Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KBC ESUL6-FL2-M2
Summary of Contents for KBC ESUL6-FL2-M2
-
Page 1: User Manual
Ethernet Switch ESUL6-FL2-M2 ESUL6-FL2-S2 Hardware User Manual... -
Page 2: Table Of Contents
TROUBLESHOOTING ............... 13 ..................13 TESTING ..............13 WISTED ESTING ................14 IBER ESTING SYSTEM EXAMPLE ..............14 NETWORKING & CONFIGURATIONS ..........15 DIMENSIONS (MM) ..............16 WARRANTY ................. 17 ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 2 of 20 www.kbcnetworks.com... - Page 3 DRAFT VERSION NOT FOR RELEASE Ethernet Switch User Manual ................17 ARRANTY NFORMATION A ITE ..................18 LASS FCC ....................18 INSTRUCTION OF DISASSEMBLY ..........19 ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 3 of 20 www.kbcnetworks.com...
-
Page 4: Overview
Ethernet Switch User Manual 1 Overview 1.1 Introduction This manual covers the ESUL6-FL2 series. The KBC ESUL6-FL2 products are high performance, unmanaged, eight port industrial Ethernet switches designed for use in a wide range of operating temperatures in non-environmentally conditioned, industrial applications. -
Page 5: Technical Specification
<6W Over-current protection Built in Environmental Operating temperature 40°C - 85°C Storage temperature 40°C - 85°C 0% - 95% Relative humidity Non-condensing Mean Time Between Failure >300,000 hours ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 5 of 20 www.kbcnetworks.com... -
Page 6: Installation
Please contact you dealer or distributor if a part is missing or damaged. 2.2 Configurations Products are available in either DIN rail or wall-mount packages, with the following configurations: Product Type DIN DIN Rail Wall-mount Multimode Singlemode ESUL6-FL2-M2 ESUL6-FL2-S2 ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 6 of 20 www.kbcnetworks.com... -
Page 7: Physical Connections
DRAFT VERSION NOT FOR RELEASE Ethernet Switch User Manual 2.2.1 Physical Connections ESUL6-FL2 ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 7 of 20 www.kbcnetworks.com... -
Page 8: Installation Method
The connected devices should support this feature too however, if the connected devices are not adaptive the port will send at the correct rate but with default mode of half duplex. ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 8 of 20 www.kbcnetworks.com... -
Page 9: Fiber Optic Connections
The two pairs of uplink redundant fiber ports can be used to form a fiber optic redundant ring network. If a system failure occurs the redundant recovery time of the ring network is less than 100ms. Figure 2.1 Front Panel ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 9 of 20 www.kbcnetworks.com... -
Page 10: Grounding / Earthing
The uplink redundant fiber ports are in redundant mode and the switch is set as a master. Uplink fiber ports are in straight-through mode. ON/OFF ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 10 of 20 www.kbcnetworks.com... -
Page 11: Led Status
Effective network connection has been established for the port LINK/ACT FLASH Data traffic is passing through the port (Green) No effective network connection has been established for the port ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 11 of 20 www.kbcnetworks.com... -
Page 12: Power Input Terminals
350Vdc and maximum current is 120mA (see the diagram below for an example of this kind of set up). Figure 2.3 Alarm Lamp and Relay Output ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 12 of 20 www.kbcnetworks.com... -
Page 13: Troubleshooting
ACT LED will flash to show data transfer and the yellow LINK LED will either be off to show 10Mbps (10BASE-T) operation or on to show 100Mbps (100BASE-TX) operation. Figure: 3.1 Testing TP ports ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 13 of 20 www.kbcnetworks.com... -
Page 14: Fiber Port Testing
ACT indicators of the fiber ports flash, this then shows the fiber ports under test are functioning correctly. Figure 3.2 Fiber port testing 4 System Example Figure 4.1 ESUL6-FL2 Typical System Application ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 14 of 20 www.kbcnetworks.com... -
Page 15: Networking & Configurations
100ms. A typical redundant ring set up is shown in Figure 5.1 below. Figure 5.1 Typical Ring Topology ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 15 of 20 www.kbcnetworks.com... -
Page 16: Dimensions (Mm)
DRAFT VERSION NOT FOR RELEASE Ethernet Switch User Manual 6 Dimensions (mm) Wall-mount plate: ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 16 of 20 www.kbcnetworks.com... -
Page 17: Warranty
KBC, to be defective in material or workmanship, KBC will repair or replace such part or portion at KBC’s option. The warranty period on the repaired or replaced part or portion of this product shall be limited to the unexpired term of the original warranty. -
Page 18: Classa Ite
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own expense. ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 18 of 20 www.kbcnetworks.com... -
Page 19: Instruction Of Disassembly
2. Remove cover plate. 3. Remove tightening screws for printed circuit board (PCB). 4. Take out all PCBs. Notice: When a product reaches the end of its life – return to KBC. ESUL6-FL2_inst_manual-Rev 1009 Copyright © KBC Networks Ltd. Page 19 of 20... - Page 20 KBC Networks, Ltd. 25691 Atlantic Ocean Drive Suite 3B Lake Forest, CA 92630 U.S.A Americas Phone: 1-949-297-4930 Fax: 1-949-297-4933 KBC Networks Ltd., EMEA KBC Networks Ltd. Barham Court Teston, Maidstone Kent, ME18 5BZ United Kingdom Phone: +44(0)1622 618787 Fax: +44(0)20 7100 8147 Email: info@kbcnetworks.com...