Download Print this page

Cisco SCH-CONTROL-200 Reference Manual

Smart+connected controller 200.
Hide thumbs

Advertisement

Cisco Smart+Connected Controller 200
Reference Guide
This document provides information about the available ports, technical specifications and features of
Overview, page 2
Warranty, page 12
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Advertisement

   Related Manuals for Cisco SCH-CONTROL-200

   Summary of Contents for Cisco SCH-CONTROL-200

  • Page 1: Table Of Contents

    Resetting the Device Network Settings, page 9 • Regulatory/Safety Information, page 10 • • Specifications, page 10 • Related Documentation, page 11 • Warranty, page 12 Service and Support, page 12 • Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA...

  • Page 2: The Cisco Smart+connected Controller 200 (sch-control-200)

    Residential Solution, allowing residents to manage lighting, security, temperature, and multimedia, while also providing a portal into the community from the residence. The Cisco Controller 200 integrates a broad range of devices using a variety of protocols (Internet Protocol [IP], ZigBee HA, infrared [IR], serial, and more).

  • Page 3: Mounting The Cisco Controller 200 On A Wall

    11 for more information. Mounting the Cisco Controller 200 on a Wall The Cisco Controller 200 can be mounted on a wall or placed on a horizontal surface (such as a shelf). Procedure To mount the device on a wall:...

  • Page 4

    Mounting the Cisco Controller 200 on a Wall Figure 2 Mounting the Cisco Controller 200 Slots to horizontally mount the Controller 200 Holes for attaching the plate to the Controller 200 Slots to vertically mount the Controller 200 Use the four (4) screws (provided) to attach the mounting plate to the bottom of the Controller 200.

  • Page 5: Front View (leds And Other Features)

    Power LED—Blue LED light indicates AC power is present. This LED turns on immediately after the power is applied to the device. Factory Restore Button (bottom of device)—Restores the Controller 200 to the factory default settings. See the “Restoring the Device to the Factory Settings” section on page Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01...

  • Page 6: Rear View (input And Output Ports)

    Use the Composer Pro software to step through the connection process before or after the physical Note connections are completed. See the Cisco Smart+Connected Residential Installation and Configuration Guide for more information. Connect all applicable devices to the Controller 200 using the connection options described in the following table.

  • Page 7

    NTSC signal on the component video output connections occurs. However, the video image will not appear correctly in this mode. The Cisco Controller 200 can be configured to output over component using NTSC (standard definition) or 720p (high definition).

  • Page 8: Connecting The Ir Ports/serial Ports (optional)

    IR Blaster Procedure In addition to IR emitters, the Cisco Controller 200 is also equipped with an IR blaster, which is located just left of the front LEDs. To use the blaster instead of an IR emitter, do the following:...

  • Page 9: Setting Up External Storage Device (optional)

    If during the boot sequence, the Status LED stays Orange, press and hold the Identification button until the LED blinks blue, and then release it. If the Cisco Controller is connected to a TV, a message will appear indicating when to let go of the button.

  • Page 10: Regulatory/safety Information

    Shelf (with A/V gear) Wall/TV mount Yes (included) Dimensions (H×W×D) 1.44 in. x 8.55 in. x 5 in. (36.5 mm x 217 mm x 127 mm) Power Power supply External Power supply Input: 100–240V, 50–60 Hz Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01...

  • Page 11: Related Documentation

    Related Documentation Related Documentation For more information about the Cisco Smart+Connected Residential products, see the following documents and websites: Subject / Document Title Location General Product Information and Home Page www.cisco.com/go/smartconnectedresidential Cisco 1-Year Limited Hardware Warranty Terms www.cisco.com/go/smartconnectedresidential warranty Regulatory Compliance and Safety Information for Cisco Smart+Connected www.cisco.com/go/smartconnectedresidential/...

  • Page 12: Warranty

    Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

Comments to this Manuals

Symbols: 0
Latest comments: