Advertisement
Quick Links
This
installatio
n and ope
THIS A
APPLIANCE MU
UST BE INSTALL
CO Alarms
s:‐
Building re
egulations req
uire that when
installed in
n a dwelling a
carbon monox
guidance o
on the installat
tion of the car
manufactu
urer's instructi
ions. Provision
appliance
correctly or en
nsuring regula
A "Declara
tion of Comple
etion" Certifica
Failure to c
comply with th
hese requireme
Tested to EN
N 13229
eVo 4&7 I
Inset MS07‐1
1
Instal
lation an
d Operat
eration guid
de covers
LED AND COMM
MISSIONED BY
never a new o
r replacement
xide alarm mu
ust be fitted in
rbon monoxide
e alarm is avai
n of an alarm m
must not be co
r servicing and
d maintenance
ate must be ob
btained for the
ents will void t
the warranty.
t
tested to PD6
tion Man
ual
the eVolu
tion 4 & 7
Y A FULLY QUA
LIFIED, REGIST
t fixed solid fue
el or wood/bio
the same room
m as the appli
ilable in BS EN
50292:2002 a
onsidered a sub
bstitute for eit
e of the applia
nce and chimn
e installation an
nd retained by
6434
1
Inset Stov
ve
TERED ENGINEE
ER.
omass applian
nce is
ance. Further
and from the a
larm
ther installing
the
ney system.
the end user.
DINplus
11/0
07/11
Advertisement
Related Manuals for Broseley eVolution 4
Summary of Contents for Broseley eVolution 4
- Page 1 1 Instal lation an d Operat tion Man ual This installatio n and ope eration guid de covers the eVolu tion 4 & 7 Inset Stov ve THIS A APPLIANCE MU UST BE INSTALL LED AND COMM MISSIONED BY Y A FULLY QUA LIFIED, REGIST TERED ENGINEE ER. CO Alarms s:‐ Building re egulations req uire that when never a new o...
- Page 2 2 EVOLUTION INSET STOVE INSTALLATION & OPERATION MANUAL Thank You May we take this opportunity to thank you for choosing an eVolution wood burning inset stove. Please take time to read this manual and follow the guidelines on how to operate your new stove, as we feel sure it will enable you to use it to its best advantage for many years. The installer will need to read this documentation also, before any work is started. This appliance is designed to burn wood logs only. The air controls on the appliance allow the chosen fuel to burn efficiently. On an open fire, the conditions required to allow wood or other fuels to burn affect the efficiency, sending more than 60% of the heat produced straight up into the chimney. The efficiency figures for our stoves are much higher, as there is far greater control over the combustion air entering and leaving the appliance. Choosing the Correct Appliance It is essential that you size your stove correctly for your heating requirements. It is essential that you employ the services of an experienced heating engineer to calculate the heat demand you have, and that s/he, in turn, calculate the size of stove that would be most suitable for you application. Installing the Appliance IT IS A LEGAL REQUIREMENT UNDER ENGLAND AND WALES BUILDING REGULATIONS THAT THE INSTALLATION OF THE STOVE IS EITHER CARRIED OUT UNDER LOCAL AUTHORITY BUILDING CONTROL APPROVAL OR IS INSTALLED BY A COMPETENT PERSON REGISTERED WITH A GOVERNMENT‐APPROVED COMPETENT PERSONS SCHEME. HETAS LTD OPERATES SUCH A SCHEME AND A LISTING OF REGISTERED COMPETENT PERSONS CAN BE FOUND ON THEIR WEBSITE AT WWW.HETAS.CO.UK. IT IS A FURTHER CONDITION OF YOUR WARRANTY THAT YOUR BROSELEY STOVE MUST BE INSTALLED BY A CERTIFIED HEATING ENGINEER. FAILURE TO COMPLY WITH THIS REQUIREMENT WILL VOID YOUR WARRANTY. We recommend that you seek the services of an installer who is conversant with stove installations and Building Regulations. It is most likely that the shop where you purchased the stove will be able to help in this respect. It is our general policy to supply specialist Fireplace shops. These shops can offer an after sales service and will be able to offer advice when necessary. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 3 3 Useful organizations Solid Fuel Association 0845 601 4406 www.solidfuel.co.uk The National Association of Chimney Sweeps 01785 811732 www.chimneyworks.co.uk HETAS Ltd. 0845 634 5626 www.hetas.co.uk Health and safety precautions Special care must be taken when installing the stove such that the requirements of the Health and Safety at Work Act 1974 are met. Handling Adequate facilities must be available for loading, unloading and site handling. Fire Cement Some types of fire cement are caustic and should not be allowed to come into contact with the skin. In case of contact, wash immediately with plenty of water. Asbestos This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the course of installation then please seek specialist guidance and use appropriate protective equipment. ...
