Hinweise zu dieser Anleitung Lesen Sie diese Anleitung sorgfältig, bevor Sie ihre HomeMatic Komponenten in Betrieb nehmen. Bewahren Sie die Anleitung zum späteren Nach- schlagen auf! Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben Sie auch diese Bedienungs- anleitung.
Funktion • 4 Anschlüsse wahlweise als Eingänge oder als Ausgänge (über die HomeMatic-Zentrale) • Als Eingang konfigurierte Kanäle frei Konfigu- rierbar und beliebigen Aktorkanälen (auch von anderen Modulen) zuweisbar. • An einem als Eingang konfigurierten Kanal sind beliebig viele potentialfreie Taster parallel anschließbar. • Nichtflüchtiger Speicher für Konfigurationsdaten.
Page 7
Herausgeführte Adern: Bus A Bus B Busspannungsversorgung + Busspannungsversorgung - Kanal 1 Kanal 2 Kanal 3 Kanal 4...
Allgemeine Systeminformation zu HomeMatic Dieses Gerät ist Teil des HomeMatic Haussteuer- systems. Alle Geräte werden mit einer Standardkonfiguration ausgeliefert. Darüber hinaus ist die Funktion des Gerätes über ein Programmiergerät und Software konfigurierbar. Welcher weitergehende Funktions- umfang sich damit ergibt, und welche Zusatzfunkti- onen sich im HomeMatic System im Zusammenspiel...
Allgemeine Hinweise zum Bussystem 5.1 Allgemeine Hinweise zur Installation Grundsätzlich kann man die Anschlüsse der HMW- Komponenten in zwei Gruppen einteilen. In die Lastseite und in die Steuerseite (24 V- Spannungs- versorgung, Tastereingänge, RS485-Bus). Lastseite Da lastseitig typischerweise 230 V-Netzverbraucher geschaltet werden, ist hier der Einsatz von VDE- gerechten Installationsleitungen, wie beispielsweise NYM-Leitung etc., erforderlich.
von Fernmelde-Installationsleitung oder vergleich- barer Steuerleitung. Zu beachten ist allerdings, dass die Leitungen von Last und Steuerseite innerhalb der Unterverteilung getrennt entsprechend den VDE- Richtlinien zu verlegen sind. Dabei ist ein Mindest- abstand von 8 mm zwischen beiden Leitungsarten zu beachten. Beim Anschluss des RS485-Busses sind die A- Klemmen, die B-Klemmen, die 24 V-Spannungsver- sorgung und die Masseklemmen der Module einer...
Page 11
Steuer-PC bzw. einer Zentrale kommende Leitung an einem unter räumlichen Gesichtspunkten günstigen Ort zusammengeführt werden, um eine Trennung der einzelnen Busabschnitte zu erreichen und ggf. eine Fehlersuche zu vereinfachen. Üblicher- weise ist dies der Raum, in dem die Zentrale des HomeMatic-Systems installiert wird.
Zuordnung von Tastereingängen und Aktorkanäle Im Auslieferungszustand sind alle Kanäle des Gerätes als Tastereingänge konfiguriert. Sie können die Eingänge an beliebige am Bus befindliche Aktor- kanäle anlernen. 7.1 Anlernen von Tastereingängen an Aktorkanäle Bitte lesen Sie diesen Abschnitt erst voll- ständig, bevor sie mit dem Konfigurieren beginnen! Im Auslieferungszustand sind die Tasterein- gänge keinem Aktorkanal zugeordnet (auch nicht den Aktorkanälen des Gerätes an dem sie sich befinden) Zuordnung von Tastereingängen zu Aktorkanälen...
Page 14
eingang (am selben oder einem beliebigen anderen am Bus angeschlossenen Moduls) dem Sie den Aktor(kanal) zuordnen wollen. • Der Aktor(kanal) ist nun diesem Schalteingang zugeordnet, und die Kanal-LED am Aktor erlischt. • Testen sie die Zuordnung durch Drücken des zugeordneten Tasters. Der Aktor(kanal) sollte entsprechend der Konfiguration des Tasterein- gangs reagieren. • Wollen Sie den Aktor(kanal) einem weiteren Tastereingang zuordnen, so wiederholen sie diesen Vorgang.
Wird eine an einen Aktor angelernte Taste erneut an denselben Aktor angelernt, wird die alte Zuordnung überschrieben. 7.2 Aufheben der Zuordnung von Tasterein- gängen zu Aktorkanälen Aufheben der Zuordnung von Tastereingang und Aktor(kanal) • Drücken Sie die Programmiertaste des Aktor(kanals), dessen Zuordnung Sie aufheben möchten so lange, bis dessen Kanal-LED vom langsamen in das schnelle Blinken übergeht (nach ca.
