Setting Up / Operation - Stadler Form EVA Operating Instructions Manual

Setting up / operation

1. Put Eva in the desired location on a flat surface. The mist reaches a
height of up to 4 ft 7 in / 1.4 m thanks to the high-performance humidifi-
cation (output level 5, warm mode on). This makes it possible to place
Eva directly on the floor. Connect the power cord (1) to a suitable socket.
2. Take the Remote Sensor
the packaging. Open the battery compartment (4) on the underside of
the Remote Sensor
batteries into the battery compartment (4), as shown on page 4, and
close the lid again. Now place the Remote Sensor
3. On the one hand, the Remote Sensor
guarantees precise humidification by its external position. On the other
hand, the Remote Sensor
tion the humidity sensor Remote Sensor
on a table or a sideboard with an optimal distance from Eva between
10 – 16 ft / 3 – 5 m. The Remote Sensor
in the room so that the room air can flow past the sensor (5) as freely as
possible. If this is not possible, we recommend positioning the Remote
Sensor with a minimum distance of 1 ft / 30 cm from the wall and a
TM
minimum distance of 6 ft / 2 m from windows and ventilation openings.
4. Remove the water tank (6) by holding it by the handle and pulling it
up. Screw off the water tank lid (7) and fill the water tank with clean,
cold tap water up to the maximum mark. Make sure that the anticalc
cartridge (8) has been soaked in water for 24 hours prior (see "Before
setup"). Finally, screw the lid (7) back on the water tank (6). Then place
the water tank (6) in the unit. The water tray (9) will now slowly fill from
the water tank. Important: please do not move the appliance when it is
filled with water. The water could run into the electronics.
5. Press the on/off button (10) to switch Eva on. The current relative humid-
ity in % is shown on the display (15). If the water level indicator light (16)
is red, there is too little water in the unit. The humidification output level
is pre-set to level 2 and the desired humidity at 45 %.
6. Activate the Remote Sensor
(11a). The humidity sensor automatically sends information about the
measured relative humidity several times per minute to the unit, which
shows it on the display (15). The measurement can also be activated by
pressing any button on the Remote Sensor
button (10)).
7. The desired humidity can be changed by pressing the "Hygrostat" but-
ton (11) several times (35 – 75 % and continuous operation "CO"). The
symbol on the display (15) blinks during input. After a few seconds with-
out input, the selected value is saved. The symbol changes to the current
measured humidity.
8. The humidification performance can be changed by pressing the "Out-
put" button (12) several times (levels 1 – 5). The level is indicated on the
display (15) by horizontal bars (e.g. 1 bar = level 1).
9. By pressing the "Warm" button (13), the warm mode, and with it the
water pre-heating, is turned on. Now the LED on the "Warm" button
on the unit is on. The heating plate (17) warms the water before it is
turned to mist by the ultrasonic membrane (19). The warm mode creates
a pleasantly warm mist plus increases the humidification performance.
(2), the stand (3) and the two batteries out of
TM
(2) by turning the lid anticlockwise. Insert the two
TM
(2) also serves as a remote control. Posi-
TM
(2) by pressing the "Hygrostat" button
TM
(2) on the stand (3).
TM
(2) is a humidity sensor and
TM
(2) in the centre of the room
TM
should be positioned centrally
TM
(2) (aside from the on/off
TM