Page 1
Use & Care Guide Manual de Uso y Cuidado English / Español Models/Modelos: 146.29163310/146.29164310/146.29162310 Items / Artículos: 640-05280660-1/640-05280661-9/640-05280658-5 Kenmore Elite ® Liquid Propane Gas Grill Parrilla a gas de propane liquido P/N 30800317 Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A.
Installation Safety Precautions DANGER • Please read this User’s Manual in its entirety before using the grill. • Failure to follow the provided instruction can result in If you smell gas: seriously bodily injury and/or property damage. • Some parts of this grill may have sharp edges. Please wear suitable protective gloves.
. . .39-41 Repair Protection Agreements ® Congratulations on making a smart purchase. Your new Kenmore product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time That's when having a Repair Protection Agreement can save you money and aggravation.
Page 4
WARRANTY Kenmore Elite Limited Warranty When installed, operated and maintained according to all supplied instructions, free in-home warranty service is provided from the date of purchase for the parts, time periods and conditions specified in the list below. Call 1-800-4-MY-HOME ®...
LP Cylinder USE AND CARE • The LP cylinder used with your grill must meet the following requirements: DANGER • Use LP cylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) Capacity maximum.
Page 6
LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to your empty LP tank through an exchange service. Use only those assembly section.) reputable exchange companies that inspect, precision fill, test 2.
Page 7
Leak Testing Valves, Hose and Regulator 1.T T urn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP tank. 3.Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
Page 8
Safety Tips WARNING Before opening LP cylinder valve, check the coupling nut for tightness. When grill is not in use, turn off all control knobs and LP cylinder For Safe Use of Your Grill and to Avoid Serious valve. Injury: Never move grill while in operation or still hot.
Burner Flame Check WARNING • Remove cooking grates and heat diffusers. Light burners, turn knobs from HI to LO. You should see a smaller flame in LO position than seen on HI. Perform burner flame check Turn controls and gas source or tank OFF when not on sideburner, also.
Cleaning the Burner Assembly WARNING CAUTION Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder. SPIDER ALERT! SPIDER ALERT! SPIDER ALERT! 2.
Page 11
Indirect Cooking Food Safety Poultry and large cuts of meat cook slowly to perfection on the grill Food safety is a very important part of enjoying the outdoor by indirect heat. Place food over unlit burner(s); the heat from lit cooking experience.
Page 12
Natural Gas Conversion Kit To purchase Natural Gas Conversion Parts call Sears at 1-800-4-MY-HOME ® Natural Gas Conversion Kit Service Part 30800331 Or In-store part 30611 Item: 590-06109657-4 Your grill can be converted to natural gas with this conversion kit by a qualified gas technician only. To convert this grill the technician will need this conversion kit.
Page 13
Notes Gas Requirements LP Gas For Natural Gas Connection If your grill is for LP Gas, the regulator supplied is set for Preparing: an 11-in. Water column (WC) and is for use with LP gas 1. Turn off gas supply, and then remove cap on gas only.
PARTS LIST Description Part Number Description Part Number End Cap, Right Side Shelf 30800206 33-2 Left Door (Vermillion Red) 30800060C Description Right Side Shelf 30800041 33-3 Left Door (Champaign) 30800060D HEAT DIFFUSERS COOKING GRATE Fascia, Right Side Shelf 30800044 Left Side Panel 30800049 SWING AWAY GRATE Control Panel...
BEFORE ASSEMBLY READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTS FROM SHIPPING BOX. Step 1: Use a box cutter knife to slice down the sides of the carton box. Be careful of staples along the edges. Remove all parts, part boxes, and packing material from the top, sides and bottom of grill head.
Page 17
BEFORE ASSEMBLY Step 2: Tilt grill head up to one side and then to other side to remove large Styrofoam side pieces. Also, remove packing material from regulator hose and igniter wires. Be sure to remove grease tray from left Styrofoam side piece.
BEFORE ASSEMBLY Step 3: With grill head resting on base on shipping box cardboard, raise grill head lid, and remove all part boxes and packing material from inside the grill head. Allow grill head to rest on cardboard until placing grill head on cart during assembly. 18 •...
ASSEMBLY CAREFULLY READ AND PERFORM ALL ASSEMBLY INSTRUCTIONS ON THE FOLLOWING PAGES. Tools Required: Adjustable wrench (not provided) 7/16” Combination wrench (not provided) The following hardware is provided in blister pack for convenient use. M4X10 Screws M4X12 Screws AA Battery Qty: 42 pcs Qty: 1 pc Qty: 2 pcs...
