
d will start to flash. Press PAUSE again to restart
recording. (A new track will always be made.)
After recording the display will show UPDATE for several
seconds.
Note: With AUTO TRACK ON, the recorder will stop and go
to REC STANDBY for 1 minute and then goes to stop
mode automatically. Recordings from DAT, DCC or
recordings made analogously will stop after 20 seconds
of silence. With AUTO TRACK OFF, the auto stop
mode is disabled.
Important:
If you want to play the recorded CDR disc on a regular
CD player, it must be finalized. See finalizing discs .
Finalized CDRW discs play only on CDRW compatible
CD players.
For recording from CD changers always use REC EXT
DISC.
RECORDING
REM TRACK TIME STEP
PROG
SHUFFLE ALL
CD
21