Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Phantom PMR-GP1
Summary of Contents for Phantom PMR-GP1
- Page 1 Operating Guide PMR-GP1 Table of Contents Introduction Features Installation - GP1 Installation - HH1 Operation Tips & Troubleshooting Chart of Mic Sensitivities Specifications Warranty PMR-HH1 MADE IN USA PATENT PENDING...
- Page 3 Congratulations on getting your new Phantom Mic Rider! This operating guide covers the use of both models of the Phantom. Follow the directions that apply to your model. For your convenience each section of this guide is marked as follows indicating which model is explained.
- Page 4 • One small Phillips screwdriver for removing the security cover. • One plastic programming Phantom Tool. • This Operating Guide • One Phantom Mic Rider with built-in IR sensor • One small Phillips screwdriver for removing the security cover. • One plastic programming Phantom Tool.
-
Page 5: Features
Features Your new Sabine Phantom Mic Rider is the first phantom-powered DSP unit that provides these five powerful features: • FBX Feedback Exterminator Increases gain before feedback • Automatic Gain Control Helps maintain level as you move toward and away from the mic. -
Page 6: Operation
LED turn green indicating phantom power is present. 3. Plug the microphone into the top of the Phantom. Plug in the IR Sensor and connect the cable to the gooseneck using the supplied clips, as shown in Figure 2. For best results... - Page 7 FIGURE 1 FIGURE 2 Connecting IR Sensor cable Installing the Phantom...
- Page 8 2. Turn the body of the Phantom one half turn counter-clock- wise – no more! 3. Tighten the set screws on both sides of the Phantom case and be sure they seat into the connector - just like they did...
- Page 9 Installing the Phantom Changing the Orientation of the Phantom FIGURE 3 If the Phantom mounts like this, then loosen the Allen screws as described on the previous page. Turn the Phantom no more than 1/2 half turn counter-clockwise. Tighten the screws and the Phantom will be properly oriented.
- Page 10 Phantom. Working below the podium or table, remove audio cable from the mic. 2. Mount the Phantom below the table using Velcro or tie wraps; plug in the IR sensor cable and run that out to the front edge of the table or podium, as shown in Figure 4.
- Page 11 Installing the Phantom Below the table or podium FIGURE 4 IR sensor and cable To mixer...
-
Page 12: Handheld Microphones
(Refer to Figure 5 on next page) 1. Mute the audio channel for the handheld microphone you have selected to use with the Phantom. Remove the audio cable from the mic. 2. Plug the Phantom (PMR-HH1) into the microphone as shown at right, and reconnect the audio cable. - Page 13 Installing the Phantom Handheld microphones IR sensor FIGURE 5...
-
Page 14: Operating The Phantom
LED Indicator: The 3-color LED lights green when the Phantom is connected to phantom power and the mic is on. When programming the Proximity and Sensitivity controls the LED flashes red in groups of 1, 2, or 3 flashes to indicate the chosen setting. Once the LED stops flashing the value is set. - Page 15 Operating the Phantom The Phantom is designed to be ready to go in a minute or two. First you will set the Phantom’s microphone sensitivity to match your microphone, then your FBX Feedback Exterminator filters, and you can even make an adjustment to the Proximity Effect and Plosive controllers.
- Page 16 2. Using the Phantom Tool press and hold the FBX button for three seconds. The amber LED will flash continuously when you have held it long enough. Let go of the button. The LED continues to flash.
- Page 17 Operating the Phantom FBX Setup (continued) is in setup mode. The Phantom’s first FBX filter will engage and re- move the tone. The flash rate of the LED increases with every filter that is placed. Raise the gain again until you hear another feedback tone.
- Page 18 Operating the Phantom Proximity & Plosive Control Setup 1. Make sure the Phantom is installed as described in “In- stalling the Phantom” previously. 2. Using the Phantom Tool, press the PROX button mo- mentarily and you will see the red LED flash. This indicates the current setting.
- Page 19 The clip slides on as shown at right. Mount that assembly to the gooseneck. 2. Plug the cable into the Phantom’s jack and clip the cable neatly to the gooseneck using the clips shown in Figure 2 on page seven.
- Page 20 LED turning off. 5. You can disable this Gate function by simply unplugging the sensor’s jack from the Phantom. The LED will now be green. 6. You can also disable the IR Gate by removing the secu- rity cover and pushing the IR button for 3 seconds.
-
Page 21: Tips And Troubleshooting
Phantom is installed and powered up, the sensor will not function (the mic is always on) for about 18 seconds. If you plug in the sensor first, then power the Phantom, the sensor works immediately. 4. The FBX may only set 2 filters. This is normal. The Phantom will provide between two and four FBX filters depending on system acoustics. - Page 22 Microphone Sensitivity Charts (see instructions on page 15) Audio-Technica Current (mA) SEN Level SEN Setting Model Type Sensitivity (dB) Voltage (V) AT808G dynamic ATR3M dynamic ES905/C electret 11-52V ES905/H electret 11-52V ES905/ML electret 11-52V ES915/C electret 11-52V ES915/H electret 11-52V ES915/ML electret 11-52V...
- Page 23 Beyer Voltage (V) Current (mA) SEN Level SEN Setting Model Type Sensitivity (dB) SHM 201 A electret 11-52V 3.5mA SHM 201 A ZSH electret 11-52V 3.5mA SHM 201 AS electret 11-52V 3.5mA SHM 201 AS ZSH electret 11-52V 3.5mA SHM 203 A electret 11-52V 3.5mA...
- Page 24 11-52V Check the manufacturer’s web site for the most current sensitivity specifications for your microphone; set your Phantom’s SEN setting based on the examples in the charts above. Use this space to record information about your microphone Make: _______________________...
-
Page 25: Specifications
Specifications • Minimum phantom power requirement: 12V @ 9 mA. • Supplies 12 to 17V and up to 4 mA of phantom power to connected mic • Frequency Response: +/-1.5dB (50Hz to 20kHz) • Dynamic Range: 94dB typ (unweighted) • Distortion: < 0.5% @ 1kHz •... -
Page 26: One-Year Limited Warranty
ONE-YEAR LIMITED WARRANTY: THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO WAR- RANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY. ONE-YEAR LIMITED WARRANTY SABINE, INC. - Page 27 pressed have been complied with, Sabine will provide the necessary warranty service to repair or replace the product and will return it, FREIGHT COLLECT, to you, the purchaser. Sabine’s liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual damages up to the greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action.
- Page 28 Register your Sabine products online at: www.Sabine.com and FBX Feedback Exterminator are registered trademarks of Sabine, Inc., and are the ® ® brand names of its line of automatic feedback controllers. Covered by U.S. Patent No. 5,245,665, Australian Patent No. 653,736, Canadian Patent No. 2,066,624-2, German Patent No. 69118486.0, and British Patent No.
Need help?
Do you have a question about the PMR-GP1 and is the answer not in the manual?
Questions and answers