Table of Contents
Advertisement
Quick Links
HPE 2530 24-Port and 48-Port Switches
Quick Setup Guide
The switch drawings in this document are for illustration only and may not match your particular switch
model.
For more detailed instructions and information to set up your switch, view or download the Installation
and Getting Started Guide for your switch at http://www.hpe.com/networking/support.
1. Unpack and check included parts.
2.
Prepare for installation. To avoid personal injury or product damage, review
Information for HPE 2530 24/48-Port Switches" (page
3. Power on and verify that Self-Test completes normally. The switch does not contain a power switch. It is powered on
by connecting power cord through the AC power cord
*5900-4853*
© Copyright 2013, 2015 Hewlett Packard Enterprise Development LP
The information in this document is subject to change without notice.
Part Number: 5900-4853
Published: November 2015
Documentation kit
Switch
Console port serial cable (DB-9 to RJ-45)
Accessory kit (installation hardware)
AC power cord
4).
"Safety and Regulatory
Advertisement
Table of Contents
Related Manuals for HPE 2530
Summary of Contents for HPE 2530
-
Page 1: Quick Setup Guide
The switch drawings in this document are for illustration only and may not match your particular switch model. For more detailed instructions and information to set up your switch, view or download the Installation and Getting Started Guide for your switch at http://www.hpe.com/networking/support. 1. Unpack and check included parts. Documentation kit... - Page 2 The HPE 2530 24-port and 48-port switches can also be mounted in 4-post racks and cabinets by using the HPE X410 Switch Rail Kit (J9583A). For instructions on using the kit, see the documentation that is included with the kit.
-
Page 3: Sfp Installation Notes
6. Connect network cables. NOTE: For transceiver connections, install and use only HPE SFP transceivers supported by the switch. “SFP Installation Notes” (page 7. (Optional) Configure the switch for management. By factory default, the switch will automatically obtain its IP network configuration from a DHCP or BootP server. -
Page 4: Installation Precautions
Environmental limitations. If using SFPs with the switch, ensure that the operating temperature range at the switch installation site does not exceed the range allowed for the SFP. Safety and Regulatory Information for HPE 2530 24/48-Port Switches To avoid personal injury or product damage when installing your switch, read the installation precautions and guidelines below. -
Page 5: Product Specifications
For additional safety and regulatory information, and switch recycling information, refer to the safety and regulatory documentation on the Hewlett Packard Enterprise website at http://www.hpe.com/support/ Safety-Compliance-EnterpriseProducts, and to the HPE 2530 Switch Installation and Getting Started Guide that can be found on the Hewlett Packard Enterprise Networking website: http://www.hpe.com/ networking/support. - Page 6 DIN 45635 T.19 DIN 45635 T.19 The HPE 2530 switches automatically adjust to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz. All HPE 2530 24-Port and 48-Port Switches Environmental: Operating Temperature: 0°C to 45°C (32°F to 113°F)
-
Page 7: Power Cord
8120-5334 United States/Canada/Mexico 8120-6805 8121-0973 The power cord for the HPE 2530-48-PoE+ and HPE 2530-48G-PoE+ Switches supports a higher amperage and uses a C15 connector. Japan Power Cord Warning: Important Note for the 2530-PoE+ Switches For PoE/PoE+ information see the HPE Power over Ethernet (PoE/PoE+) Planning and Implementation Guide on the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/support. -
Page 8: Regulatory Information
Documentation Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document title, part number, edition, and publication date located on the front cover of the document. For online help content, include...