Subscribe to Our Youtube Channel
Related Manuals for CSI CT24
Summary of Contents for CSI CT24
- Page 1 Installation / Operation Manual Fully Automatic & Demand Water Softeners with Signature Series Control Valve CSI Water Treatment Ashland, Ohio...
- Page 2 General CT24 CT32 Specifications CT24V CT32V Grains Capacity / Regeneration 23,100 30,800 20,200 26,900 9,800 13,100 Maximum Raw Water Hardness (grains) Maximum Clear Iron / Manganese (ppm) Salt Used / Regeneration (pounds) 11.2 15.0 Exchange Resin (cu. ft.) 1.00 Mineral Tank (Polyglass)
- Page 3 General CM24 CM32 Specifications CM24V CM32V Grains Capacity / Regeneration 23,100 30,800 20,200 26,900 9,800 13,100 Maximum Raw Water Hardness (grains) Maximum Clear Iron / Manganese (ppm) Salt Used / Regeneration (pounds) 11.2 15.0 Exchange Resin (cu. ft.) 1.00 Mineral Tank (Polyglass) 8 x 35 10 x 35 Service Flow Rate (gpm)*...
-
Page 4: How A Water Softener Works
PLEASE NOTE THESE SPECIFICATIONS BEFORE PROCEEDING OPERATING PRESSURE RANGE : 20 - 125 PSI OPERATING TEMPERATURE RANGE : 33º F - 120º F INLET / OUTLET PIPE SIZE : 3/4: FNPT PLEASE COMPLY WITH ALL APPLICABLE PLUMBING CODES PROTECT THE SOFTENER AND PIPING FROM FREEZING TEMPERATURES Please read the entire Owner’s Manual and Instruction before installation. -
Page 5: Installation Requirements
Installation Requirements • A level floor position ahead of piping into water heater. • Unit must be installed at least 10' ahead of the inlet to a water heater to prevent damage due to back-up of hot water. • DO NOT install the unit in an area of direct sunlight or where freezing temperatures may occur! (See Installation Diagrams for proper placement and plumbing connections.) Major System Components : 1. -
Page 7: Drain Line Connection
Softener Location / Other Requirements • Locate the unit near an unswitched, 120 volt / 60 Hz grounded electrical outlet. • Check for distance and proper drain installation (e.g. floor drain, washing machine standpipe). • Determine type and size of piping required for softener connection (e.g. copper, galvanized, PVC plastic). Note : If household plumbing is galvanized and you intend to make the installation with copper (or vise versa), obtain di-electric unions to prevent dissimilar metal corrosion. -
Page 8: Electrical Connection
- Brine Line and Overflow Connection - 1. Position brine tank on a smooth, level surface near the softener resin tank. If necessary, the brine tank can be placed at a higher level than the resin tank, but never at a lower level. 2. - Page 9 - How To Use The Capacity Charts - EXAMPLE HARDNESS = 20 gpg 20 gpg UNIT SELECTED 32,000 grain IRON = 3 ppm x “4" 12 gpg NUMBER OF PERSONS MANGANESE = 1 ppm x “4" 4 gpg COMPENSATED HARDNESS 36 gpg TOTAL COMPENSATED HARDNESS 36 gpg...
- Page 10 Model TS32 & TS32V Models # of People Hardness Range Regeneration Frequency (# Days) 3 - 10 11 - 20 21 - 30 31 - 40 41 - 50 51 - 60 61 - 75 Model TS48 & TS48V Models # of People Hardness Range Regeneration Frequency (# Days)
- Page 11 Model TS96V Model # of People Hardness Range Regeneration Frequency (# Days) 3 - 20 21 - 30 31 - 40 41 - 50 51 - 60 61 - 70 71 - 80 81 - 90 91 - 100 Model TS128V Model # of People Salt Setting...
-
Page 12: Control Valve Operation
Note : Salt settings are pre-set at the factory for the maximum shown on the capacity charts. If an economy salt setting is desired, refer to page 8, item 4 in the Signature Series Service Manual. Warning : Do not reduce salt settings below 9 lbs. as the water level in the brine tank will not reach the grid plate. - Control Valve Operation - Refer to page 4, item 2 of the Signature Series Service Manual Instructions. -
Page 13: General Care And Cleaning
You should manually bypass the softener if : 1. The outside lines do not bypass the water softener and water is to be used for lawn sprinkling or other similar uses. 2. Servicing the water softener. 3. A water leak from the water softener is evident. 4. -
Page 14: Limited Warranty
* From Date of Installation LABOR, ETC., COSTS : CSI Water Treatment shall IN NO EVENT be responsible or liable for the cost of field labor or other charges incurred by any customer removing and/or reaffixing any CSI Water Treatment product, part or component thereof.
Need help?
Do you have a question about the CT24 and is the answer not in the manual?
Questions and answers