Environmental Protection; Technical Specifications - Metabo SRE 4350 TurboTec Original Instructions Manual

en ENGLISH
Recommended oscillating frequency settings:
Plastic materials . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Metal, Plexiglas ®
Coarse and fine sanding, polishing, wood . . . 5
The best way to determine the ideal setting is through
a practical trial.
7.3 TurboBoost switch
Actuate the TurboBoost switch (3) during operation to
switch on additional power reserves for maximum
material removal rate.
7.4 Dust extraction
To optimise the dust extraction performance, fit the
sanding disc such that the holes on the sanding disc
(9) and sanding plate (11) are aligned.
Own extraction system: Fit the dust collection box
(6) onto the exhaust nozzle until it engages. To
remove it, pull out the dust collection box (6).
To optimise the extraction performance, empty the
dust collection box (6) in good time and clean the filter
(8).
External dust extraction: Fit a suitable dust
extractor.
8. Cleaning, Maintenance
Empty dust collection box (6).
- Open cleaning flap (7).
- Remove fluted filter (8) and knock off dust stuck to
filter or remove with brush.
You can also clean fluted filter (8) under running
water (but make sure to dry the filter before use!).
- Empty the dust collection box (6), clean it thor-
oughly and ensure that any remaining dust is
removed.
- When inserting, ensure that the fluted filter (8) is
inserted in the lateral guides.
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the motor.
Replacing worn sanding plate (11)
- Remove fixing screws (on lower side of sanding
plate).
- Take off sanding plate.
- Sanding plate (as a spare part), see page 2.
- Mount sanding plate.
- Re-insert the fixing screws on the lower side of the
sanding plate (the screw must be inserted in the
existing thread pitch) and tighten (tightening torque
= 3.5 Nm +/- 0.2 Nm).
9. Accessories
Use only genuine Metabo accessories.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
10. Repairs
Repairs to electrical tools must be carried out by qual-
ified electricians ONLY!
If the mains connection cable of this machine is
damaged, it must be replaced by the manufacturer or
an authorized service centre to avoid hazard.
If you have Metabo electrical tools that require
8
, old coats of paint . . . . . . . . 3-4
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

11. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of power
tools in your household waste! In accordance
with European Guideline 2002/96/EC on used
electronic and electric equipment and its implemen-
tation in national legal systems, used power tools
must be collected separately and handed in for envi-
ronmentally compatible recycling.

12. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
A = Dimensions of sanding plate
P = Nominal power input
1
P = Power output
2
n = Idle speed (setting wheel)
0
n = Idle speed (TurboBoost switch)
0, TB
n = Speed at rated load (TurboBoost switch)
1, TB
s = Oscillating frequency at idle speed (setting
0
wheel)
s = Oscillating frequency at idle speed
0, TB
(TurboBoost switch)
s = Oscillating frequency at rated load
1, TB
(TurboBoost switch)
S = Oscillating circuit diameter
m = Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the emis-
sions from this power tool and compare these with
the values emitted by other power tools. The actual
values may be higher or lower, depending on the
particular application and the condition of the tool or
power tool. In estimating the values, you should also
include work breaks and periods of low use. Based
on the estimated emission values, specify protective
measures for the user - for example, any organisa-
tional steps that must be put in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value (surface grinding)
h
K = Uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
Wear ear protectors!