Page 20
Casters to Cart Base Turn cart base upside down. Attach the casters to cart base with (16) M6 X 13 black screws. Casters with brakes attach to rear of cart base. M6X13 screws (Black) Qty: 16 pcs Swivel Casters Panel Front Swivel Caster with Brake Panel Rear...
Page 21
Door Magnets Turn cart base right side up. Attach door magnets to cart base with ( ( 2) M4x10 screws. M4X10 screws Qty: 2 pcs 29163-30800317 21...
Page 22
Side Panels To attach side panel, align holes in panel bottom with holes in cart base. Attach left and right side panels to cart base with ( ( 6) M6x13 gray screws. NOTE: The right panel has four fuel gauge attachment holes. M6X13 screws (Gray) Qty: 6 pcs Fuel Gauge Attachment Holes 22 29163-30800317...
Page 23
Back Panel Attach back panel to cart base and two side panels with ( ( 8) M4x10 screws. M4X10 screws Qty: 8 pcs 29163-30800317 23...
Page 24
Fuel Gauge Attach fuel gauge to right side panel with ( ( 4) M6x13 gray screws from outside to inside of cart Attach ( ( 2) tank positioning pins to right side panel with ( ( 2) M6x13 gray screws. M6X13 screws (Gray) Qty: 6 pcs Tank positioning pins Qty: 2 pcs Positioning Pins...
Page 25
Grease Cup Bracket Attach grease cup bracket to grease cup bracket support with ( ( 2) M4x10 screws. Attach grease cup bracket to left side panel with ( ( 2) M4x10 screws from outside to inside of cart. Attach grease cup bracket support to cart base with ( ( 2) M4x10 screws M4X10 screws Qty: 6 pcs 29163-30800317 25...
Page 26
Door Bracket and Cart Support Angle Bar Align door bracket holes with holes on side panel. Attach bracket to side panels with ( ( 4) M4x10 screws. Align the holes in the cart support angle bar with holes on the cart base and side panels. Attach angle bars with ( ( 8) M4x10 screws.
Page 27
Electronic Ignition Module Unscrew igniter cap and plastic hex nut from Electronic Ignition Module. Secure the Module to the left side panel with nut, and reattach igniter cap. 29163-30800317 27...
Page 28
Grill Head This step requires two people to lift and position grill head onto cart. NOTE: If not previously done, remove packing material from regulator hose and igniter wires. Carefully lower the grill head onto the cart. Make sure the regulator hose and igniter wires are hanging inside the cart.
Page 29
Regulator Retention Bracket Attach the regulator retention bracket to right panel with (2) M4x10 screws. Push the flexible metal tubing up above the fuel gauge and against the side panel to be out of the way of the grease tray. M4X10 screws Qty: 2 pcs 29163-30800317 29...
Page 30
Regulator Hose Hanger Clip Squeeze the hanger clip tips together and insert into the slot in the bottom of the fuel gauge. 30 29163-30800317...
Page 31
Igniter Wire Connection Plug the three small-tipped connectors into the three small sockets in the Electronic Ignition Module. Plug the two large-tipped connectors into the two large sockets in the Electronic Ignition Module. Large-tipped connectors Small-tipped connectors 29163-30800317 31...
Page 32
NOTES Cart Door Remove the ( ( 4) M6x15 screws that are pre-assembled to the door handle ends, and use them to attach handles to doors For each door, insert the bottom hinge pin into the hole in the front bottom of the cart. Push the top hinge pin down into the door, align it with the top hinge pin hole, and let the pin pop back up, securing the door in position.
Side Shelf Assembly (Left Side is Shown) Attach fascia to side shelf with ( ( 2) M5x10 screws, and M M 5 flat washers. ( ( A) Attach end cap to shelf with ( ( 6) M4x10 screws. (B) Hang shelf onto brackets on side of firebox. Attach fascia to control panel with ( ( 1) M4x12 screw (D) Attach shelf to firebox from inside with ( ( 2) M6x13 black screws.
Page 34
Heat Diffusers, Cooking Grate and Warming Rack Place heat diffusers over burners. The heat diffusers will fit in firebox in either direction. Fit tabs in firebox front through slots in diffuser tips. Fit diffuser tips inside tabs in firebox rear. ( ( A) Place cooking grates onto grate rests.
Page 35
Grease Tray Insert Grease Accumulate Panel into cart. Pull igniter wires out of the way to left side of grill. From front of grill, slide grease tray underneath firebox. Make sure grease drainage hole is on left side. Insert the grease cup into the grease cup bracket as shown. Grease Cup 29163-30800317 35...