- Page 4 4 Glass Cleaning and Care The stove glass is designed to withstand heat up to 750°C. Care must be taken to ensure fuel is not stacked so it is possible to fall onto the glass. The glass may acquire a small amount of residue when the stove is operated at low outputs. Cleaning of the glass must be done when the stove is not in operation. Once the stove is cool and not being used a glass cleaner with cloth or news paper with some ash may be used to clean. Another option is a fine wire wool if the residue is to thick for the methods above. The Clean Air Act 1993 and Smoke Control Areas Under the Clean Air Act local authorities may declare the whole or part of the district of the authority to be a smoke control area. It is an offence to emit smoke from a chimney of a building, from a furnace or from any fixed boiler if located in a designated smoke control area. It is also an offence to acquire an "unauthorised fuel" for use within a smoke control area unless it is used in an "exempt" appliance ("exempted" from the controls which generally apply in the smoke control area). The Secretary of State for Environment, Food and Rural Affairs has powers under the Act to authorise smokeless fuels or exempt appliances for use in smoke control areas in England. In Scotland and Wales this power rests with Ministers in the devolved administrations for those countries. Separate legislation, the Clean Air (Northern Ireland) Order 1981, applies in Northern Ireland. Therefore it is a requirement that fuels burnt or obtained for use in smoke control areas have been "authorised" in Regulations and that appliances used to burn solid fuel in those areas (other than "authorised" fuels) have been exempted by an Order made and signed by the Secretary of State or Minister in the devolved administrations. Further information on the requirements of the Clean Air Act can be found here: http://smokecontrol.defra.gov.uk/ Your local authority is responsible for implementing the Clean Air Act 1993 including designation and supervision of smoke control areas and you can contact them for details of Clean Air Act requirements" ...
- Page 5 5 USER GUIDE – READ THESE INSTRUCTIONS CAREFULLY BEFORE USING YOUR STOVE Before lighting the stove check with the installer that the work and checks described in the Installation Instructions have been carried out correctly and that the chimney has been swept, is sound and free from any obstructions. CO Alarm Your installer should have fitted a CO alarm in the same room as the appliance. If the alarm sounds unexpectedly, follow the instructions given under the Warning Note on Page 15. Fuels The HETAS Ltd. appliance approval only covers the use of the following fuels in this appliance: • Wood logs not exceeding 20cms in length. Approval does not cover the use of other fuels either alone or mixed with the suitable fuels listed above, nor does it cover instructions for the use of other fuels. Under NO circumstances burn ‘petroleum coke’ as it will burn out the internal grate and baffle plates in a very short period of time and may damage the stove beyond repair and you run the risk of your warranty being voided. Burning Wood Ensure that you use well‐seasoned wood, less than 20% moisture; this will give a good heat yield and help to keep the glass clean. A growing tree contains 50‐65% water. Burning unseasoned wood turns most of the energy released into water vapor which goes into the flue and substantially reduces the heat that is given off to the room. The moisture will combine with other combustion products forming a sticky surface and the risk of obstruction, or worse still a chimney fire, is greater. Wood logs are best stored in a stack, sheltered from the weather, in a well ventilated area and raised off the ground. This allows the air to circulate and prevents mildew. eVo 4&7 Inset MS07‐11 ...
