Door Reversal - Kenmore 461.99100 Owner's Manual

Door Reversal

TOOLS REQUIRED
Phillips #2 screwdriver and an adjustable wrench.
WARNING!
Excessive Weight Hazard
Use two or more people when moving the beverage
centre.
1. Unplug the beverage centre, empty all of its contents
and carefully lay the unit on its back.
2. Unscrew the two leveling legs; one from the
bottom hinge on right (Fig. 4) and one from the left
side of the unit (Fig. 5).
3. Remove the bottom hinge by unscrewing its three (3)
screws (Fig. 3).
NOTE: Keep this hinge in a safe place incase
you need to return to a right hand door swing.
4. Carefully remove the door and set aside by sliding
it downward off of the top hinge pin (Fig.2).
5. Remove the two (2) plastic screw caps located on top
of the hinge cover (Fig. 2).
6. Remove the top hinge cover by removing its two (2)
screws (Fig. 2).
7. Remove the top hinge by unscrewing its three (3)
screws (Fig. 2)
8. Remove the plastic door pin cap from the top left
side of the door and transfer it to the right side of the
door (Fig.7).
9. Remove the three (3) Plastic Screw Caps from the
top left side of the cabinet and transfer them to the
top right side of the cabinet (Fig.1).
10. Install the top hinge on the top left side of the unit
(Fig.2).
11. Carefully install the door on the cabinet (insert upper
door into top hinge pin).
7 Left Bottom Hinge
Door Pin Cap 6
(supplied)
A
B
C
D
A. Washers
B. Hinge pin
C. Bottom hinge
D. Bottom hinge screws
12. Using the left-side bottom hinge supplied with your
unit (Fig.6): insert the hinge pin into the bottom of the
door, then align the holes in the hinge with the holes
in the cabinet and secure hinge to cabinet with three
(3) screws.
13. Install the leveling leg formerly attached to the
right bottom hinge (Fig.4) onto the new left bottom
hinge, and install the leveling leg from the former
left side position into the right side position (Fig.5).
14. Check door alignment, door seal and ensure the door
lock slides comfortably into the lock chamber. Tighten
all hinge screws.
I M P O R TA N T !
Allow the unit to stand upright for at-least 1 hour
before putting the unit into operation.
1
A
Top Hinge
A. Plastic screw caps
A. Hinge cover screw
caps
B. Hinge cover screws
C. Hinge cover
D. Top hinge screws
E. Top hinge
F. Top hinge pin
Right Bottom Hinge
4
5 Leveling Leg for
Leveling Leg
A. Washers
Bottom Hinge
B. Hinge pin
C. Bottom hinge
D. Bottom hinge screws
8
Características de su
Centro de Bebidas
2
A
B
C
D
1. Indicador y controles electrónicos : Para
E
ver la temperatura actual del Conservador
F
de Bebidas y para graduarla.
2. Trabas con llave a prueba de niños.
3. Conmutador para la luz interior : Para
encender y apagar manualmente la luz
interior del conservador con la puerta
cerrada.
3
4. Puerta de vidrio templado: Polarización
para proteger contra radiación UV pero
A
permite ver fácilmente el interior.
B
C
D
Ancho
Alto
Profundidad
Instrucciones de Operación
2
1
8
5. Estantes con bordes de acero
inoxidable
6. Repisa para vino : Permite guardar hasta
siete (7) botellas de vino.
7. Patas Niveladoras
8. Juntas Magnéticas de la Puerta: Las
juntas ajustadas mantienen todo el poder
de enfriamiento y los niveles de humedad.
Especificaciones
19,44" / 493mm Temperatura
33,06" / 840 mm Peso Neto
24,13" / 613mm
29
3
4
5
6
7
39,2~64,4°F / 4~18°C
97 libras / 44 kg