Starting Setup; Tv Operation - Hitachi LE40S508 Owner's Manual

Starting setup
The Setup Wizard appears the first time you turn on the TV,
and assists you to specify the Air/Cable setting, and program
your channels automatically.
iMPORTANT: Make sure that the antenna or cable TV system
connection is made.
1 To turn on the TV, press POWER. (it may take approx. 10
seconds for a picture to appear on screen.) The initial Setup
Wizard begins.
2
3
4
5
6
7
8
Select your "TV Mode" by pressing A or T to select "Home"
or "Retail". This product qualifies for ENERGY STAR in Home
mode with its default settings.
NOTE:
Retail mode is intended for in-store display and resets video
settings each time TV is turned on.
Press _ to go to the next step.
Press A or T to your desired language, then press =- to go to
the next step.
Press A or T to select your time zone, then press _.
, In the rare event that you live within broadcast range of two
stations in two different time zones, theTV may recognize
the wrong station for the auto clock set.
Press A or T to your desired time format, then press =-.
Press A or T to select signal type that you using, then press
Auto Channel Scan will begin. After the scan is completed,
aTV channel appears on the screen.
Depending on the reception condition, it may take up to 30
minutes to complete scanning channels. Please allow the
process to complete without interruption.
NOTE:
• If you press EXIT during the "Auto Channel Scan" process, the
Auto Channel Scan will stop and the TV will change to the normal
view.
• When you make a menu selection, your changes occur
immediately. You do not have to press EXIT to see your changes.
TV operation
1
2
3
4
To turn on the TV, press POWER. (It may take approx.10
seconds for a picture to appear on screen.)
Adjust the volume level by pressing VOL (VOLUME) + or -.
The volume level will be indicated on the screen by a volume
bar.
If the volume increases, the number of bars also increases.
If the volume decreases, the number of bars also decreases.
Set the Source option to the appropriate selection (see "Air/
Cable selection" on page 18).
Press the Direct Channel Selection Buttons (0-9, -) to
select the channel.
TO SELECT ANALOG CHANNELS
1-9: Press t-9 as needed. Example, to select channel 2,
press 2, then press SELECT..
10-99: Press the 2 digits in order. Example, to select
channel 12, press 1,2, then press SELECT.
100-135: Press the 3 digits in order. Example, to select
channel 120, press 1,2, 0, then press SELECT.
TO SELECT DIGITAL CHANNELS
Press the first digits, then press the - button followed by the
remaining number.
Example:To select channel 15-1, press 1,5, -, 1, then press
SELECT.
, If a channel is selected with only audio content, "Audio Only"
will be displayed on the screen.
• If a channel is selected with a weak digital signal, "Weak or
No Signal" will be displayed on the screen.
The same program may be available on either an analog
channel or a digital channel.You may choose to watch
either format.
Air
VHF
2-13
UHF
14-69
VHF/UHF/CABLE CHANNELS
Cable
VHF
2-13
STD/H RC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-l)
100-135 (100)(135)
01 (4A)
NOTE:
, If a channel with no broadcast is selected, the sound will
automatically be muted.
, It may take a few seconds for a digital channel picture to appear
on screen after being selected.
To select the video input source
To view a signal from another device connected to your TV, such
as aVCR player, press INPUT, then press A or T to select the
desired input, then press SELECT.