- Page 6 6 BURNING WOOD IN A SMOKE CONTROL AREA. The eVolution Inset Wood burning stoves have been testedby GASTEC under the PD6434 standard and have passed the emission requirements for exemption under the Clean Air Act. Subsequently it has been exempt for use in smoke control areas when burning wood only Below are detailed operation techniques that must be adhered to at all times when burning in a smoke control zone. eVo 7 Inset Refueling The refueling procedure adopted for the PD6434 tests allows the newly charged fuel to burn with the door set on the latch but not closed, the primary control set fully open for 1‐2 minutes and the secondary air set in the required positions necessary for the various outputs. After 1‐2 minutes, with the logs burning well, the door and primary air supply needs to be closed but the secondary air control position can remained unaltered. The tertiary air supply is maintained with its permanent opening throughout. Ignition The procedure adopted for ignition is to build a bed of embers in stages with the objective of warming the stove as quickly as possible. Firstly, a double‐handful of kindling (equivalent to the weight of about 1 kg) should be lit with chemical firelighters. The primary air and secondary air controls must be fully open at this stage. The fire‐door needs to be pushed against the latch but not closed, leaving a gap of a few millimeters. After about 8 minutes, with the fire bed dying back, 3 half‐sized logs (total weight about 1.2 kg) should be added with the air controls unaltered. After approximately a further 2 minutes, when these logs are well alight the door and primary air supply can be closed. Then allow the fire to burn down to embers with the secondary air supply maintained at maximum, at which point the ignition sequence is deemed to have ended. eVo 4 Inset Refueling There is a requirement for the door to be left ajar for 3 minutes immediately after refuelling. This is to ensure that flames are well‐established on the newly charged logs and that they become fully blackened. Additionally, for medium and low output burning, the Secondary air control must be maintained at 100% open for the first 3 minutes after refuelling at which time it is possible to adjust to the required settings as identified above. The primary air intake is not required at this stage. eVo 4&7 Inset MS07‐11 ...
-
Page 7: Further Requirements
7 Ignition The procedure adopted for ignition is to build a bed in stages and to warm the body of the appliance and the chimney as quickly as practicable. Firstly kindling, weighing approximately 1 kg will need to be lit (using a chemical firelighter is recommended) with the air control fully open. The door must be pushed against the appliance but then left ajar. After about 10 minutes, when the fire from the kindling is beginning to die back, two small logs can be added. When these are alight and fully blackened, the door can be closed. This, typically, takes approximately a further five minutes. When the fire is again beginning to die back, a full load of two logs, weighing about 1.3 ‐1.4 kg, can be added: typically this takes 20 – 25 minutes from the start of the ignition sequence. The Secondary air control must be maintained in its fully open position for the remainder of the ignition sequence. Once the fuel has blackened the fire can then be allowed to burn down to a suitable condition at a preferable air slider position. For start of further re fuelling apply sequence in the previous 2 sentences. FURTHER REQUIREMENTS: 1. It is important to follow these instructions in order to achieve clean burning and to maximise the efficiency from the stove 2. Do not leave the fire unattended after refueling until flames are well‐established on the newly charged logs 3. Refuelling on to a low fire bed If there is insufficient burning material in the firebed to light a new fuel charge, excessive smoke emission can occur. Refuelling must be carried out onto a sufficient quantity of glowing embers and ash that the new fuel charge will ignite in a reasonable period. If there are too few embers in the fire bed, add suitable kindling to prevent excessive smoke 4. Fuel overloading The maximum amount of fuel specified in this manual should not be exceeded, overloading can cause excess smoke. 5. Operation with door left open Operation with the door open can cause excess smoke. The appliance must not be operated with the appliance door left open except as directed in the instructions. eVo 4&7 Inset MS07‐11 11/07/11 ... - Page 8 8 6. Dampe ers left open Operation n with the air controls or d dampers open n can cause e xcess smoke. . The applian nce must not be operated with air cont trols or damp ers door left open except as directed in n the instruct tions. Control La ayout There are e two air cont rols on the eV Volution Inse t stove. Cont rol ‘A’ contro ols the main c ombustion ai ir and airwash sy ystem. Contr ol ‘B’ controls s tertiary air w which can be used for initi ial start up on n the applianc ce. ...
