Advertisement
6.13. Customer function / deactivation of signal sound:
General information
The function deactivation of the signal sound does not exist
generally and must be programmed in the software
variant.
w Deactivation resp. activation of the signal sound is executed
in all designs and key arrangements analogously.
w For that you always have to use keys S1, S2, S3 and S4
independent of their variant-depending program load.
w The key S4 is ALWAYS the "signal sound deactivation key"
w The signal sound at the cycle end is always set active
by the manufacturer.
w If the signal sound is deactivated it means that in general
no acoustic end signal will sound any more.
The acoustic fault signals also cannot be heard any more!
vertical key arrangement
S1
LD1
LD4
S4
On/Off
1. 9 9
LD2
S2
LD3
S3
horizontal key arrangement
LD1
LD2
LD3
LD4
1. 9 9
S1
S2
S3
S4
On/Off
Table for indication of condition on/off:
indication
display
"END"-LED
if no display available
depending on variant
1b
on
0b
off
Calling / changing / saving the signal sound deactivation
1.
S1
LD1
On/Off
LD2
S2
LD3
S3
LD1 is lit / LD2 - LD4 flashing
2.
S1
LD1
On/Off
S2
LD2
LD3
S3
LD1 is lit / LD2 flashing
3.
S1
LD1
On/Off
LD2
S2
LD3
S3
LD1 is lit / LD2 flashing
4.
S1
LD1
On/Off
LD2
S2
LD3
S3
LD1 is lit / LD2 flashing
5.
S1
LD1
On/Off
LD2
S2
LD3
S3
END
S1
LD1
LD4
On/Off
LD2
S2
LD3
S3
END
... automatically Off after 60 seco
comment
signal sound (buzzer) on
signal sound (buzzer) off
LD4
S4
END
LD4
S4
END
if no display
LD4
S4
available:
1b
END
if no display
LD4
S4
available:
0b
END
if no display
LD4
S4
available:
1b
END
S4
S1
LD1
LD4
S4
On/Off
LD2
S2
LD3
S3
... Off by actuating On/Off manually
Generally, no wash cycle may be selected when calling the customer functions!
ATTENTION: In case of reduced key assemblies be sure to observe Description Page B 1.
Calling the function "deactive signal sound"
1.
Switch on appliance with ON/OFF key S1
LD1 display with ON/OFF key is lit.
2.
Press keys S2 and S3 simultaneously until the
confirmation LEDs LD2, LD3 and LD4 are flashing
LD1 display with ON/OFF key is lit.
3.
By actuating the function key S4 you now can call
the function signal sound deactivation. The confirmation
LED LD4 continues flashing, LEDs LD2 and LD3 go out.
The current condition whether the signal sound is active
or not is indicated in the display.
If there is no display available depending on variant, the
value is indicated by the "END" LED.
(see for that the table on the left side of this page!)
Deactivation resp. activation of the signal sound:
4. / 5. By any further actuation of the function key S4 you can
activate resp. deactivate the signal sound alternating.
Leaving the function
After the last key pressure of function key S4 you can
leave the special program as follows.
After 60 seconds all displays go out automatically,
except LD1 of the ON/OFF key
or
the appliance is switched off by the ON/OFF key S1.
Saving the set condition
The condition is saved directly after any entry.
Advertisement
