Daikin DCG090XXX3BXXX Technical Manual page 12

PACKAGE GAS SPECIFICATIONS
COOLING COOLING CAPACITY, BTUH
CAPACITY EER/IEER
HEATING HEATING IN PUT
CAPACITY HEATING OUTPUT
STEADY STATE EFFY %
TEMPERAT URE RISE (°F)
UNIT
VOLTAGE (NAMEPLATE)
ELECTRIC AL UNIT AMPS (TOTAL)
SPECIFICATION MINIMUM CIRCU IT AMPACITY
MAXIMUM OVER CURRENT PROTECTION
HEATING NUMBER OF BU RNER S
SECTION OR IFICE SIZE NATURAL
OR IFICE SIZE LP
PRESSURE SWITCH SETTING
TYPE
COMPRESSOR
RATED LOAD AMPS
LOCKED ROTOR AMPS
QU ANTITY OF CON DENSER FAN MOTORS
CONDENSER
FAN MOTOR HORSEPOWER
RPM
RATED LOAD AMPS
LOCKED ROTOR AMPS
CONDENSER FAN
BLADE DIAMETER ( ") / # OF BLADES
NOMINAL C FM
CONDENSER FACE AREA - SQ. FT.
COIL NUMBER OF ROWS
FINS PER INC H
EVAPORATOR HORSEPOWER - TYPE - STANDARD
BLOWER NO. OF SPEEDS
MOTOR RATED LOAD AMPS
LOCKED ROTOR AMPS
MOTOR SPEED TAP - COOLIN G
RPM
EVAPORATOR DIAMET ER X WIDTH (INCHES)
BLOWER RATED SCFM COOLING
MAX EXTERNAL STATIC PRESS ("w.c.)
FACE AREA - SQ. FT.
EVAPORATOR
NUMBER OF ROWS
COIL
FINS PER INC H
PRIMAR Y LIMIT SETTING (°F)
HEATING
LIMITS AUXILIARY LIMIT SETTING (°F)
ROLLOUT LIMIT SETTING (°F)
GENERAL FILTER SIZE
INFORM ATION DRAIN SIZE (IN CHES)
EXPANSION DEVIC E
REFRIGERANT CHARGE R-410A (Oz.) CIR #1
REFRIGERANT CHARGE R-410A (Oz.) CIR #2
POWER SUPPLY ENTRANCE SIZE (INCHES)
LOW VOLTAGE ENTRANCE SIZE (INCHES)
LOW PRESSURE SWITCH (OPEN/CLOSE-PSIG)
HIGH PRESSURE SWITCH (OPEN S-PSIG)
SHIPPING WEIGHT LBS.
OPERATIN G WEIGHT LBS.
Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
(1)
(2) Rated capacity 350 CFM/Ton, full capacity 400 CFM/Ton
*** NOTE: High static airflow requires installation of high static kit (HSKT*).
Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes.
Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information.
IMPORTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers
in accordance with the National Electrical Code and/or all local codes. Data shown is w/o electric heaters.
12
DC G090***4B*** D CG102***4B***
A*
90,000 102,000
11.5/11.5 11.3/11.5
210,000 210,000
168,000 168,000
80
35 - 65 35 - 65
460/3/60 460/3/60
16.3
18
(1)
20
6
34
52
0.34
SCROLL SCROLL
6.1
41.0
2
1/4
890 1075
0.8
1.72
22/4
7,200 8,200
28.8
2 X 2 2 X 2
27 +/-1 27±1
1.5 - STD STATIC BELT 2.0 - STD STATIC
D RIVE BELT D RIVE
1
2.5
16.4
---
1745 1725
15X12 15x15
3000 3200
1.0
8.9
4
16
200
150
350
(4) 16 X 20 x 2 (4) 16 X 24 x 2
3/4"
Orifice (0.076) Orifice (0.080)
100
100
Locating Dimple Locating D imple
Locating Dimple Locating D imple
22/50 22/50
660
1175 1215
1100 1140
DCG090-150XXX4*XXXA*
DC G120***4B*** DCG120***4V***
A* A*
116,000
11.3 / 11.5
210,000
168,000
80 80
25 - 55
460/3/60
18.9 22
20.5 24
25 30
6 6
34 34
52 52
0.34 0.34
SC ROLL
6.3 7.8
55 52
2 2
1/3 1/3
1075
1.2 1.2
2.6 2.6
22/3 22/3
8,200
35.2 35.2
2 X 2
27 +/-1
2.0 - STD STATIC 2.0 - ST D STATIC
BELT DRIVE BELT DRIVE
1 1
3.9 3.9
40 40
--- ---
1725
15X15
3500
1.0 0.9
10.2 10.2
4 4
14 14
190 200
180 160
350 350
(4) 16 X 24 x 2 (4) 16 X 24 x 2
3/4" 3/4"
Orifice (0.086) Orifice (0.086)
115 125
115 125
Locating Dimple Locating Dimple
Locating Dimple Locating Dimple
22/50
660 660
1215
1140
D CG150***4B***
A* A*
116,000 144,000
11.3 / 12.8 10.8 / 11.0
210,000 210,000
168,000 168,000
80 80
25 - 55 15 - 45
460/3/60 460/3/60
21 28
23 31
30 40
6 6
34 34
52 52
0.34 0.34
SCROLL SCROLL
7.8 10.6
52 75
2 2
1/3 1/3
1075 1075
1.2 1.2
2.6 2.6
22/3 22/3
8,200 7,200
35.2 39
2 X 2 2 X 2
27 +/-1 27 +/-1
3.0 - STD STATIC
BELT D RIVE
2 1
3 / 1.9 4.7
21.5 / 9.1 66
--- ---
1750 / 1165 1725
15X15 15X15
3500 3900
0.9 0.9
10.2 14.7
4 4
14 15
200 180
160 160
350 350
(4) 20 X 25 x 2
3/4" 3/4"
Orifice (0.092)
125 175
125 175
Locating Dimple
Locating Dimple
22/50 22/50
660 660
1215 1340
1140 1315