- Page 9 9 Control B Control B operates the Primary air which can be used for initial start up of the appliance. The control is operated by sliding the control left to right. To open the control fully, slide the control to the left and to shut the air control slide the control fully to the right. The tool and gloves supplied must be used at all times when operating the stoves controls and removing the grate and ash pan. It is recommended that the removal of the grate and ash pan is done prior to lighting the stove when no hot embers/ ashes are evident. Burning Wood Logs If you are only burning wood logs, you may allow a bed of ash to build up on top of the grate to a level of about 20mm, forming a flat surface on which the wood will burn. You should then use the thermostat control and the air wash control to maintain the burn rate. To fully open the combustion air, turn the knob clockwise, to fully open the air wash slide the slider to the left. The ‘fully open’ setting will produce the fastest burn, yielding most heat. You will not have to clean out your stove after every firing as wood will burn better with a slight build up of ash in the ash pan. It is not advisable to burn painted or recovered wood (such as railway sleepers) as this contains harmful toxins or flammables which may cause the wood to ‘spit’. Overnight burning is difficult to achieve with logs. ‘Curing’ the Stove Before lighting the stove, check with the installer that the installation work and commissioning checks described in the installation instructions have been carried out correctly and that the chimney has been swept clean, is sound and free from any obstructions. The curing process may have been undertaken by your installer as part of the stove’s commissioning and handover and the installer should have shown you how to operate the stove correctly. Your stove is made of a number of cast iron components and we recommended that the first burn should be a small fire lasting about 30 minutes. This enables the stresses and strains at the joints to be taken up and settle gradually. The second burn can be a larger fire lasting for about an hour. During the curing process, the stove will give off a pungent smell and some fumes. This is the paint ‘curing’ and is quite normal. Provide plenty of ventilation whilst this is happening since the fumes can be quite strong and may set off smoke alarms in the room. The paint may become slightly lighter in colour when the stove is cured, particularly in the hottest spots. Fire Grate polish can be used to keep the stove in good condition, or stove spray paint can be used to re‐touch the stove. The correct stove spray can be obtained from your stove stockist. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 10 10 Starting and Maintaining the Fire ` For safety reasons, do not use gasoline, lighter fluid, kerosene or other flammable liquids to start or rekindle the fire. Build a fire directly on the grate with crumpled newspaper, kindling wood and/or commercially available “firelighters”. Do not allow single pieces of paper to float up the chimney, especially if alight. This is a common cause of chimney fires and can cause structural damage to the property. Ensure that the air control and the thermostat control are fully open to begin with and ensure that the thermostat control is on its highest setting. When the kindling is burning well, add larger pieces of wood. The stove will work more efficiently with the main door closed as you will be able to control the combustion air and the rate of fuel burning. It is not recommended to operate the stove with the fuel loading door open other than to load fuel, as this can lead to over‐firing and damage to your stove, which may void your warranty. When the appliance is a light, the loading door handle and the ash pan handle will become hot. Please use the glove provided to avoid touching hot parts. Chimney Fires If the chimney is thoroughly and regularly swept, chimney fires should not occur. However, if a chimney fire does occur turn the air control setting to the minimum, and tightly close the doors of the stove. This should cause the chimney fire to go out in which case the control should be kept at the minimum setting until the fire in the stove has gone out. The chimney and flue ways should then be cleaned. If the chimney fire does not go out when the above action is taken then the fire brigade should be called immediately. After a chimney fire, the chimney should be carefully examined for any damage. Expert advice should be sought if necessary Chimney Cleaning and Stove Maintenance. The chimney should be swept at least twice a year. It is important that the flue connection and chimney are swept prior to lighting up after a prolonged shutdown period. If the stove was fitted in place of an open fire then the chimney will require sweeping after a month of continuous operation. This is a precaution to ensure that any “softer” deposits left from the open fire usage have not been loosened by the higher flue temperatures generated by the closed stove. Page 20‐27 describes how to remove the baffle plate for access for sweeping through the appliance. It is very important to ensure the baffle plate is always clean. The baffle plate should be checked and cleaned on at least a monthly basis. After sweeping the chimney the stove flue outlet and the flue pipe connecting the stove to the chimney must be cleaned with a flue brush. ...
