Page 1: Table Of Contents
9.12. Removal of P-Board (MAIN_1) ----------------------- 29 7.1. Self Check--------------------------------------------------17 9.13. Removal of P-Board (MAIN_2) ----------------------- 30 7.2. No Power ---------------------------------------------------19 9.14. Removal of P-Board (SUB)---------------------------- 30 © Panasonic Corporation 2009 Unauthorized copying and distribution is a violation of law.
Page 2 TH-103PF12E 9.15. Removal of S1-Board and V2-Board---------------- 30 9.16. Removal of SU-Board ---------------------------------- 31 9.17. Removal of SM-Board ---------------------------------- 32 9.18. Removal of SD-Board ---------------------------------- 32 9.19. Removal of SC-Board----------------------------------- 33 9.20. Removal of SS2-Board -------------------------------- 34 9.21. Removal of SS3-Board -------------------------------- 35 9.22.
Page 3: Safety Precautions
TH-103PF12E 1 Safety Precautions 1.1. General Guidelines 1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials. 2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the wires have been broken or disconnected, do not attempt to repair or re-wire the units.
Page 4: Warning
TH-103PF12E 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi- tive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip”...
Page 5: About Lead Free Solder (Pbf)
TH-103PF12E 2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
Page 6: Service Navigation
TH-103PF12E 3 Service Navigation 3.1. Service Hint...
Page 7 TH-103PF12E Board Name Function Board Name Function Digital Signal Processor, Microcomputer Power switch Format Converter, Plasma AI Processor C1 (upper) Data drive (1) (upper) Sub-Field Processor C2 (upper) Data drive (2) (upper) Slot Interface (Audio / Video / Sync Input Switch),...
Page 8: Applicable Signals
TH-103PF12E 3.2. Applicable signals...
Page 9: Specifications
TH-103PF12E 4 Specifications Power Source 220-240 V AC, 50/60Hz Power Consumption Power on 1450 W Stand-by condition Save OFF 1.2 W, Save ON 0.7 W Power off condition 0.4 W Plasma Display panel Drive method: AC type 103-inch, 16:9 aspect ratio 2,269 mm (W) ×...
Page 10: Operating Instructions
TH-103PF12E 5 Operating Instructions...
Page 11 TH-103PF12E Option Menu for GPF12D series GPF12D chassis series have special function and operation setting facility called Option Menu. This Option Menu is useful for special function required customers. This should be set at the installation stage. Option menus default setting...
Page 12: Service Mode
TH-103PF12E 6 Service Mode 6.1. CAT (Computer Aided Test) mode To exit the CAT mode, access the ID mode and switch off the main power. 6.1.1. IIC mode Select the IIC mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action button on the remote control.
Page 13 TH-103PF12E 6.1.2. CD mode Select the CD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. Memory data change To exit the CD mode, press the R button on the remote control.
Page 14 TH-103PF12E 6.1.4. SD mode Select the SD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action button on the remote control. To exit the SD mode, press the R button on the remote control.
Page 15 TH-103PF12E 6.1.6. ID mode Select the ID mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. To exit the ID mode, press the R button on the remote control.
Page 16: Iic Mode Structure (Following Items Value Is Sample Data)
TH-103PF12E 6.2. IIC mode structure (following items value is sample data)
