Hd color video camera.
st series;u3 series;u2 series;hd baset series (42 pages)
Summary of Contents for minrray UV950
Page 1
Video Conference Video Conference HD Video Video Conference Conference Camera Camera Camera Camera User Manual User Manual User User Manual Manual version version 1.0 version version (English English English English)...
Page 2
Preface: Preface: Preface: Preface: Thanks for using our HD color video conference camera. This manual introduces the function, installation and operation of the HD camera. Prior to installation and usage, please read the manual thoroughly. Warning Warning Warning Warning This product can be only used in specified range in order to avoid any damage or danger;...
Page 4
Notes Electric Electric Electric Electric Safety Safety Safety Safety Installation and operation must accord with electric safety standard Caution Caution Caution to to to to transport transport transport Caution transport Avoid stress, vibration and soakage in transport, storage and installation. Polarity Polarity Polarity of of of of power...
Fast Fast Fast Fast Installation Installation Installation Installation 1. Please check the connection before turning on the power. 2. Bottom Dial Switch Setting Set the two switches 【ON】.It is the normal working mode. SW2-2 SW2- Instructions Undefined Updating mode Debugging mode Working mode...
Page 6
3. The Rotary Switch Setting The choice for16 rotary switch video formats Dial-up 1080P60 1080P50 1080I60 1080I50 720P60 720P50 1080P30 1080P25 -------- -------- -------- -------- -------- -------- -------- Display the video format set on the menu Note: Restart the camera after switching the dial code. 4.When the power supply switch is “【on】”, the indicator light is open (red color) 5, Camera initializes after powering on: horizontally turn left to the limit position, vertically turn to the bottom;...
Page 7
Camera Camera Highlights Highlights Camera Camera Highlights Highlights 1.Equipped with modern appearance and 12X HD CMOS sensor, delivering vivid images. 2.Support DVI interface (inclding YPbPr, VGA and HDMI signal), HD-SDI interface and CVBS interface (for options). 3. IR remote controller signal transparent transmission function: camera can receive both its own remote controller signal and the one from terminal equipment, by transmitting the signal through VISCA IN to terminal equipment IR receiver.
Page 8
Camera Camera Interface Interface Explanation Explanation Camera Camera Interface Interface Explanation Explanation 1.Camera lens 2.Camera base 3..Remote Controller Receiver light 4.Bottom dial Switch 5.Tripod screw hole 6.Installation Orientation Hole 7.Rotary Switch : video format optional 8.RS232 controller serial interface (input ) 9.RS232 controller serial interface (output ) 10.CVB interface (for selection) 11.HD-SDI interface...
Remote Remote Controller Controller Explanation Explanation Remote Remote Controller Controller Explanation Explanation Definition Definition of of of of IR IR IR IR controller controller Definition Definition controller controller 0 0 0 0 、Standby Standby Standby Standby key After pressing the standby key, the camera will step into standby mode.
Page 10
key :Down Press key :Left Press Press key:Right “HOME” key: Return to the middle position 9 9 9 9 、Menu Menu Menu Menu setting setting setting setting Open or close the OSD menu Zoom Zoom Control Control 10、Zoom Zoom Control Control key zoom+:Lens near zoom-:Lens far...
Page 11
press Down: press Left: press Right: press Back to middle position:press“【HOME】” Press and hold the up/down/left/right key, the pan/tilt will keep running, from slow to fast, until it runs to the endpoint; the pan/tilt running stops as soon as the key is released. 2.
Page 12
4. 4. 4. 4. BLC Setting Setting BLC Setting Setting BLC ON / OFF: not support 5. 5. 5. 5. Presets Presets Presets setting setting Presets setting setting 1 、 Preset setting : to set a preset position, the users should press the “ 【 SET PRESET 】...
Page 14
VISCA VISCA Function Function VISCA VISCA OUT OUT Function Function VISCA VISCA Function Function VISCA VISCA OUT OUT Function Function control control COM control control In the normal working condition, the camera can be controlled via the RS-232C/RS485 command (VISCA IN). The parameter of the RS232C COM is as follows: Baud Rate :2400/4800/9600/115200 Bit/S Start bit:1bit;...
