Mitsubishi PKFY-NBMU-E2 Operation Manual page 7

5. Operation
5.2. Mode select
Press the operation mode (
eration mode .
Cooling mode
Drying mode
Fan mode
Heating mode
Automatic (cooling/heating) mode
Automatic operation
According to a set temperature, cooling operation starts if the room
temperature is too hot and heating operation starts if the room tem-
perature is too cold.
During automatic operation, if the room temperature changes and
remains 1.5°C, 3°F or more above the set temperature for 3 minutes,
the air conditioner switches to cooling mode. In the same way, if the
room temperature remains 1.5°C, 3°F or more below the set tempera-
ture for 3 minutes, the air conditioner switches to heating mode.
Cooling mode
3 minutes (switches from
heating to cooling)
3 minutes (switches from cool-
ing to heating )
Because the room temperature is automatically adjusted in order to
a few degrees warmer and heating operation is performed a few de-
grees cooler than the set room temperature once the temperature is
reached (automatic energy-saving operation).
5.3. Temperature setting
To decrease the room temperature:
Press button to set the desired temperature.
The selected temperature is displayed at
To increase the room temperature:
Press button to set the desired temperature.
The selected temperature is displayed at
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30°C, 67 - 87 °F
Heating: 17 - 28°C, 63 - 83 °F
Automatic: 19 - 28°C, 67 - 83 °F
• The display blinks either 8°C - 39°C, 46°F - 102°F to inform you if the
room temperature is lower or higher than the displayed temperature.
Press the Fan Speed button
system is running.
• Each press changes the force. The currently selected speed is
shown at .
• The change sequence, and the available settings are as follows.
FAN SPEED
4-speed
Speed 1 Speed 2
+
Auto *
Speed 1 Speed 2
3-speed
+
Auto *
Speed 1
4-speed
model
* For MA remote controller only.
Automatic fan speed setting is necessary for wireless remote controller.
) button and select the op-
Set temperature +1.5°C, +3°F
Set temperature
Set temperature -1.5°C, -3°F
.
.
as many times as necessary while the
Display
Speed 3 Speed 4 Auto
Speed 3 Auto
Speed 2 Speed 3 Speed 4
Note:
The number of available fan speeds depends on the type of unit connected.
Note also that some units do not provide an "Auto" setting.
In the following cases, the actual fan speed generated by the unit will differ
from the speed shown the remote controller display.
1. While the display is showing "STAND BY" or "DEFROST".
2. When the temperature of the heat exchanger is low in the heating mode.
3. In HEAT mode, when room temperature is higher than the temperature
setting.
It is necessary to set for wireless remote controller only when
automatic fan speed is not set at default setting.
It is not necessary to set for wired remote controller with automatic
fan speed at default setting.
Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
blinks and Model No. is lighted
MODEL SELECT
Press the AUTO STOP button.
blinks and setting No. is lighted
(Setting No.01: without automatic fan speed )
Press the temp. buttons to set the setting No.02.
(Setting No.02:with automatic fan speed )
If you mistook the operation, press the ON/OFF
ate again from procedure .
Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
MODEL SELECT
ON/OFF
FAN
MODE VANE
CHECK LOUVER
TEST RUN
SET RESET
sary.
• Each press changes the direction. The current direction is shown at
• The change sequence, and the available settings, are as follows.
Swing Auto
5 steps
model*1
Swing
(Horiz.)
4 steps
model
* Note that during swing operation, the directional indication on the
screen does not change in sync with the directional vanes on the unit.
* Some models do not support directional settings.
*1. For MA remote controller only, other remote controllers display the
same as 4 steps model.
*2. PKFY-P·NBMU-E2 has no swing display.
COOL / FAN / DRY: Setting 1 (Horizontal), HEAT: Setting 5 (Downward 5)
.
.
button and oper-
TEMP
AUTO STOP
AUTO START
h
min
CLOCK
as neces-
Display
1 2 3 4 5
1 2 3 4
.
7