Download Print this page

Sanyo PLC-8800E Service Manual page 65

Advertisement

[^ Take Notice Of "SCHEMATIC DIAGRAMS" ^
PRODUCT SAFETY NOTtCE
THE COMPONENTS DEStGNATED BY A MARK ( A ) !M TH)S SCHEMATtC DIAGRAM DESIGNATE
COMPONENTS WHOSE VALUES ARE OF SPEOAL S)GN)F)CANCE TO PRODUCT SAFETY. SHOULD
ANY COMPONENT DESIGNATED BY A MARK NEED TO BE REPLACED, USE ONLY THE PART
DES)GNATED tN THE PARTS UST. DO NOT DEV)ATE FROM THE REStSTANCE, WATTAGE AND
VOLTAGE RATINGS SHOWN.
SERVICE NOTES;
1. When reptacing parts on circuit boards, ctamp the !ead wiree to terminats before soidering.
2. When replacing high wattage resistors on circuit board, keep the resistor body 10 mm (3/8") from circuit
board.
3. Keep wires away from high voftage and high temperature components.
NOTES ON SCHEMATA DtAGRAM
Specification of capacitor and resistors wifi be shown
with coded symbots. reading code symbols following
the chart and notes. Some capacitor and resistors wiii
be shown directly with vaiues and no other infor-
mation. Detaited information on each capacitor and
resistor wiff be shown in the fist.
DO NOT REPLACE OR ORDER REStSTOR AND
CAPACITOR PARTS FOLLOWING THE SPECiFi-
CATfONS SHOWN fN THE SCHEMATIC DtA-
GRAMS.
ALWAYS CHECK FOR THE CORRECT SPECiFf-
CATtONS fN THE PARTS UST. ESPEOALLY FOR
CRmCAL COMPONENT MARKED A . SPECIAL
ATTENTiON MUST BE GIVEN TO CRITICAL COM-
PONENTS.
Read resistor codes as foiiows:
1. Aii resistance vaiues are indicated in
ohms: K=1,000. M=1.000,000.
2. Read wattage, materiaf and toierance
codes fotiowing the chart.
Read capacitor codes as foHows:
1. For capacitors identified with-f p, vaiues iess than
1 are expressed in ^ F , va)ues more than
1 are in pF.
2. For capacitors (ofectroiyttc) identrfiod with -H-
vaiues are expressed in ^ F.
Voltage and waveforms were taf<en using a video
coior bar signai (1V p-p). Line vottage is 240V.
VoMages were taken with a high-impedance
voitmeter.
Capacitor and Resistors Code Chart
CAPAC!TOR fEttmptt)
900 C )f )MO B
HES'STOR ^'*mp)t)
Cha.ractenstic
Vatue code
Toferance code-
Materiaf code -
Vo)tage number
,—D
—T
—J
— X
—M
— W
—P
—Z
^—C
T——C
— E
—F
— N
—T
—K
—H
—P
L-M
10%
0%
± 0-5pF
+ 50% -
-+5%
. ± 10%
I 20%
±30%
+ 100%
^ 80% - 20%
± 0-25pF
. Ceramic
Efeetro)ytic
Po^eater
- Potypropybne
. Tantatum
. Ceramic
.MT-Composite
.NP.EiectroHic
. MT- poiyropytene
Toterance code -
Metonateode -
. Wattage number
^D
-F
-G
-J
-K
-M
-F
-N
-S
-Y
-C
-D
-W
±0-5%
±1%
±2%
±5%
±10%
±20%
Carbon fi)m
Metaiized carbon
Oxide mgtatixed
W!rewound
So!id
Carbon f![m
Wire Wound
65

Advertisement

loading