- Page 11 11 Trouble‐Shooting 1. Smoke comes out of the stove when the loading door is opened. • The chimney cavity into which the 150mm flue pipe has been installed may be less than the minimum requirement. • Deposits (soot) may have built up in the chimney and be restricting the flow of waste products. This flow rate is known as the ‘draw’. 2. The Stove does not produce the expected heat into the room. • Has the flue pipe been sealed to the chimney to prevent heat being drawn up the chimney to waste? • Green or wet wood is being burnt. • The chimney has excessive draw (this is unusual). Seek installer advice with regard to installing a Flue Draught Stabiliser. 3. The Stove burns too fast. • Use whole logs rather than split ones. • The wood being used may be generally too small. • The “air‐tight” seal between the fibre rope on the doors and the casting may have been lost, adjust door handle lock nuts to reinstate this seal. • The chimney has excessive draw (seek installers advice on this point). • The fibre rope seal between the door and the glass may be leaking. Tighten or replace. ...
-
Page 12: Important Warning
12 Installation Guide – For Use by the Qualified Installer Read These Instructions Carefully Before Installation IMPORTANT WARNING These instructions cover the basic principles to ensure the satisfactory installation of the stove, although detail may need slight modification to suit particular local site conditions. In all cases, the installation must comply with all current Building Regulations, Local Authority Byelaws and other specifications or regulations as they affect the installation of the stove. It should be noted that the Building Regulations requirements may be met by adopting the relevant recommendations given in British Standards BS 8303, BS 6461 and BS 5449 as an alternative means to achieve an equivalent level of performance to that obtained following the guidance given in Approved Document J. It is essential that you seek the services of a registered engineer who is conversant with stove installations and Building Regulations. It is most likely that the shop where you purchased the stove will be able to help in this respect. It is our general policy to supply specialist Fireplace shops. These shops can offer an after sales service and will be able to offer advice when necessary. CO Alarms:‐ Building regulations require that whenever a new or replacement fixed solid fuel or wood/biomass appliance is installed in a dwelling a carbon monoxide alarm must be fitted in the same room as the appliance. Further guidance on the installation of the carbon monoxide alarm is available in BS EN 50292:2002 and from the alarm manufacturer’s instructions. Provision of an alarm must not be considered a substitute for either installing the appliance correctly or ensuring regular servicing and maintenance of the appliance and chimney system. Stove Performance In the UK, the stove has been approved by HETAS Ltd as an intermittent operating appliance for burning wood logs only. It should be noted that it is an offence to burn wood logs in any stove if it is installed within a Smoke Control Area in the UK and the appliance has not been approved for use in a Smoke Control Area. The nominal figures tested under EN13229 for the 2 stoves are as follows: eVolution 4 Inset eVolution 7 Inset Heat Output 4.2kW ... - Page 13 13 Other fulfilled Requirements eVolution 4 Inset ‐ BStv of the City of Munich, the City of Ragensburg and the City of Stuttgart ‐ LRV of Switzerland ‐ Level 1 of the BlmSchV Sizing the appliance It is essential that this appliance is correctly sized for the area it is required to heat. This should be done by carrying out a heat loss calculation for the property and taking into consideration the client’s requirements. Hearth Requirements and Clearances Your stove must be installed on a solid, level non‐combustible hearth and with a gap of at least 600mm from any combustible material such as beams or skirting. The hearth does not need to be constructional but must be at least 12mm thick. The hearth protrusion in front of the stove to carpets or wooden floors must be at least 300mm. As it is possible for fuel to fall out on opening the door, a fender must be fitted if the hearth is flush with the carpet. These are just a few hearth specifications. Please refer to Building Regulations Approved Document J (Hearths) for more specific details. Clearances to combustibles are detailed in the diagram below. 