Page 17: Troubleshooting Guide
TH-103PF12E 7 Troubleshooting Guide 7.1. Self Check 7.1.1. Display Indication 1. Self-check is used to automatically check the bus line controlled circuit of the Plasma display. 2. To get into the Self-check mode, press the volume down button on the customer controls at the bottom of the set, at the same time pressing the OFF-TIMER button on the remote control, and the screen will show.
Page 18: Power Led Blinking Timing Chart
TH-103PF12E 7.1.2. Power LED Blinking timing chart 1. Subject Information of LED Blinking timing chart. 2. Contents When an abnormality has occurred to the unit, the protection circuit operates and resets to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
Page 19: No Power
TH-103PF12E 7.2. No Power First check point There are following 3 states of No Power indication by power LED. 1. No lit. 2. Green is lit then turns red blinking a few seconds later. 3. Only red is lit. 7.3.
Page 20: Local Screen Failure
TH-103PF12E 7.4. Local screen failure Plasma display may have local area failure on the screen. Fig - 1 is the possible defect P.C.B. for each local area. Fig - 1...
Page 21: Service Fixture & Tools
TH-103PF12E 8 Service Fixture & Tools 8.1. SC jig Purpose: To find the failure board (SC or SU/SM/SD) when the power LED is blinking 7 times. SC jig: Jumper connector to connect to SC50 connector on SC board Part number:...
Page 22: Disassembly And Assembly Instructions
TH-103PF12E 9 Disassembly and Assembly Instructions • To disassemble P.C.B., wait for 10 minute after power was off for discharge from electrolysis capacitors. • marks indicate screw positions. 9.1. Rear Cover and Board Rear Cover required to remove for each board exchange.
Page 23: Location Of Rear Cover Screws
TH-103PF12E Board Name Rear Cover V3-Board A, B, C, D, E, F PB-Board P-Board (MAIN_1) P-Board (MAIN_2) P-Board (SUB) D, E HX-Board HL-Board Unnecessary DN-Board HDE-Board Unnecessary 9.2. Location of Rear Cover screws 9.2.1. Removal of Rear Cover ( A )
Page 24 TH-103PF12E 9.2.3. Removal of Rear Cover ( C ) , ×2 2. Remove screws (×21 ) and then remove the Rear Cover ( A ). 1. Remove screws (×19 ) and then remove the Rear Cover ( C ). 9.2.2.
Page 25: Removal Of Side Angle (L), (R)
TH-103PF12E 9.2.5. Removal of Rear Cover ( E ) 2. Remove screws (×21 ) and then remove the Rear Cover ( F ). 1. Remove screws (×25 ) and then remove the Rear Cover ( E ). 9.3. Removal of Side Angle (L), (R) Note: when fixing Rear Cover ( E ) •...
Page 26: Removal Of Hde-Board
TH-103PF12E 2. Remove 19 screws and then remove the Side Angle (L). 5. Remove 4 screws (B) of the Plate. 6. Remove 19 screws and then remove the Side Angle (R). 9.3.2. Removal of Side Angle (R) 1. Disconnect the connectors (DS15, P34).
Page 27: Removal Of Hl-Board
TH-103PF12E 9.5. Removal of HL-Board 3. Remove 2 screws (J). 4. Remove 1 screw (K) and then remove H5-Board. 1. Remove 4 screws (F) and then remove the HL Terminal Block. 2. Remove 4 screws (G). 3. Remove 2 screws (H) and then remove HL-Board.
Page 28: Removal Of Hx-Board
TH-103PF12E 4. Disconnect the connector (DS14). 1. Remove the Slot Case. 5. Remove 10 screws and then remove the Fixed Plate (Refer to Removal of DS-Board) 2. Disconnect the connector (HX1). 3. Remove 4 Hexagonal-Head screws and 2 screws and then remove HX-Board.
Page 29: Removal Of Pb-Board
