CD SECTION
Set the CD test mode when performing confirmations.
After completing confirmation, release the CD test mode. (Turn the
[
AMS
]
(MD) knob so that the power is turned off.)
l
L
1. COMMAND TRANSFER MENU
Procedure:
(1) Enter the test mode, then rotate
knob.
(2) Select a command with
(3) Select the edit position with
[
AMS
]
(MD) knob for transfer.
l
L
(4) To exit from this mode, press the
2. C1, C2 ERROR DISPLAY
Procedure:
(1) Enter the test mode, then rotate
(2) C1 error and C2 error are displayed on the left side and right side with 4-digit codes respectively.
(3) To exit from this mode, press the
3. DISC SPEED SELECTION
Procedure:
(1) Enter the test mode, then rotate
[
AMS
(2) Each time the
l
(3) To exit from this mode, press the
4. CHECK 8 DISPLAY
Procedure:
(1) Enter the test mode, then rotate
(2) The time from spindle kick to GFS detect is displayed.
(3) To exit from this mode, press the
5. PORT SELECTION
Procedure:
(1) Enter the test mode, then rotate
[
AMS
(2) Rotate the
l
(3) To exit from this mode, press the
6. AMS ON/OFF
Procedure:
(1)
Enter the test mode, then rotate
(2) Switch the high speed ON/OFF of the track jamp.
(3) To exit from this mode, press the
7. TRK ON/OFF
Procedure:
(1) Enter the test mode, then rotate
(2) Switch the tracking servo ON/OFF.
(3) To exit from this mode, press the
34
[
AMS
]
(MD) knob to display "0> COMMAND", and press the
l
L
[
AMS
]
(MD) knob, and press the
l
L
m
(MD) and
M
(MD) buttons, and rotate
[MENU/NO]
button.
[
AMS
]
l
L
(MD) knob to display "1> ERROR", and press the
[MENU/NO]
button.
[
AMS
]
l
L
(MD) knob to display "2> SPEED X1", and press the
]
(MD) knob is pressed, the speed changes over such as x1 t x2 t x4 t x1.
L
[MENU/NO]
button.
[
AMS
]
l
(MD) knob to display "4> CHECK8", and press the
L
[MENU/NO]
button.
[
AMS
]
l
L
(MD) knob to display "7> PORT", and press the
]
(MD) knob to select GFS, ERROR RATE, RFCK and press the
L
[MENU/NO]
button.
[
AMS
]
l
L
(MD) knob to display "8> AMS ON", and press the
[MENU/NO]
button.
[
AMS
]
(MD) knob to display "9> TRK ON", and press the
l
L
[MENU/NO]
button.
[
AMS
]
l
L
(MD) knob, "<8> Initial" displayed and press the
[
AMS
]
(MD) knob to set.
l
L
[
AMS
l
L
[
AMS
l
L
]
(MD) knob for editing, then press the
[
AMS
]
l
L
(MD) knob.
[
AMS
]
l
L
(MD) knob.
[
AMS
]
l
L
(MD) knob.
[
AMS
]
l
L
(MD) knob.
[
AMS
]
(MD) knob to set.
l
L
[
AMS
]
l
L
(MD) knob.
[
AMS
]
l
L
(MD) knob.
]
(MD)