Related Manuals for Honeywell LANSRLU1
Summary of Contents for Honeywell LANSRLU1
- Page 1 Available Now At Click Here LANSRLU1 Lantronix UDS100 QuickStart User Guide 7-101002-00...
-
Page 2: Table Of Contents
LANSRLU1 Honeywell Access Systems Contents Overview ........3 Requirements for WIN-PAK 2.0/Pro R3 and Higher . -
Page 3: Overview
Honeywell Access Systems LANSRLU1 Overview The LANSRLU1 (UDS100) Device Server connects serial devices such as Secu- rity Alarms and Access Control Devices to Ethernet networks using the IP proto- col family. The UDS100 connects these devices through a TCP data channel or through a Telnet connection to computers or another Device Server. -
Page 4: Leds
LANSRLU1 Honeywell Access Systems LEDs The UDS100 device uses LEDs to indicate the following conditions: 10 Mbps Link/Activity (green) • 100 Mbps Link/Activity (green) • Collisions • Diagnostics (red) • Status (yellow) • LEDs Definition 10 Mbps Link/Activity steady (green). -
Page 5: Programming
Honeywell Access Systems LANSRLU1 Programming DeviceInstaller The user can manually assign the IP address using the DeviceInstaller, which is on the product Lantronix CD. Install the DeviceInstaller Insert the product CD into your CD-ROM drive. The Lantronix UDS100 Device Server window displays. - Page 6 LANSRLU1 Honeywell Access Systems Once the MAC Address, IP After receiving a response from Address and Subnet Mask have the unit(s), displaying the been entered, select the Set IP assigned IP, select 'Save'. Address button. DeviceInstaller will then per- form the following steps before...
- Page 7 Honeywell Access Systems LANSRLU1 At the Gateway IP Address prompt Hit enter immediately if no gateway is required. Type 'Y', if a gateway is used. If the user selects 'Y', at the Gateway IP Addr (000) prompt, enter the gate- way address then <enter>.
-
Page 8: Programming The Uds100 With Windows Command Prompts
LANSRLU1 Honeywell Access Systems At the ConnectMode (C0) The user will then notice a screen prompt, enter C1 for remote con- specifying a Target Source. figuration then <enter>. At the Remote IP Address prompt, if configuring the Remote UDS100 at this time, press the enter key four times so no Remote IP is assigned. -
Page 9: Serial Programming Through Hyperterminal
Honeywell Access Systems LANSRLU1 The user will notice an error mes- A Lantronix Device Universal sage that reads as follows: Server DOS screen will appear prompting the user to Press Enter Could not open a connection to to go into Setup Mode. Press host on Port 1: connection failed <enter>. -
Page 10: Win-Pak 2.0/Pro/Intl. R3 Configuration With Uds100
LANSRLU1 Honeywell Access Systems WIN-PAK 2.0/Pro/Intl. R3 Configuration with UDS100 Be sure all devices are properly Under Port, press the drop down configured and attached over the arrow and select TCP/IP connec- network. tion. Log into the WIN-PAK 2/Pro At this point, enter an IP Address User Interface. -
Page 11: System Design
Honeywell Access Systems LANSRLU1 System Design Null Modem Gender Changer 25-pin M-M UDS100 Device N485PCI2L RS-232 PANELS ETHERNET CABLE NCI Card Connection Alternatives Connection Description Remedy N-485-HUB-2 • 25-pin male on serial end. Replace the HUB firmware chip with • HUB firmware is used for a PCI firmware chip. -
Page 12: Problems And Error Messages
LANSRLU1 Honeywell Access Systems Problems and Error Messages Problem/Message Reason Solution When issuing the ARP -S The user currently logged Have someone from the IT command in Windows, in does not have the cor- department log in a user- "The ARP entry addition rect rights to use this com- with sufficient rights. - Page 13 Honeywell Access Systems LANSRLU1 Problem/Message Reason Solution When attempting to assign The cause is most likely Double-check the speci- an IP with DeviceInstaller, one of the following: The fied parameters. Tip: An IP the following message Hardware address speci- address cannot be appears: "No response...
- Page 14 LANSRLU1 Honeywell Access Systems Problem/Message Reason Solution It’s possible to ping the There may be an IP Turn the UDS off and then UDS, but not Telnet to the address conflict on the issue the following com- UDS on port 9999.
- Page 15 Honeywell Access Systems LANSRLU1 Problem/Message Reason Solution The correct serial cable is If the serial cable is cor- Check to see whether used, and the UDS is rect, perhaps it is not con- there is a socket connec- setup correctly, but there is...
-
Page 16: Adapter Pinouts For 9-Pin And 25-Pin Connectors
Note: RX = Receive; TX = Transmit; SG = Ground. Honeywell Access Systems 135 West Forest Hill Avenue Oak Creek, WI 53154 PH: 414-766-1700 FX: 414-766-1798 www.honeywellaccess.com Specifications subject to change without notice. © 2004 Honeywell International. All rights reserved. 7-101002-00...