Page 36
Battery Unscrew the igniter cap from left panel as shown below. Insert (1) AA battery into battery slot with positive (+) facing outward. Screw igniter cap back onto panel. 36 29163-30800317...
Page 37
Safety Notice When the grill in the desired location, lock the caster brakes; this will help the grill stay in place for safe operation. 29163-30800317 37...
Page 38
Gas Tank Installation LP tank is sold separately. Place LP tank onto fuel gauge with tank collar opening facing to the left as shown. Connect the regulator and hose to the tank as shown. CAUTION CAUTION Failure to install grease box will cause Failure to install tank correctly may allow hot grease to drip from bottom of grill gas hose to be damaged in operation.
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Problem Possible Cause Prevention / Solution Gas leaking from •Turn off gas at LP cylinder or at source on natural gas systems. •...
Page 40
Troubleshooting (continued) Prevention / Solution Problem Possible Cause Prevention/Solution Burner(s) will not light ELECTRONIC IGNITION: • See Section I of Electronic Ignition System. using igniter. • No spark, no ignition noise. (See Electronic • See Section II of Electronic Ignition System. Ignition •...
Troubleshooting - Electronic Ignition Check Item Prevention / Solution Problem Possible Cause Preventio • Battery not installed SECTION I • Check battery orientation. • Install battery (make sure that “+” and “-” properly. No sparks appear at connectors are oriented correctly, with “+” end any electrodes when up and “-”...
Page 42
Medidas de seguridad para la instalación PELIGRO • Por favor, lea este manual del usuario en su totalidad antes de usar la parrilla. • El incumplimiento de las enseñanzas impartidas en serio puede resultar en lesiones corporales y / o daños materiales. Si siente olor a gas: •...
Page 43
Símbolos de seguridad ..42 Medidas de seguridad para la instalación ..42 Garantía para la parrilla Kenmore ..44 PROPOSICIÓN 65 DE CALIFORNIA 1. Subproductos de la combustión producidos al usar Uso y mantenimiento .
Page 44
GARANTÍA WARRANTY . . 2 Garantía completa de un año para la parrilla Kenmore KENMORE GRILL WARRANTY . . 2 Garantía limitada de un año de Kenmore Si esta parrilla falla debido a defectos de material o de mano de obra dentro del plazo de un año desde la fecha de...
Page 45
USO Y MANTENIMIENTO Tanque de gas propano PELIGRO • E E l tanque de gas que use con su parrilla debe cumplir los siguientes requisitos: • Use únicamente tanques de gas que tengan las siguientes • N N UNCA guarde los cilindros de gas de repuesto medidas obligatorias: 12"...
Page 46
Cambio del tanque de gas Como conectar el regulador al tanque de gas propano • Muchos comerciantes minoristas que venden parrillas, le ofrecen la opción de cambiar su tanque de gas vacío 1. El tanque de gas debe quedar bien fijado a la parrilla. (Lea la mediante un servicio de recambio.
Page 47
Prueba para detectar fugas de las válvulas, las mangueras y el regulador 1. Gire todas las perillas de control de la parrilla a la posición deAPAGADO. 2. Cerciórese de que el regulador esté bien conectado al tanque de gas. 3. Abra por completo la válvula del tanque, girando la manilla en sonido sentido contrario a las agujas del reloj.
Consejos de seguridad ADVERTENCIA Verifique que la tuerca de unión esté bien apretada antes de abrir la válvula del tanque de gas. Cuando no use la parrilla, cierre todas las perillas de control Para usar su parrilla en forma segura y para y la válvula del tanque de gas.
Page 49
Control de la llama del quemador ADVERTENCIA • Retire las parrillas de cocción y los reguladores de llama. Encienda los quemadores y gire las perillas, de la graduación ALTA (HI) a la graduación BAJA (LO). Deberá ver una llama más reducida en la Gire los controles y la fuente de gas o OFF tanque cuando graduación baja que en la graduación alta.
Page 50
Cómo limpiar la unidad del quemador CAUTION Siga estas instrucciones para limpiar o cambiar piezas de la unidad del quemador, o si tiene problemas para encender la parrilla. 1. Cierre el paso de gas en las perillas de control y desde el ¡ALERTA CONTRA tanque de gas.
Page 51
Cocción indirecta Cocción: Cocine bien las carnes y las piezas de ave, para matar Las aves y los cortes grandes de carne se cocinan lentamente a la las bacterias. Use un termómetro para verificar que los alimentos perfección en la parrilla por calor indirecto. El calor de los alcancen la temperatura interna adecuada.
