Gas Cylinder; Technical Data - Napoleon GPFR40 Manual

Correct Disposal Of This Product
This marking indicates that this product should not be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material resources. To return your used device,
please use the return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmental safe recycling.
Gas Cylinder
Use only gas cylinders, which meet national and regional codes. The minimum cylinder size for butane
units is 13kg, and for propane units is 6kg. Ensure that the cylinder can provide enough fuel to operate the
appliance. If in doubt, check with your local gas supplier.
• Use caution when handling the cylinder valve.
• Never connect a cylinder, which does not meet local codes.
• All cylinders 7kg or larger must be placed outside the enclosure on level ground. Cylinders smaller
than 7kg (maximum size 465mm high by 306mm wide) may be placed inside the enclosure. Only
cylinders connected to the appliance may be stored in the enclosure, or close to the appliance. Spare
cylinders must not be stored in the enclosure, or in close proximity of an operating unit. Cylinders
must not be exposed to extreme heat or direct sunlight.
WARNING!
Ensure that the hose is routed to maintain proper clearance to the underside of the
unit. Hoses that contact high temperature surfaces may melt and leak, causing a fire.
Cylinder Connection: Remove the cap or plug from the cylinder fuel valve. Tighten regulator to cylinder
valve. Leak test all joints prior to using. A leak test must be performed annually, and each time a cylinder is
hooked up, or if a part of the gas system is replaced.
Gas Hose
• If the hose and regulator are not included by the manufacturer, then only hoses and regulators which
meet national and regional codes are to be used.
• Ensure that the gas hose does not come into contact with any hot surfaces on the appliance -
particularly the underside of the burner.
• Check hose regularly. In the case of rips, melting or wear, replace hose before using the appliance.
• The recommended hose length is 0.9m. The hose must not be longer than 1.5m.
• Ensure that the hose is twist and kink free when installed.
• Replace the hose before expiry date printed on the hose.
Technical Data
The following table lists input values for the appliance.
Orifice Size
I II III
#51 #53 #36
Certified Gases / Pressures - Check rating plate to ensure that it corresponds with following list.
Gas Category I
3B/P(30)
Orifice Sizes(see I
above)
Gases / Pressures Butane and
Propane at
30mbar
Countries BE, BG, CY, DK,
EE, FI, FR, GB,
HR, HU, IS, IT,
LT, LU, MT, NL,
NO, RO, SE, SI,
SK, TR
Do not tamper with or modify regulator. Use only regulators which supply the pressure listed in the table
above. For replacement, use only the regulator specified by the manufacturer.
(Gross) Heat Input (Total)
11.5 kW
I I
3+(28-30/37) 3B/P(50)
I II
Butane 28- Butane and
30mbar Pro- Propane at
pane 37mbar 50mbar
BE, CH, CY, CZ, AT, CH, DE, SK AT, BG, CH, CZ,
ES, FR, GB, GR,
IE, IT, LT, LU, LV,
PT, SK, SI
Gas Usage (Total)
I/II III
837 g/hr 1092 L/hr
I I I
2H 2E 2E+
III III III
G20 at 20mbar G20 at G20/G25
20/25 at 20/25
mbar mbar
DE, LU, BE,FR
DK, EE, ES, FI, GB, PL
GR, HR, HU, IE, IS,
IT, LV, LT, NO, PT,
RO, SE, SI, SK, TR
www.napoleongrills.com
5
EN