Sony MXD-D5C Service Manual page 82

Pin No. Pin Name
45 SPDL MUTE
46 to 51
NC
52 LED RECMODE
53 LED DATA
54 LED CLK
55 XLED STB
56 to 60
NC
61 XDISP RST
62 VCC
63 STB
64 VSS
65 JOGCD0
66 JOGCD1
67 JOGMD0
68 JOGMD1
69 to 71 NC
72
SPDIF CUT
73 LOD POS
74 LOD NEG
75 OUT SW
76 MIDOUT SW
77 IN SW
78 MIDIN SW
79 CLP POS
80 CLP NEG
81 INIT SW
82 COUNT SW
83 E3
84 E1
85 E2
*1 CD loading motor (M702) control
Mode
Loading
Terminal
"L"
LOD NEG (pin uf)
"H"
LOD POS (pin ud)
82
I/O
O
Spindle motor muting control signal output to the CD block
O Not used (open)
O LED (D951 MDLP) on/off control signal output
O LED control serial data output to the LED driver (IC902)
O LED control serial data transfer clock signal output to the LED driver (IC902)
O LED control strobe signal output to the LED driver (IC902)
O Not used (open)
O Reset signal output to the display controller (IC805)
— Power supply terminal (+5V)
O
Strobe signal output to the power supply circuit "L": standby mode, "H": power on
— Ground terminal
I
Jog dial pulse input from the rotary encoder (S971 l AMS L (CD)) B phase input
I Jog dial pulse input from the rotary encoder (S971 l AMS L (CD)) A phase input
I Jog dial pulse input from the rotary encoder (S981 l AMS L (MD)) B phase input
Jog dial pulse input from the rotary encoder (S981 l AMS L (MD)) A phase input
I
O Not used (open)
O Not used (open)
CD loading motor (M702) control signal output to the motor driver IC (IC702)
O
"L" active *1
CD loading motor (M702) control signal output to the motor driver IC (IC702)
O
"L" active *1
Detection input from the tray open/close detect switch (S708) on the CD mechanism block
I
"L": when tray is open, "H": when tray is close
Detection input from the mid out detect switch (S701) on the CD mechanism block
I
"L": when tray is going to open or close
Detection input from the tray open/close detect switch (S704) on the CD mechanism block
I
"L": when tray is close, "H": when tray is open
Detection input from the mid in detect switch (S703) on the CD mechanism block
I
"L": when sub tray move between tray and stocker
CD elevator up/down motor (M701) control signal output to the motor driver IC (IC701)
O
"L" active *2
CD elevator up/down motor (M701) control signal output to the motor driver IC (IC701)
O
"L" active *2
Detection input from the INIT detect switch (S705) on the CD mechanism block
I
"L": when elevator down to bottom, others: "H"
Detection input from the count detect switch (S706) on the CD mechanism block
I
"L": when elevator up/down each sub tray stock position
I
Detection input from the disc tray address detect rotary encoder (S707) on the CD mechanism
I
block
I
Eject Stop Brake
"H" "H" "L"
"L" "H" "L"
Description
*2 CD elevator up/down motor (M701) control
Mode Elevator
Up
Terminal
"L"
CLP NEG (pin i;)
"H"
CLP POS (pin ul)
Elevator
Stop Brake
Down
"H" "H" "L"
"L" "H" "L"