Page 52
Gas Natural Kit de conversión Para comprar piezas para conversión a gas natural Ilamar a Sears al ® 1-800-4-MY-HOME El gas natural kit de conversión Pieza de repuesto 30800331 O en la tienda de la parte 30611 Item: 590-06109657-4 Su parrilla se puede convertir en gas natural con este Kit de conversión de gas por un técnico cualificado para ello.
Page 53
Notes Requisitos de gas Gas LP Para la conexión de Gas Natural Si su parrilla es para gas LP, el regulador suministrado está Preparación: ajustado para un 11-in. Columna de agua (WC) y es para uso 1. Cierre el suministro de gas y quite la tapa del gas con gas LP solamente.
Page 56
ANTES DE ASAMBLEA LEA Y SIGA LAS INSTRUCCIONES DE ABAJO PARA PARTES DE PARRILLA CORRECTAMENTE desempaquetar caja de envío. Paso 1: Utilice un cuchillo de navaja para cortar los lados de la caja de cartón. Tener cuidado de grapas a lo largo de los bordes. Retire todas las piezas, cajas de partes, y el material de embalaje de los lados superior e inferior de la cabeza de la parrilla.
Page 57
ANTES DE ASAMBLEA Paso 2: cabeza de la parrilla de inclinación hacia un lado y luego al otro lado de derribar grandes piezas laterales de espuma de poliestireno. También retire el material de embalaje de la manguera del regulador y cables de encendido. Asegúrese de retirar la bandeja de grasa a la pieza del lado izquierdo de espuma de poliestireno.
Page 58
ANTES DE ASAMBLEA Paso 3: Con la cabeza apoyada en la base de la parrilla en caja de cartón caja, levante la cabeza cubierta de la parrilla, y eliminar todas las cajas de piezas y el material de embalaje del interior de la cabeza de la parrilla.
Page 59
ASAMBLEA LEA ATENTAMENTE Y REALICE TODAS LAS INSTRUCCIONES DE MONTAJE EN LAS PÁGINAS SIGUIENTES. Herramientas necesarias: Llave ajustable (no incluido) 7/16 "Llave combinada (no incluido) El hardware siguiente se proporciona en un paquete de ampolla para un uso conveniente. M4X10 screw M4X10 countersunk head screw AAA Battery tornillo M4X10...
Page 60
Ruedas a la base del carro Gire la base del carro al revés. Coloque las ruedas en la base del carro con ( ( 16) M6 X 13 tornillos negros. Ruedas con freno adjuntar a la parte posterior de la base del carro. M6x13 tornillos (Negro) Qty: 16pcs Ruedas giratorias Panel frontal...
Page 61
Bolsas de Tela Gire a la cesta de base hacia arriba. Conecte imanes de las puertas de la base del carro con los ( ( 2) tornillos M4x10. Tornillos M4x10 Cantidad: 2 piezas 29163-30800317 61...
Page 62
Paneles laterales Para colocar el panel lateral, alinee los agujeros en la parte inferior del panel con los agujeros en la base del carro. Fije los paneles laterales izquierdo y derecho de la base del carro con (6) tornillos M6x13 grises.
Page 63
Panel posterior Fije el panel trasero a la base del carro y dos paneles laterales con (8) tornillos M4x10. Tornillos M4x10 Cantidad: 8 piezas 29163-30800317 63...
Page 64
Fuel Gauge Coloque el indicador de combustible al panel lateral derecho con (4) t t ornillos M6x13 grises desde el exterior hacia el interior del carro Fije ( ( 2) pasadores de posicionamiento del tanque al panel lateral derecho con ( ( 2) tornillos M6x13 grises.
Page 65
Grasa Copa Bracket Fije el soporte de grasa taza a taza soporte de apoyo grasa con (2) t t ornillos M4x10. Fije el soporte de taza de grasa al panel lateral izquierdo con (2) tornillos M4x10 del exterior al interior del carro. Coloque la bandeja de grasa abrazadera de soporte a la base del carro con (2) t t ornillos M4x10.
Page 66
Soporte de la puerta y Bar cesta Asistencia del ángulo Alinee los orificios del soporte de la puerta con los orificios en el panel lateral. Fije el soporte a los paneles laterales con (4) t t ornillos M4x10. Alinee los orificios del soporte de carro ángulo de soporte con los orificios en la base del carro y los paneles laterales.