TH-103PF12E 9.10. Removal of PB-Board 2. Disconnect the connectors (D3, D5, D21, D25). 3. Remove the flexible cables from the connectors (D20, D31, D32, D33, D34). 4. Remove 4 screws and then remove D-Board. 1. Disconnect the connectors (PB30, PB31, PB51, PB53, PB54, PB59, PB61, PB62, PB67, PB69, PB71).
Page 30: Removal Of P-Board (Main_2)
TH-103PF12E 9.13. Removal of P-Board (MAIN_2) 9.15. Removal of S1-Board and V2- Board 1. Disconnect the connectors (CM1, CM2, CM3, CM4, P6, P11, P35). 1. Remove 2 screws ( ). 2. Remove 10 screws and then remove P-Board (MAIN_2). 2. Remove 2 screws ( ) and then slide the Side Power Unit upward.
Page 31: Removal Of Su-Board
TH-103PF12E 9.15.2. Removal of V2-Board 4. Disconnect the Fan relay connectors. 5. Remove 4 screws and then remove the Fan Block (2, 3). 1. Remove 4 screw (N) and then remove the Side Power Cover. 2. Disconnect the connector (V15) and then remove V2- Board.
Page 32: Removal Of Sm-Board
TH-103PF12E 10. Disconnect the connector (SU43). 4. Remove the flexible cables from the connectors (SM1, SM2, SM3, SM4, SM11, SM12). 11. Remove 5 screws ( ). 12. Remove 3 screws ( ) and then remove SU-Board. 9.17. Removal of SM-Board 5.
Page 33: Removal Of Sc-Board
TH-103PF12E 1. Remove the Side Angle (R). 8. Remove the flexible cables from the connectors (SD1, (Refer to Removal of the Side Angle (R)) SD2, SD3, SD4, SD12). 2. Remove 3 screws ( ). 3. Remove 3 screws ( ) and then remove the Reinforce- ment Angle (lower_right).
Page 34: Removal Of Ss2-Board
TH-103PF12E 9.20. Removal of SS2-Board 1. Remove SU-Board. (Refer to Removal of SU-Board) 2. Remove SD-Board. (Refer to Removal of SD-Board) 3. Disconnect the connectors (SM41, SM42, SM46). 4. Remove 6 screws ( ). 5. Remove 4 screws ( ) and then turn over SM-Board to the left.
Page 35: Removal Of Ss3-Board
TH-103PF12E 6. Disconnect the connectors (SS34, SS35). 4. Disconnect the connectors (SS32, SS33). 7. Remove the flexible cables from the connectors (SS51, 5. Remove the flexible cables from the connectors (SS59, SS52, SS53, SS54). SS60, SS61, SS62). 8. Remove 6 screws and then remove SS2-Board.
Page 36: Removal Of Fan
TH-103PF12E 5. Disconnect the connectors (SS11, SS21, SS32, SS33, SS34, SS35). 6. Remove the flexible cables from the connectors (SS55, SS56, SS57, SS58). 7. Remove 13 screws and then remove SS-Board. 9.23. Removal of Fan 3. Remove each 4 screws and then remove the Fan (A, B, C, D, E, F, G, H, J).
Page 37: Removal Of C1-Board (Upper)
TH-103PF12E 1. Remove the Reinforcement Angle (upper_right). (Refer to Removal of SU-Board) 2. Remove the flexible cable from the connector (C11). 3. Remove 4 screws ( ) and then remove the flexible cables from the connectors (CA1, CA2). 4. Remove 4 screws ( ) and then remove C1-Board (upper).
Page 38: Removal Of C3-Board (Upper)
TH-103PF12E 9.26. Removal of C3-Board (upper) 7. Remove the flexible cables from the connectors (C30, C31, C32). 8. Remove 6 screws ( ) and then remove the flexible cables from the connectors (CA6, CA7, CA8). 9. Remove 6 screws ( ) and then remove C3-Board (upper).
Page 39: Removal Of C5-Board (Upper)
TH-103PF12E 9.28. Removal of C5-Board (upper) 1. Remove the Reinforcement Angle (upper_left). (Refer to Removal of SS2-Board) 2. Remove the flexible cable from the connector (C61). 3. Remove 4 screws ( ) and then remove the flexible cables from the connectors (CA15, CA16).
Page 40: Removal Of C2-Board (Lower)
TH-103PF12E 9.31. Removal of C2-Board (lower) 2. Remove 3 screws ( ). 3. Remove 2 screws ( ) and then remove the Rear Cover Angle (lower_center). 1. Remove the Reinforcement Angle (lower_left). (Refer to Removal of SS3-Board) 2. Remove the flexible cables from the connectors (C20, 4.