Page 16
Command Command Function Function Command Command Packet Packet Note Note Command Command Function Function Command Command Packet Packet Note Note Direct 8x 01 04 43 00 00 0p 0q FF pq: R Gain Reset 8x 01 04 04 00 FF 8x 01 04 04 02 FF Manual Control of B Gain CAM_Bgain...
Page 17
Command Command Function Function Command Command Packet Packet Note Note Command Command Function Function Command Command Packet Packet Note Note 4:720P60 5:720P50 6:1080P30 7:1080P25 CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs: Camera ID (=0000 to FFFF) SYS_Menu 8x 01 06 06 03 FF Turn off the menu...
Menu Menu Setting Setting Menu Menu Setting Setting 1. 1. 1. 1. Main Main Main Menu Menu Main Menu Menu In normal working mode, press 【MENU】key to display the menu, using scroll arrow to point at or highlight the selected items. LANGUAGE LANGUAGE LANGUAGE...
Page 21
PROTOCOL PROTOCOL PROTOCOL PROTOCOL:Defaulted Setting: VISCA Type of Protocol: VISCA/Pelco-P/Pelco-D ADDR ADDR ADDR ADDR:Defaulted Setting: 01 VISCA=1~7 Pelco-P/Pelco-D = 1~155 B. B. B. B. RATE RATE RATE RATE: : : : Defaulted Setting: 9600 2400/4800/9600/115200 RS485 RS485 RS485 RS485:Defaulted Setting: OFF It is ON when using RS485 communication ARM...
Page 22
EXP. EXP. MODE MODE EXP. EXP. MODE MODE:Defaulted Setting: Auto For Settings: Auto, Manual, Shutter, Iris SHUTTER SHUTTER SHUTTER SHUTTER:Defaulted Setting: Default For Settings: 1/60, 1/90, 1/100, 1/125, 1/180, 1/250, 1/350, 1/500, 1/725, 1/1000, 1/1500, 1/2000,1/3000,1/4000,1/6000,1/1000(only available in Manual Shutter mode) IRIS IRIS IRIS...
Page 23
For Settings: 0~3 SATURATION SATURATION SATURATION SATURATION:Defaulted Setting: 4 For Settings: 0~9 APERTURE APERTURE APERTURE APERTURE:Defaulted Setting: 2 For Settings: 0~9 FLICK FLICK FLICK FLICK:Defaulted Setting: 50HZ For Settings: 50HZ/60HZ/OFF LEVEL LEVEL NR LEVEL LEVEL: Defaulted Setting: 6 For Settings: 0~9 CONTRAST CONTRAST CONTRAST...
Page 24
power on), off SPEEDBYZ SPEEDBYZ SPEEDBYZ SPEEDBYZ:Defaulted Setting: On only work for IR remote control, On ( when the camera zoom becomes larger, rotation speed comes down), Off MOUNT.MODE MOUNT.MODE MOUNT.MODE MOUNT.MODE: Defaulted Setting: UP For Setting: UP, DOWN IR IR IR IR M.SPEED M.SPEED M.SPEED M.SPEED:...
Page 25
7. 7. 7. 7. EXIT EXIT EXIT EXIT In main menu, press the key【MENU】again will show the exit window as follows: EXIT EXIT EXIT EXIT ================ SAVE SAVE SAVE SAVE? Yes/No Yes/No Yes/No Yes/No OK/HOME BACK BACK BACK BACK/MENU SAVE SAVE SAVE SAVE?:to save settings:Yes, No.
Troubleshooting Troubleshooting Troubleshooting Troubleshooting Camera Maintains Camera Camera Camera Maintains Maintains Maintains If camera is not used for long time, please turn off power adapter switch and AC plug. Use soft cloth or tissue to clean the camera cover. Use soft cloth to clean the lens; Use neuter cleanser if bad smeared. No use strong or corrosive cleanser or corrosive cleanser avoiding scuffing.
Need help?
Do you have a question about the UV950 and is the answer not in the manual?
Questions and answers