Advertisement

Quick Links

Ethernet Switch
ESML3-FL2-D4-S2
ESML3-FL2-D4-M2

User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ESML3-FL2-D4-S2 and is the answer not in the manual?

Questions and answers

Summary of Contents for KBC ESML3-FL2-D4-S2

  • Page 1: User Manual

    Ethernet Switch ESML3-FL2-D4-S2 ESML3-FL2-D4-M2 User Manual...
  • Page 2: Table Of Contents

    5 NETWORKING & CONFIGURATIONS ........ 14 6 DIMENSIONS (MM) ............. 15 7 WARRANTY ............. 16 ................16 ARRANTY NFORMATION A ITE .................... 17 LASS FCC ....................... 17 8 INSTRUCTION OF DISASSEMBLY ........17 Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 2 of 18 www.kbcnetworks.com...
  • Page 3: Overview

    1 Overview 1.1 Introduction This manual covers the ESML3-FL2-D4 series. The KBC ESML3-FL2-D4 products are high performance, managed, five port industrial Ethernet switches with an embedded four port serial data servers. They are designed for use in a wide range of operating temperatures in non-environmentally conditioned, industrial applications.
  • Page 4: Technical Specification

    0 - 40Km(1310nm SM) Transmission distance 0 - 5Km(1310 MM) Connector Transmission rate 125Mbps(100M) Console Physical interface Shielded RJ45 Interface standard In line with RS232 standard (3 lines) Interface rate 9600bps Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 4 of 18 www.kbcnetworks.com...
  • Page 5: Installation

    Please contact you dealer or distributor if a part is missing or damaged. Configurations Products are available in either DIN rail or wall-mount packages, with the following configurations: Product Type DIN Rail Wall-mount Multimode Singlemode ESML3-FL2-D4-S2 ESML3-FL2-D4-M2 Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 5 of 18 www.kbcnetworks.com...
  • Page 6: Physical Connections

    Ethernet Switch User Manual 2.3 Physical Connections RUN1 RUN2 ALARM LNK/ACT 10/100M LNK/ACT ESML3-FL2-D4 Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 6 of 18 www.kbcnetworks.com...
  • Page 7: Installation Method

    Insert the male power block (attached to the supplied in-line PSU) to the • female power socket on the device and tighten the terminal locking screws using the flathead screw driver provided. See Section 2.8 for LED status. Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 7 of 18 www.kbcnetworks.com...
  • Page 8: Ethernet Rj45 Connections

    The two uplink redundant fiber ports can be used to form a fiber optic redundant ring network. If a system failure occurs, the redundant recovery time of the ring network is less than 50ms. Figure 2.1 Switch Ports Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 8 of 18 www.kbcnetworks.com...
  • Page 9: Data Ports

    FLASH Switch functioning correctly (left LED) Switch is off No power is supplied to either POWER 1 or POWER 2 (right LED) Power being supplied to both power inputs Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 9 of 18 www.kbcnetworks.com...
  • Page 10: Power Input Terminals

    DC power supplies to provide redundancy. The red sleeved wire should be connected to the +ve power input and the blue sleeved wire should be connected to the –ve power input of the green male screw block terminal. Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 10 of 18 www.kbcnetworks.com...
  • Page 11: Alarm Relay Output

    1 & 2 Open Closed 2 & 3 Closed Open 2.11.2 Dual Power Supplies Connected: Contacts Power On Power Off 1 & 2 Closed Open 2 & 3 Open Closed Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 11 of 18 www.kbcnetworks.com...
  • Page 12: Rs232 Console Interface

    LINK/ACT LED will flash to show data transfer and the yellow 10M/100M will either be off to show 10Mbps (10BASE-T) operation or on to show 100Mbps (100BASE-TX) operation. Figure: 3.1 Testing TP Ports Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 12 of 18 www.kbcnetworks.com...
  • Page 13: Fiber Port Testing

    LINK/ACT indicators of the fiber ports flash, this then shows the fiber ports under test are functioning correctly. Figure 3.2 Fiber Port Testing 4 System Example Figure 4.1 ESML3-FL2-D4 Typical System Application Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 13 of 18 www.kbcnetworks.com...
  • Page 14: Networking & Configurations

    50ms. A typical redundant ring set up is shown in Figure 5.1 below. Figure 5.1 Typical Ring Topology Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 14 of 18 www.kbcnetworks.com...
  • Page 15: Dimensions (Mm)

    Ethernet Switch User Manual 6 Dimensions (mm) Wall-mount: Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 15 of 18 www.kbcnetworks.com...
  • Page 16: Warranty

    KBC, to be defective in material or workmanship, KBC will repair or replace such part or portion at KBC’s option. The warranty period on the repaired or replaced part or portion of this product shall be limited to the unexpired term of the original warranty.
  • Page 17: Classa Ite

    2. Remove cover plate. 3. Remove tightening screws for printed circuit board (PCB). 4. Take out all PCBs. Notice: When a product reaches the end of its life – return to KBC. Manual_hw-ESML3-FL2-D4-Rev1011 Copyright © KBC Networks Ltd. Page 17 of 18...
  • Page 18 KBC Networks, Ltd. 25691 Atlantic Ocean Drive Suite 3B Lake Forest, CA 92630 U.S.A Americas Phone: 1-949-297-4930 Fax: 1-949-297-4933 KBC Networks Ltd. EMEA KBC Networks Ltd. Barham Court Teston, Maidstone Kent, ME18 5BZ United Kingdom Phone: +44(0)1622 618787 Fax: +44(0)20 7100 8147 Email: info@kbcnetworks.com...

This manual is also suitable for:

Esml3-fl2-d4-m2

Table of Contents