Page 41: Removal Of C5-Board (Lower)
TH-103PF12E 9.35. Removal of C6-Board (lower) 1. Remove the Reinforcement Angle (lower_center). (Refer to Removal of C3-Board (lower)) 2. Remove the flexible cables from the connectors (C40, C41, C42). 3. Remove 6 screws ( ) and then remove the flexible cables from the connectors (CA9, CA10, CA11).
Page 42: Removal Of Front Glass, V1, V3-Board And Cabinet Assy
TH-103PF12E 1. Remove 2 screws and then remove AC Inlet Cover. 2. Remove 2 screws ( ). 3. Remove 2 screws ( ) and then slide the Side Power Unit upward. 4. Remove the Side Power Unit. 5. Remove 24 screws and then remove Cabinet Block.
Page 43 TH-103PF12E 9.37.1. Removal of Front Glass Note: when Cabinet or Front Glass is exchanged • You need new Aluminum Tape kit when you exchange 1. Remove 44 screws and then remove the Fixed Angles the Cabinet or Front Glass. (left, right, upper, lower).
Page 44 TH-103PF12E 9.37.2. Removal of V1-Board and V3-Board 4. Remove 20 screws and then remove the Cabinet Joint Metals (B, BS). 1. Remove 1 screw (P). 2. Disconnect the connector (V1) and then remove V1- Board. 3. Remove 1 screw (Q).
Page 45: Removal Of Plasma Display Panel
TH-103PF12E Note: when Cabinet or Front Glass is exchanged • You need new AL Tape kit when you exchange the Cab- inet or Front Glass. Note • The felts are parts which cannot be recycled. Please use the new article when you exchange the Cabinet.
Page 46 TH-103PF12E 9. Remove each 4 screws (R) of the Plates. 3. Remove 2 screws ( ). 4. Remove 2 screws ( ) and then slide the Side Power Unit upward. 5. Remove the Side Power Unit. 6. Remove 24 screws and then remove Cabinet Block.
Page 47 TH-103PF12E 13. Remove 6 screws ( ). 14. Remove 4 screws ( ) and then remove the Rear Cover Angles (upper_center, lower_center). 17. Disconnect the connectors (DN3, DN5, DN9). 18. Remove the flexible cables from the connectors (DN1, DN2). 19. Remove 5 screws and then remove the DN-Board and 15.
Page 48 TH-103PF12E 22. Disconnect the connectors (DS4, DS6). 28. Disconnect the connectors of P-Board (Main_2) (CM1, 23. Remove 3 screws and then remove the Slot Block. CM2, CM3, CM4, P6, P11). 29. Remove 10 screws and then remove P-Board (MAIN_2). 30. Disconnect the connectors (P9, P25).
Page 49 TH-103PF12E 36. Remove 4 screws and then remove PB-Board. 40. Remove the Duct Barrier E, Duct Barriers F, Duct Barrier G, Duct Barrier H, Duct Barrier L, Duct Barrier N and Duct Barrier O. 41. Exchange the Plasma Display Panel.
Page 50: Measurements And Adjustments
TH-103PF12E 10 Measurements and Adjustments 10.1. Adjustment Procedure 10.1.1. Driver Set-up 10.1.1.1. Item / Preparation 10.1.1.2. Adjustments 1. Set Aging pattern (white pattern signal) by IIC mode. 2. Set the picture controls as follows. Adjust driver section voltages. (Refer to the panel data on the Picture menu: Standard Panel Label).
Page 51: Initialization Pulse Adjust
TH-103PF12E 10.1.2. Initialization Pulse Adjust 1. Set Aging pattern (white pattern signal) by IIC mode. 2. Set the picture controls as follows. Picture menu: Standard Picture: +25 Aspect: Full 3. Connect Oscilloscope to TPSC1 and adjust VR16601 for 125V ± 5V.
Page 52 TH-103PF12E 10.1.3. P.C.B. (Print Circuit Board) and Plasma Display Panel exchange 10.1.3.1. Quick adjustment after P.C.B. and Panel exchange 1. To remove P.C.B., wait 10 minute after power was off for discharge from electrolysis capacitors. 10.1.3.2. Quick adjustment after P.C.B. exchange Adjust the following voltages with the multimeter.
