Advertisement
6.12. Customer function / deactivation of rinse-aid addition:
General information
The function rinse-aid deactivation does not exist generally
and must be programmed in the software variant.
w Deactivation resp. activation of rinse-aid addition is executed
in all designs and key arrangements analogously.
w For that you always have to use keys S1, S2 and S3
independent of their variant-depending program load.
w The key S3 is ALWAYS the "rinse-aid deactivation key"
w The rinse-aid addition is always set active by the manufacturer.
w If the rinse-aid addition is deactivated it means that no more
rinse-aid is added via the detergent dispenser.
w Along with the deactivation, a variant-depending existing
"rinse-aid" LED is deactivated generally.
vertical key arrangement
S1
LD1
LD4
S4
On/Off
1. 9 9
LD2
S2
LD3
S3
horizontal key arrangement
LD1
LD2
LD3
LD4
1. 9 9
S1
S2
S3
S4
On/Off
Table for indications of condition on/off:
indication
display
"END"-LED
if no display available
on variant
1d
on
0d
off
Calling / changing / saving the rinse-aid addition deactivation
1.
LD1
LD2
LD3
LD1 is lit / LD2 - LD4 flashing
2.
LD1
LD2
LD3
LD1 is lit / LD2 flashing
3.
LD1
LD2
LD3
LD1 is lit / LD2 flashing
4.
LD1
LD2
LD3
LD1 is lit / LD2 flashing
5.
LD1
LD2
LD3
END
LD1
S1
On/Off
LD2
S2
END
LD3
S3
... automatically Off after 60 sec
comment
rinse-aid addition on
rinse-aid addition off
S1
LD4
S4
On/Off
S2
S3
END
S1
LD4
S4
On/Off
S2
END
S3
S1
if no display
LD4
S4
Ein/Aus
available:
1d
S2
S3
END
S1
if no display
LD4
S4
On/Off
available:
0d
S2
S3
END
S1
if no display
LD4
S4
On/Off
available:
1d
S2
S3
END
LD4
S4
S1
LD1
LD4
S4
On/Off
LD2
S2
LD3
S3
... Off by actuating On/Off manually
Generally, no wash cycle may be selected when calling the customer functions!
ATTENTION: In case of reduced key assemblies be sure to observe Description Page B 1.
Calling the function "deactivate rinse-aid addition"
1.
Switch on appliance with ON/OFF key S1.
LD1 display with ON/OFF key is lit.
2.
Press keys S2 and S3 simultaneously until the
confirmation LEDs LD2, LD3 and LD4 are flashing
LD1 display with ON/OFF key is lit.
3.
By actuating the function key S3 you now can call the
function rinse-aid addition. The confirmation LED LD3
continues flashing, LEDs LD2 and LD4 go out.
The current condition whether the rinse-aid addition is
active or not is indicated in the display. If there is no
display available depending on variant, the value is
indicated via the "END" LED.
(see for that the table on the left side of this page!)
Deactivation resp. activation of rinse-aid addition:
4. / 5. By any further actuation of the function key S3 you can
activate resp. deactivate the addition alternating.
Leaving the function
After the last key pressure of function key S2 you can
leave the special program as follows.
After 60 seconds all displays go out automatically,
except LD1 of the ON/OFF key
or
the appliance is switched off by the ON/OFF key S1.
Saving the set condition
The condition is saved directly after any entry.
Advertisement