Page 67
Módulo de encendido electrónico Desenrosque la tapa del encendedor y la tuerca hexagonal de plástico del módulo de encendido electrónico. Asegure el módulo al panel lateral izquierdo con la tuerca y vuelva a colocar la tapa del encendedor. 29163-30800317 67...
Page 68
Head Grill Este paso requiere de dos personas para levantar y la posición de cabeza de la parrilla sobre el carrito. NOTA: Si no se ha hecho previamente, retire el material de embalaje de la manguera del regulador y cables de encendido. Baje con cuidado la cabeza de la parrilla sobre el carrito.
Page 69
Regulador soporte de retención Acople el soporte de retención del regulador al panel derecho con (2) t t ornillos M4x10. Empuje la tubería de metal flexible por encima del nivel de combustible y contra el panel lateral para estar fuera de la forma de la bandeja de grasa. Tornillos M4x10 Cantidad: 2 unidades 29163-30800317 69...
Page 70
Manguera Regulador Clip Hanger Apriete la punta del clip para colgar e inserte en la ranura en la parte inferior del indicador de combustible. 70 29163-30800317...
Page 71
Conexión del cable de ignición Enchufe los tres conectores pequeño de punta en las tres tomas pequeñas en el módulo de encendido electrónico. Conecte los dos grandes puntas de conectores en los dos zócalos grandes en el módulo de encendido electrónico. Grande con punta de conectores Pequeña punta de conectores 29163-30800317 71...
Page 72
NOTES cesta Door Retire los (4) t t ornillos M6x15 que están pre-ensambladas a los extremos manija de la puerta, y los utilizan para fijar las manijas de las puertas Para cada puerta, inserte el pasador de la bisagra inferior en el agujero en la parte inferior delantera del carro.
Page 73
Side Asamblea Shelf (lado izquierdo se muestra) Adjuntar la fascia de estante lateral con (2) t t ornillos M5x10 y a a randelas planas M5. ( ( A) Coloque la tapa en la repisa con (6) tornillos M4x10 (B) Cuelgue estante en los soportes en el lado de la cámara de combustión. Adjuntar la fascia al panel de control con (1) t t ornillo M4x12 (D) Fije la repisa de la cámara de combustión desde el interior con (2) t t ornillos M6x13.
Page 74
Difusores de calor, Parrilla de cocción Rejilla para calentar y Coloque difusores de calor sobre los quemadores. Los difusores de calor se ajusta en la cámara de combustión en cualquier dirección. Coloque las fichas en frente cámara de combustión a través de ranuras en las puntas del difusor. Montar consejos difusor trasero en el interior de las pestañas cámara de combustión.
Page 75
Engrasar la bandeja Inserte Acumula Grasa Panel en el carro. Tire de los cables del encendedor de en medio a la izquierda de la parrilla. Desde la parte delantera de la parrilla, deslice la bandeja de grasa debajo de la cámara de combustión.
Page 76
batería Desenroscar la tapa del encendedor del panel de la izquierda, como se muestra a continuación. Inserte (1) pila AA en la ranura de la batería con el positivo (+) hacia afuera. Atornille la tapa del encendedor de nuevo en panel. 76 29163-30800317...
Page 77
Freno de la parrilla Cuando la parrilla en la posición deseada, bloquear los frenos de las ruedas, lo que ayudará a la parrilla permanecer en el lugar para una operación segura. 29163-30800317 77...
Page 78
Instalación del tanque de gas tanque de gas se venden por separado Lugar LP tanque sobre indicador de combustible con la abertura del tanque cuello orientado hacia a la izquierda como se muestra. Conecte el regulador y la manguera al tanque como se muestra. CAUTION CAUTION Si no se instala caja grasa hará...
Page 79
EMERGENCIAS: Si no se puede detener una fuga de gas, o si ocurre un incendio debido a una fuga de gas, llame a los bomberos. Emergencias Causas probables Medidas de prevención / solución • Cierre el gas en el cilindro o en la fuente de los sistemas de gas natural. •...
Page 80
Resolucion de problemas (continuacion) Problema Causas probables M M edidas de prevención / solución • Limpie el cable y el electrodo con alcohol de frotar y un hisopo El quemador o los • El cable o el electrodo está cubierto con limpio.
Page 81
Resolución de problemas – Encendido electrónico Problema (encendido) Causas probables Procedimiento de revisión M M edidas de prevención / solución Preventio Causas probables • Revise la orientación de la • Instale la pila (verifique que los polos “+” y “–” •...
Page 82
Get it fixed, at your home or ours! Your Home For troubleshooting, product manuals and expert advice: www.managemylife.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.