Page 53 TH-103PF12E 3. Check that the Ve Mode is set to 3. 4. Pless R button and then select and display Ve Init. 5. Check TPVE and adjust the volume. 6. Exit the IIC mode. 10.1.7. Ve Life adjustment 10.1.7.1. After exchange both D board and DN board 1.
Page 54 TH-103PF12E 10.1.9. Adjustment Volume Location 10.1.10. Test Point Location...
Page 55: Adjustment
TH-103PF12E 10.2. Adjustment 10.2.1. RGB white balance adjustment Instrument Name Connect to Setting • RGB VGA60 W / B pattern PC input User setting: Normal • Color analyzer Panel surface (Picture menu: STANDARD) (Minolta CA-100 or equivalent) Steps Remarks [Condition] Picture Menu: Standard •...
Page 56 TH-103PF12E...
Page 57 TH-103PF12E 10.2.2. YUV white balance adjustment Instrument Name Connect to Setting • HD(1125/60i) W / B pattern (COMPONENT Output) PC input User setting: Normal • Color analyzer Panel surface (Picture menu: STANDARD) (Minolta CA-100 or equivalent) Steps Remarks [condition] Picture Menu: STANDARD •...
Page 58 TH-103PF12E...
Page 59: Block Diagram
TH-103PF12E 11 Block Diagram 11.1. Diagram Notes...
Page 60: Main Block (1 Of 2) Diagram
TH-103PF12E 11.2. Main Block (1 of 2) Diagram DS SLOT INTERFACE/SYNC PROCESSOR/SOUND PROCESSOR AUDIO OUT AUDIO TERMINALS SELECT L/R_1 L/R_2 R LINE OUT SOUND AUDIO OUT MUTE L/R_3 L LINE OUT CONTROL TERMINAL L/R_4 EQUALIZER DIGITAL SIGNAL PROCESSOR SLOT1 +3.3V(P)
Page 61: Main Block (2 Of 2) Diagram
TH-103PF12E 11.3. Main Block (2 of 2) Diagram DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DATA DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER DRIVER...
Page 62: Block (1 Of 8) Diagram
TH-103PF12E 11.4. Block (1 of 8) Diagram DVI-D INTERFACE JK3302 AUDIO IN Q3302 AUDIO_R DS12 AUDIO_L AUDIO_L AUDIO OUT L AUDIO_R Q3303 AUDIO OUT R FACTORY IC3303 PLUG DET 5V<->3.3V +15V D3025 SDA/SCL +15V STB+5V +15V +3.3V IC3345 STB+5V TA1+...
Page 63: Block (2 Of 8) Diagram
TH-103PF12E 11.5. Block (2 of 8) Diagram SLOT INTERFACE/SYNC PROCESSOR/SOUND PROCESSOR DS11 +3.3V(P) SLOT3.3V +5V(P) SLOT5V +9V(P) SLOT9V +15V(P) SLOT15V +14V(LAN) LAN14V +5V(STB) STB5V AUDIO IN L AUDIO IN R VD_1 HD_1 PR_1 PR/R PB_1 PB/B SLOT1 S2_1 Q8021-23 RXD_S1...
Page 64: Block (3 Of 8) Diagram
TH-103PF12E 11.6. Block (3 of 8) Diagram SLOT INTERFACE/SYNC PROCESSOR/SOUND PROCESSOR +9V(P) +3.3V(P) AUDIO OUT +3.3V(P) +5V(P) AUDIO OUT TERMINALS +5V(P) TERMINAL +9V(P) L LINE OUT JK8501 +15V(P) LAN+14V R LINE OUT +14V(LAN) +5V(STB) IC804 +1.8V(P) +1.8V A_OA+- - OE+-...
Page 65: Block (4 Of 8) Diagram
TH-103PF12E 11.7. Block (4 of 8) Diagram +2.5V DIGITAL SIGNAL PROCESSOR FACTORY LVDS RECEIVER & TTL PARALLEL +2.5V R/G/B 30bit ASIC OUT A SCW IN A A_OA+- - OE+- LVDS IC4513 A_EA+- - EE+- PARALLEL PI1R0-R9 PI1D(0)-(9) RECEIVER PI1D(0)-(29) 30bit...
Page 66: Block (5 Of 8) Diagram
TH-103PF12E 11.8. Block (5 of 8) Diagram Q601,Q602 COLD COLD P(SUB) POWER SUPPLY(SUB) Q610,Q611 Q201,Q202 L604,L605 F201 T201 Vsus RESONANCE Vsus 5A 250V IC202 D254-D257 IC601 COMPARATOR IC201 IC251 Q605-Q608 D206 PC201 Vsus D653,654 PFC CONTROL Vsus Vsus POWER PHOTO COUPLER...
Page 67: Block (6 Of 8) Diagram
TH-103PF12E 11.9. Block (6 of 8) Diagram FORMAT CONVERTER, PLASMA AI PROCESSOR FACTORY IC9500 DISCHARGE CONTROL IC9503 FACTORY FLASH DISCHARGE CONTROL DATA DRIVER CONTROL DATA SCAN CONTROL +2.5V IC9002 IIC3 C31(UPPER) SUSTAIN CONTROL TENP SENSOR +3.3V +3.3V(P) VIDEO DATA +1.2V +3.3V(P)
Page 68: Block (7 Of 8) Diagram
