Special Product Features - Metabo KS 66 Plus Original Instructions Manual

Clean gummy or glue-contaminated saw blades.
Contaminated saw blades cause increased friction,
jamming of the saw blade and increase the risk of back-
kicks.
5. Overview
See page 2.
1 Guide plate
2 Adjusting screws for zero-play sliding on guide
rail (guide rail not included in scope of delivery,
see chapter on Accessories)
3 Locking screws (parallel stop)
4 Scale (diagonal cut angle)
5 Cutting indicator
6 Locking screws (diagonal cuts)
7 Parallel stop
8 Lever (for swivelling back the movable safety
guard) *
9 Cable guide
10 Locking button (switching on)
11 Trigger (switching on and off)
12 Nozzle (chip ejection)
13 Signal display *
14 Speed preselection wheel *
15 Hex screw (for splitting wedge setting)
16 Splitting wedge
17 Marking (saw blade outer diameter)
18 Inner saw blade flange
19 Movable safety guard
20 Saw blade
21 Outer saw blade flange
22 Saw blade fixing screw
23 Adjusting screw (adjust saw blade angle)
24 Lock nut (adjust saw blade angle)
25 Hexagon spanner
26 Locking screw (for setting cutting depth)
27 Scale (depth of cut)
28 Spindle locking button
* equipment-dependent

6. Special Product Features

• Metabo S-automatic safety clutch:
If the tool jams or catches, the power supply to
the motor is restricted. Due to the strong force
which can arise, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
• Mechanical safety brake for stopping saw blade
quickly when switching off the machine (KSE 68
Plus only).
• Hard-wearing guide plate made from lightweight
cast magnesium
• Vibration-damping, non-slip rubber coating in
grip area.
• Double-guided parallel stop, can be used on the
left and right for greater flexibility
• Lock preventing inadvertent machine start-up
• Lubricating system extends the service life of the
gearbox
• Vario Tacho Constamatic (VTC) full-wave
electronics for stepless speed adjustment. The
machine speed stays constant automatically
under load (only KSE 68 Plus)
• Setting wheel for speed preselection (only KSE
68 Plus)
• Electronic function monitoring the coil
temperature protects against overload. Light
signal when the machine begins to overload (only
KSE 68 Plus)
• External dust extraction possible: option of
connecting an extraction unit
• Carbon brushes for protecting the motor
• Guide rail available as an accessory (order no.
6.31213)
• Tool-less fine machine adjustment when used on
guide rail 6.31213
7. Initial Operation, Setting
Before plugging in, check to see that the rated
mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Always install an RCD with a max. trip current
of 30 mA upstream.
7.1 Setting splitting wedge
The splitting wedge (16) prevents the wood from
closing behind the saw blade and jamming it while
the machine is in operation. This could otherwise
lead to recoiling.
The splitting wedge must be set in such a way
that the distance between its inner curve and
the toothed ring on the saw blade is no greater than
5 mm. Set the splitting wedge so that the lowest
point of the saw blade does not protrude by more
than 5 mm below the bottom edge of the splitting
wedge. See illustration on page 2.
To adjust, loosen the hex screw (15), set the right
distances to the saw disc and tighten the hex screw
again.
7.2 Setting depth of cut
Loosen the locking screw (26). Raise or lower the
motor section against the guide plate (1). Read the
depth of cut that has been set from the scale (27).
Tighten the locking (26)screw again.
It is advisable to set the depth of cut in such a way
that no more than half of each tooth on the saw
blade juts out under the workpiece. See illustration
on page 3.
The clamping power of the locking screw (26) can
be adjusted. Unscrew the screw on the lever to do
this. Remove lever and mount offset anticlockwise.
Secure with screw. When doing this, note that the
cutting depth setting device moves freely when the
lever is open.
ENGLISH en
13