300mm above and 100mm to the side must be obtained to any flammable material such as wooden surrounds for example. These figures are based on the fact that the stoves forward projection is no more than 150mm. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 14 14 Chimney and Flue Requirements The liner diameter must not be less than 6 inch (150mm) and no more than 9 by 9 inch (225mm by 225mm) square. It is most important that there is no obstruction in the flue. Sweep clean immediately before installation of the stove. If the chimney has previously been used for an open fire it is recommended that it be swept for a second time after the stove has been used for a month. As a closed appliance operates at a higher flue temperature, it is possible for deposits which previously adhered to now be dislodged, with the consequent risk of soot falls and flue blockage. A flue draught of minimum 12Pa (0.05ins wg) to a maximum 16 Pa (0.065ins wg) is required for satisfactory appliance performance. A properly built masonry or factory constructed chimney, preferably with a height of 5 metres or more, should ensure a consistent draught (draw) under a variety of weather conditions. The flue draught should be checked ‘under‐fire’ at high output and if it exceeds the recommended maximum, a draught stabiliser should be fitted to prevent over firing (see 5 below). This appliance must not be connected to a flue serving another heating appliance. The outlet from the chimney should be above the roof of the building in accordance with the provisions of Building Regulations Approved Document J. If installation is into an existing chimney then the chimney must be sound and have no cracks or other faults which might allow fumes into the house. If there is any uncertainty, seek expert advice as remedial action should be taken. If it is found necessary to line the chimney then a flue liner suitable for manufactured or naturally occurring smokeless fuels and wood logs must be installed in accordance with Building Regulations Approved Document J. If there is no existing chimney then either a prefabricated block chimney in accordance with Building Regulations Approved Document J or a twin walled insulated stainless steel flue to BS 4543 can be used. These chimneys must be fitted in accordance with the manufacturer’s instructions and Building Regulations. The liner diameter must not be less than 6”. If the draw on the chimney is excessive, a flue draught stabiliser will help to slow this down. An excessive draw may cause over firing and thus cause the internal components of the stove to wear out quicker. Any bend in the chimney or connecting fluepipe should not exceed 45°. 90° bends should not be used. Adequate provision e.g. easily accessible soot door or doors must be provided for sweeping the chimney and connecting fluepipe. With reference to the above All relevant flue or chimney installations must adhere to BS EN 15287‐ 1:2007 Design, installation and commissioning of chimneys. eVo 4&7 Inset MS07‐11 11/07/11 ...
-
Page 15: Warning Note
15 WARNING NOTE Properly installed, operated and maintained this stove will not emit fumes into the dwelling. Occasional fumes from de‐ashing and re‐fuelling may occur. However, persistent fume emission is potentially dangerous and must not be tolerated. If fume emission does persist, then the following immediate action should be taken:‐ (a) Open doors and windows to ventilate the room and then leave the premises. (b) Let the fire go out. (c) Check for flue or chimney blockage and clean if required (d) Do not attempt to relight the fire until the cause of the fume emission has been identified and corrected. If necessary seek expert advice. The most common cause of fume emission is flue way or chimney blockage. For your own safety these must be kept clean at all times. eVo 4&7 Inset MS07‐11 ... - Page 16 16 SUMMARY OF FLUE PRO O BLEMS eVo 4&7 I Inset MS07‐11 11/0 07/11 ...