TH-103PF12E 11.10. Block (7 of 8) Diagram SUSTAIN CONNECTOR (UPPER) SCAN DRIVE SC50 FACTORY P(MAIN_1) TPVSUS Vsus TPVSET IC16791 VSET GEN. 16V-F SHUNT REG SUSTAIN DRIVE DC/DC CONVERTER IC16788,89 Q16604 PC16601 P(MAIN_2)P11 TPVSUS CPH2 VF_GND PHOTO COUPLER Vsus SCAN OUT (UPPER)
Page 69: Block (8 Of 8) Diagram
TH-103PF12E 11.11. Block (8 of 8) Diagram PANEL DRIVER PANEL DRIVER PLASMA PANEL PANEL DRIVER PANEL DRIVER PLASMA PANEL PANEL DRIVER PANEL DRIVER IC17201 IC17301 IC17401 IC17501 CONTROL CONTROL DATA DATA BUFFER BUFFER BUFFER BUFFER VIDEO VIDEO DATA DATA VIDEO...
Page 70 TH-103PF12E...
Page 71: Wiring Connection Diagram
TH-103PF12E 12 Wiring Connection Diagram 12.1. Wiring (1)
Page 72: Wiring (2)
TH-103PF12E 12.2. Wiring (2)
Page 73: Wiring (3)
TH-103PF12E 12.3. Wiring (3)
Page 74: Exploded View And Replacement Parts List
Model No. : TH-103PF12E Important Safety Notice...
Page 75 Model No. : TH-103PF12E Exploded View...
Page 76 Model No. : TH-103PF12E Side Power part location...
Page 77 Model No. : TH-103PF12E Cabinet part location...
Page 78 Model No. : TH-103PF12E Fan part location...
Page 79 Model No. : TH-103PF12E Rear cover location...
Page 80 Model No. : TH-103PF12E Duct Barriers...
Page 81 Model No. : TH-103PF12E Printed Circuit Board...
Page 82 Model No. : TH-103PF12E Cable relation...
Page 83 Model No. : TH-103PF12E Packing summary (1)
Page 84 Model No. : TH-103PF12E Packing summary (2)
Page 85 Model No. : TH-103PF12E Packing summary (3)
Page 86 Model No. : TH-103PF12E Packing summary (4)
Page 87 Model No. : TH-103PF12E Packing summary (5)
Page 88 Model No. : TH-103PF12E Packing summary (6)
Page 89 Model No. : TH-103PF12E Packing summary (7)
Page 90 Model No. : TH-103PF12E Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks EUR7636090R REMOTE CONTROL J0KF00000021 FILTER K2CN3YY00003 AC CORD (E) K2CT3YY00002 AC CORD (B) L6FAYYYH0030 FAN UNIT (80) L6FAYYYH0031 FAN UNIT (120) MD103F12S1J PLASMA DISPLAY PANEL...
Page 91 Model No. : TH-103PF12E Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks TMKY910 DUCT BARRIER F TMKY911 DUCT BARRIER G TMKY912 DUCT BARRIER H TMKY914 DUCT BARRIER J TMKY915 DUCT BARRIER K TMKY916 DUCT BARRIER L...
Page 92 Model No. : TH-103PF12E Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks TPDA1419 CUSHION (CENTER) TPDF1746 ACCESSORIES BOX TPDX0007 JOINT TPDX0027 BOTTOM SKID TPDX0041 BAND TPEH323 PROTECTION BAG TPEH324 FRONT PROTECTION COVER TQB0E0896A INSTRUCTION BOOK(GERMAN) 1 PAVCCZ...
Page 93 Model No. : TH-103PF12E Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks TTUA1779-1 REAR COVER (R) ASSY 1 PAVCCZ TTUA2317 REAR COVER (L) ASSY TUWC056 SIDE POWER COVER TUXJ350 CABINET JOINT METAL (A) 2 （ LEFT/TOP RIGHT/BOTTOM ）...
Page 94 Model No. : TH-103PF12E Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks XZBT6506 POLY BAG (INSTRUCTION BOOK) ETX2MM780MG CIRCUIT BOARD P (MAIN) ETX2MM780MGA CIRCUIT BOARD P (SUB) TNPA4084 CIRCUIT BOARD S1 TNPA4085 CIRCUIT BOARD V1 TNPA4086...

Panasonic TH-103PF12E Service Manual

1 Safety Precautions

2 Warning

3 Service Navigation

4 Specifications

5 Operating Instructions

6 Service Mode

7 Troubleshooting Guide

8 Service Fixture & Tools

9 Disassembly and Assembly Instructions

10 Measurements and Adjustments

11 Block Diagram

12 Wiring Connection Diagram

13 Exploded View and Replacement Parts List

Quick Links

TABLE OF CONTENTS

Related Manuals for Panasonic TH-103PF12E

Summary of Contents for Panasonic TH-103PF12E

Table of Contents