Alle Anlernvorgänge können Sie durch kurzes Betätigen der Programmiertaste abbrechen. Wartung und Reinigung Das Produkt ist wartungsfrei. Überlassen Sie eine Reparatur einer Fachkraft. Technische Daten Kommunikation: RS485-Bus Spannungsversorgung: 24 V / DC Stromaufnahme: 25 mA Max. Ausgangsstrom: 15 mA Gehäuseabmessungen: 24 x 27 x 20 mm (H x B x T) (ohne Anschlußleitungen)
Page 17
Entsorgungshinweis: Gerät nicht im Hausmüll entsorgen! Elektro- nische Geräte sind entsprechend der Richt- linie über Elektro- und Elektronik-Altgeräte über die örtlichen Sammelstellen für Elektronik-Alt- geräte zu entsorgen. Das CE-Zeichen ist ein Freiverkehrszeichen, das sich ausschließlich an die Behörden wendet und keine Zusicherung von Eigenschaften beinhaltet.
Page 18
Function......20 General system information on HomeMatic . 22 General information on the bus system ..23 General information on the installation .
Information concerning these instructions Read these instructions carefully before beginning operation with your HomeMatic components. Keep the instructions handy for later consultation! Please hand-over the operating manual as well when you hand-over the device to other persons for use. Symbols used: Attention! This indicates a hazard.
Function • 4 connections, optionally as inputs or outputs (via the HomeMatic Center) • Channels configured as inputs can be con figured as desired and optional actuator chan- nels can be assigned (from other modules as well). • As many potentialfree buttons as are neces- sary can be connected to one input. • Nonvolatile memory for configuration data.
Page 21
Wires used: Bus A Bus B Bus power supply + Bus power supply - Channel 1 Channel 2 Channel 3 Channel 4...
General system information on HomeMatic This device is a component of the HomeMatic Home Control System. All devices are delivered in a standard configuration. The functionality of the device can also be con- figured with a programming device and software. Further resulting functionality and the additional functions provided in the HomeMatic system combined with other components are described in the separate Configuration Instructions and in the HomeMatic System Manual.
General information on Bus system 5.1 General information on the installation Basically, the connections of the HMW components can be divided into two groups. In the load side and in the control side (24 V power supply, button inputs, RS485 Bus). Load side Since normally a 230 V consumer is on the load side, using VDE-conforming installation wires, such...
and the control side are separated conforming with VDE regulations within the sub-distribution. Keep a minimum spacing of 8 mm between the two types of wiring. When connecting the RS485 bus, the A terminals, the B terminals, the 24 V power supply and the ground terminal of the modules of a sub-distribution (max.
Page 25
If central programming and control is to be done through the HomeMatic Centre, the HMW bus lines for the individual sub-divisions and the lines coming from the control PC or a Centre should be run together...
Assignment of button inputs and actuator channels All channels of the device are configured as button inputs in delivery status. You can teach the inputs for any actuator channels on the bus. 7.1 Teaching button inputs to actuator channels Please read this section completely before starting with any configuring! The button inputs are not assigned to any actuator channels in factory status (not the actuator channels of the device on which they are located either)
Page 28
bus) that you want to assign to the actuator (channel). • The actuator (channel) is now assigned with this switch input and the channel LED goes dark on the actuator. • Test the assignment by pressing the respective button. The actuator (channel) should react according to the configuration of the button input. • If you want to assign another button input to the actuator (channel), repeat this procedure. Depending on the actuator, button inputs are taught differently: Actuator...
If a button that was taught for an actuator is taught for the same actuator again, the old assignment is overwritten. 7.2 Clearing the assignment of button inputs to actuator channels Clearing the assignment of a button input and actuator (channel) • Press the programming button of the actuator (channel) that you want to clear the assignment for until the respective channel LED switches...
All teach procedures can be aborted by briefly actuating the programming button. Maintenance and cleaning This product is maintenance-free. Repairs are only to be done by trained professionals. Technical specifications Communication: RS485-Bus Voltage supply: 24 V / DC Current consumption: 25 mA Max.
Page 31
Instructions for disposal: Do not dispose off the device as part of household garbage! Electronic devices are to be disposed of in accordance with the guidelines concerning electrical and electronic de- vices via the local collecting point for old electronic devices.
Page 32
eQ-3 AG Maiburger Straße 29 D-26789 Leer www.eQ-3.com...