- Page 17 17 Air Control Requirements when the appliances is used in Smoke Control Areas when burning wood eVolution 7 The eVo 7 stove has been tested under PD6434 and found to be suitable for burning wood logs in a smokeless zone. It is mandatory that when installing the stove in a smokeless zone that the airwash deflector plate be altered to ensure some permanent air is available. Following the image below the installer will need to change the 4 screws from their original position to the 4 holes drilled immediately to the right. This will ensure the slider cannot close completely leaving some permanent air. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 18 18 eVo 4 The eVo 7 stove has been tested under PD6434 and found to be suitable for burning wood logs in a smokeless zone. It is mandatory that when installing the stove in a smokeless zone that the airwash deflector plate be altered to ensure some permanent air is available. Following the image below the installer will need to change the 4 screws from their original position to the 4 holes drilled immediately to the right. This will ensure the slider cannot close completely leaving some permanent air eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 19 19 eVo 4 Vermiculite and Baffle layout/ Removal To easily connect the flue it is possible to remove all vermiculite and access the adaptor/spigot from inside the stove. To refit the vermiculite, perform the following sequence in reverse. Be careful when removing vermiculite as it is a fragile material. At no time hit the panels directly. STEP 1. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 20 20 STEP 2. STEP 3. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 21 21 STEP 4. STEP 5. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 22 22 eVo 7 Vermiculite and Baffle Layout/Removal To easily connect the flue it is possible to remove all vermiculite and access the adaptor/spigot from inside the stove. To refit the vermiculite, perform the following sequence in reverse. To start removing lift the top vermiculite baffle up and remove the rear firebrick by pulling from the top. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 23 23 STEP 1. STEP 2. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 24 24 STEP 3. STEP 4. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 25 25 STEP 5. STEP 6. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 26 26 STEP 7. STEP 8. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 27 27 Connection to flue pipe or liners (Both eVo4 and eVo7 Models) The stove can be connected directly into a standard fireplace opening conforming to BS1251 & BS8303. Connect and seal the 150mm flue pipe to the flue adaptor/spigot ‘A’ before situating the stove in the fireplace. This can be done by screwing the flue pipe using the 2 holes located in the adaptor/spigot. Extra assurance may be required to maintain an air tight seal between the flue pipe and the adaptor/spigot. This can be obtained by using rope and or fire cement. Then insert the stove into the fireplace and connect the flue adaptor/spigot to the appliance by means of the 2 bolts supplied inside the adaptor/spigot. The baffle will have to be removed to access the bolts to secure. IT IS RECOMMENDED THAT THIS STEP IS COMPLETED AFTER FIRST SITING THE STOVE AND ENSURING SECURE POINTS ARE MARKED AND OR DRILLED. See section fitting the stove on next 2 pages: eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 28 28 Where there is no direct and sealed connection to the chimney or chimney liner (where fitted) it is essential that the fire is sealed to the surround and the hearth using fire cement for a gas‐tight seal in accordance with BS 8303‐1. Fitting the stove eVo4 Inset Remove the flue pipe adaptor (if fitted) Insert the stove into the fireplace opening ensuring that the rope forms an airtight seal against the fireplace and hearth. Secure the stove with screws (not supplied as they need to be suitable to screw into the hearth material) into the hearth through the holes located inside the stove – holes ‘A’ and ‘B’. There are two holes located on the left and right hand side and one hole located in the middle of the stove. You should use all 3 holes to secure the appliance as holes not used will ensure excess air enters the combustion chamber which can cause issues with the air wash. If all holes are not used they must be blocked with silicone or firecement. Then use the chimney clamp (C) to hold the top of the appliance against the fireplace opening ensuring again that an airtight seal is formed. It may be a requirement to drill a clearance hole through the chimney breast on some installations for clamp C. