Product Specifications - HPE 2530 Quick Setup Manual

CAUTION:
Ensure the power source circuits are properly grounded, then use the power cord supplied with
the switch to connect to the AC power source.
If your installation requires a different power cord than the one supplied with the switch and/or
power supply, be sure the cord is adequately sized for the switch's current requirements. In
addition, be sure to use a power cord displaying the mark of the safety agency that defines the
regulations for power cords in your country/region. The mark is your assurance that the power
cord can be used safely with the switch and power supply.
When installing the switch, the AC outlet should be near the switch and should be easily
accessible in case the switch must be powered off.
Ensure the switch does not overload the power circuits, wiring, and over-current protection. To
determine the possibility of overloading the supply circuits, add together the ampere ratings of
all devices installed on the same circuit as the switch and compare the total with the rating limit
for the circuit. The maximum ampere ratings are usually printed on the devices near the AC
power connectors.
Do not install the switch in an environment where the operating ambient temperature exceeds
its specification.
Ensure the air flow around the switch is not restricted. Leave at least 7.6 cm (3 inches) for
cooling. For the air flow direction, see the Installation and Getting Started Guide for your product,
located on the HPE Networking web site at http://www.hpe.com/networking/support.
For additional safety and regulatory information, and switch recycling information, refer to the safety and
regulatory documentation on the Hewlett Packard Enterprise website at
Safety-Compliance-EnterpriseProducts, and to the HPE 2530 Switch Installation and Getting Started
Guide that can be found on the Hewlett Packard Enterprise Networking website:
networking/support.
For important safety, environmental, and regulatory information, see Safety and Compliance Information
for Server, Storage, Power, Networking, and Rack Products, available at
Safety-Compliance-EnterpriseProducts.

Product Specifications

1
Electrical:
AC voltage:
Maximum current:
Frequency range:
Acoustics:
2530-24G Switch 2530-48G Switch
(J9776A) (J9775A)
100-127 V / 100-127 V /
200-240 V 200-240 V
0.60 A / 0.37 A 1.20 A / 0.68 A
50 / 60 Hz 50 / 60 Hz
Geraeusch emission Geraeusch emission
LpA=34.0 dB am LpA=34.5 dB am fiktive
fiktiven Arbeitsplatz Arbeitsplatz nach DIN
nach DIN 45635 T.19 45635 T.19
Noise Emission Noise Emission
LpA=34.0 dB at virtual LpA=4.5 dB at virtual
workspace according to workspace according to
DIN 45635 T.19 DIN 45635 T.19
http://www.hpe.com/support/
http://www.hpe.com/
http://www.hpe.com/support/
2530-24G-PoE+ Switch 2530-48G-PoE+ Switch
(J9773A) (J9772A)
100-127 V / 100-127 V /
200-240 V 200-240 V
3.20 A / 1.60 A 5.80-4.50 A / 2.90-2.40
A
50 / 60 Hz 50 / 60 Hz
Geraeusch emission Geraeusch emission
LpA=43.9 dB am LpA=43.6 dB am fiktiven
fiktiven Arbeitsplatz Arbeitsplatz nach DIN
nach DIN 45635 T.19 45635 T.19
Noise Emission Noise Emission
LpA=43.9 dB at virtual LpA=43.6 dB at virtual
workspace according to workspace according to
DIN 45635 T.19 DIN 45635 T.19