Advertisement
3)
Parameters settings
L i P o B A L A N C E C H G
Press
, the working mode will be blinking
2 . 0 A
O F F - L I N E
L i P o B A L A N C E C H G
Press
or
2 . 0 A
O F F - L I N E
Press
again, the current option will start blinking; Press
L i P o B A L A N C E C H G
2 . 0 A
O F F - L I N E
set the charging current with the range of 1.0A－20.0A.
Press
again to choose synchronous mode. Press
L i P o B A L A N C E C H G
1 0 . 0 A
O F F - L I N E
"MASTER" or "SLAVE".
L i P o B A L A N C E C H G
L i P o B A L A N C E C H G
1 0 . 0 A
M A S T E R
1 0 . 0 A
L i P o B A L A N C E C H G
Press and hold
M A S T E R
1 0 . 0 A
Charging Current
6S LiPo Battery
L P 6 S 1 0 . 0 A 2 3 . 1 8 V
B A L 0 3 5 : 1 0 0 3 5 1 0
Balance Charge Mode
Charging Time
Stop: if you'd like to terminate charging during the charging process, press
4)
Slave mode, any operation must be carried out on the Master channel.
5)
Finish: In charging mode, when the charging process comes to an end, the screen will be displayed
as below.
[ E N D : F I N I S H ]
2 5 . 2 0 V
SYNCHRONIZATION
PC1080 charger can be synchronized via data cables. Below illustrates how to charge 8 batteries of the
same type.
If a certain channel is selected as "Master" channel, then the other channels will be "Slave." The settings
on "Master" can be applied to all the chargers, which saves your time significantly.
to select BALANCE CHG, STORAGE or CHARGE
or
Either of the channels is MASTER, the other
will automatically change to 'SLAVE'. All the
S L A V E
settings must be done through "MASTER".
for 2 seconds to start charging.
Battery Voltage
Charging Capacity
. Under Master-
STOP
3 5 0 0 m A h
-3-
STORAGE
If a Lithium battery is not commonly used, it's highly recommended to charge or discharge the battery to
3.9V with Storage mode so as to extend the battery life. If the battery voltage is higher than 3.9V, then
discharging the battery will be necessary; If less than 3.9V per cell, do the reverse. Please note both
charge or discharge must be under Storage mode.
L i P o B A L A N C E C H G
2 . 0 A
O F F - L I N E
or
to
L i P o
S T O R A G E
2 . 0 A
O F F - L I N E
to set
CHARGE
It targets Lithium battery with no balance lead. Always keep in mind that the battery must be
a six-cell battery
B a l a n c e P o r t
E n a b l e
B a l a n c e P o r t
D i s a b l e
L i P o C H A R G E
2 . 0 A
O F F - L I N E
SWITCH BETWEEN LIPO AND LIHV
This function must be used with caution, as charging incorrect type of battery will damage
the battery, or even cause fire or explosion.
Press and hold
appears on the screen.
Press
the charging mode will blink.
Press
or
to select STORAGE mode.
Turn off the Balance Port in the SYSTEM SETUP. Press
Press
or
to switch to OFF; Press
Press
several times to access Charge mode.
STOP
and
at the same time for 5 seconds until the corresponding battery type
L i P o B A L A N C E C H G
L i H V B A L A N C E C H G
2 . 0 A
O F F - L I N E
2 . 0 A
-4-
, ON will blink;
again to confirm OFF.
O F F - L I N E
Advertisement