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 29 29 Fitting the Stove eVo7 Inset The eVo 7 has 4 secure points on the base of the stove. The front 2 holes are identical to the eVo4 previous. The other 2 are located left and right central to the burn box. The vermiculite, grate, ash pan and grate support must be removed to access these holes. Once parts are removed mark the holes onto the hearth through the main door. Once marked it is the engineer’s discretion as to removing the stove and drilling the hearth or screwing into it directly. Either way it is recommended that at least 2 fixing points (opposite corners) are used. Please note that excess air can enter into the other 2 holes if they are not used. This will cause issues with the air wash so any hole not used must be blocked with heat resistant silicone or fire cement. Then as previous, use the chimney clamp (C) to hold the top of the appliance against the fireplace opening. It may be a requirement to drill a clearance hole through the chimney breast on some installations for clamp C. eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 30 On completion of the installation and commissioning ensure that the operating instructions for the stove are left with the customer. Ensure to advise the customer on the correct use of the appliance and warn them to use only the recommended fuel for the stove. Advise the user what to do should smoke or fumes be emitted from the stove. The customer should be warned to use a fireguard to BS 8423:2002in the presence of children, aged and/or infirm persons. Combustion Air Supply In order for the stove to perform efficiently and safely, there should be an adequate air supply into the room in which the stove is installed. This should be in accordance with Approved Document J. This is particularly necessary in modern houses, where draughts have been almost eliminated by double glazing etc. There must be no extractor fan fitted in the same room as the stove ‐ as this can cause the stove to emit fumes into the room. Spare Parts Details of spare parts are available from your local stockist from which you purchased this appliance or by contacting Broseley Fires. Contact Details: Broseley Fires Knights Way Battlefield Enterprise Park Shrewsbury Shropshire SY1 3AB Tel: 01743 461444 Email: info@broseleyfires.com Web: www.broseleyfires.com eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 31 31 eVo 4 Inset Dimensions eVo 4&7 Inset MS07‐11 11/07/11 ...
- Page 32 32 eVo 7 Inset Dimensions ...
- Page 33 33 This appliance must be installed and commissioned by a fully qualified, registered engineer. A “Declaration of completion Certificate” must be obtained for the installation and retained by the end user. Failure to comply with these requirements may void your warranty. You, as the end user, have a contract by law with the supplier / dealer from whom you purchased the product. That dealer then has the same contract with the manufacturer or wholesaler and these have a contract with their suppliers. ALL CLAIMS MUST FOLLOW THIS PROCEDURE. Thank you for choosing a Product from Broseley Fires Ltd. This warranty gives you specific legal rights. The statutory rights of the consumer are not affected by the warranty, or the consumers’ rights against the dealer arising from their sales / purchase contract. The manufacturers’ warranty: Your Product will be free from defective parts, material, and workmanship at the time of its original purchase for a period of one (1) year. This Warranty will become active as of one month from the date of delivery. This warranty does not cover any failure of the unit due to normal wear and tear, misuse, abuse, accident, illegal modification, illegal installation or repair, damage resulting from improper use or failure to maintain the product. Variations in color and texture are a natural characteristic of cast iron products. Colour changes may result from exposure to light and other elements which are a part of the aging process. These material variations and changes are not covered by this warranty. If during the warranty period, this Product fails to operate under normal use and service, due to defects in material and / or workmanship, Broseley Fires will either repair or replace the product.The repaired or replaced product shall be warranted for the remaining period of the original warranty + the time taken to days from the date of repair, whichever is longer. Repair or replacement may involve the use of functionally equivalent reconditioned units. Replaced parts or components will become the property of Broseley Fires. Should you wish to claim under the warranty, please contact the supplier / dealer from whom you purchased the appliance. Do not claim directly to Broseley Fires, as they are unable to process any direct claim from an end user. Product design and any specifications are subject to change without notice. This is due to our continuous product development and improvement. The buyer will not be entitled to request free upgrades to the new design or compensation for previously purchased products or any products on order. This Warranty covers all Broseley Fires costs within the Warranty period. If the appliance remains uninstalled for a period greater than six months from date of delivery the Warranty will become active six months from ...