All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 470 Service PaCE...
EN 2 DPTV465 Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview 1.1.4 Technical Specifications Miscellaneous : +5/+45 °C Ambient Temperature 1.1.1 Reception : 160 - 276 V_ac (only / Mains Voltage : PLL Tuning System...
Page 3
Technical Specifications, Connections, and Chassis Overview DPTV465 EN 3 1.2.3 AV1 (Hosiden: SVHS - In) Side Jack Panel 43” and 55” Ground Ground 43” 55” 1.0 Vpp / 75 ohm 0.3 Vpp / 75 ohm AV1 (Cinch) Ye - Video (CVBS) 1.0 V_pp / 75 ohm...
Page 4
EN 4 DPTV465 Safety and Maintenance Instructions, Warnings, and Notes 2. Safety and Maintenance Instructions, Warnings, and Notes Safety Instructions Warnings • Safety regulations require that during a repair: In order to prevent damage to ICs and transistors, avoid all •...
Directions for Use DPTV465 EN 5 • The semiconductors indicated in the circuit diagram and in the parts lists, are interchangeable per position with the semiconductors in the unit, irrespective of the type indication on these semiconductors. • Manufactured under license from Dolby Laboratories.
EN 6 DPTV465 Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Disassembly Procedures 1. Disassembly Procedures 2. Service Position All numbers, found in the following text, refer to the drawing 3. Picture Tube Replacement below and apply to both the 43” and 55” models.
Page 7
Mechanical Instructions DPTV465 EN 7 4.1.1 1. Carefully pull the ACS panel upward to separate it from the Lower Center Back Cover Removal (86) SSM connectors. 2. Disconnect the cable assemblies. 1. Remove all screws (B and C). 2. Remove the Lower Center Back Cover.
Page 8
EN 8 DPTV465 Mechanical Instructions Service Position removal of these components could result in fluid spillage into the PTV cabinet. 8. Carefully remove the CRT/Lens assembly from the PTV 1. Remove the Side Back Covers. cabinet. 2. Remove the Front Speaker Baffle.
Page 9
Mechanical Instructions DPTV465 EN 9 dryer may be used to dry the coupler and its assemblies the top of the coupler at the plug. Wipe any excess fluid before reassembly. If contaminated fluid is discovered, the from around the coupler.
Customer Service Mode (CSM) is used for communication • Access to normal user menu: Pressing the "MENU" button between a Philips Customer Care Centre (P3C) and a on the remote control switches between the SDM and the customer. normal user menus (with the SDM mode still active in the background).
Page 11
Service Modes, Error Codes, and Fault Finding DPTV465 EN 11 The functionality of the OPTIONS and ALIGNMENTS (TUNER, WHITE TONE, GEOMETRY, SOUND, and SMART SETTING) sub-menus are described in the "Alignments" section (chapter HRS: 1228 SWID: HDR: 1AP1-5.15 ERR: 0 0 0 0 How to exit SAM To exit the Service Alignment Mode, enter ”0”...
Page 12
EN 12 DPTV465 Service Modes, Error Codes, and Fault Finding • • Line 2 : "CODES : xx xx xx xx xx xx xx "; Error code Line 17 : "CONTRAST"; Value indicates level at CSM buffer (see explanation of error codes above) Displays the entry.
Page 13
Service Modes, Error Codes, and Fault Finding DPTV465 EN 13 without a Dolby Signaling bit, this indicator will show “OFF” 2/0 LtRt”, “MPEG 2/1”, “MPEG 2/2”, “MPEG 3/0”, “MPEG even though a Dolby transmission is received. 3/1”, “MPEG 3/2”, “MPEG 1+1” or “MPEG 2+2”.
Page 14
1. Press 'Smart Picture' button on the RC-transmitter. In case the picture improves, increase the 'Brightness' or the ComPair (Computer Aided Repair) is a service tool for Philips 'Contrast' value. The new value(s) are automatically stored Consumer Electronics products. ComPair is a further (in 'personal' pre-set) for all TV channels.
Page 15
Service Modes, Error Codes, and Fault Finding DPTV465 EN 15 • By a combination of automatic diagnostics and an interactive By exiting SDM or SAM with the "Standby" command on question / answer procedure, ComPair will enable you to find the remote control.
Page 16
EN 16 DPTV465 Service Modes, Error Codes, and Fault Finding Note: Error codes 1,2, 3, and 4 are protection codes, and in this line will be approximately 2.6 Volts in standby and zero Volts case, the supplies of some circuits will be switched "off". Also, when the set is turned "on".
Circuit Diagrams and PWB Layouts45 DPTV465 7. Circuit Diagrams and PWB Layouts45 Power Supply Panel: AC Input AP AC INPUT AP To SSM = 160V to 329V Depending on Mains Input Panel 1102 1102 120V Mains = 152V to 166V...
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module SMALL SIGNAL MODULE TO 3D COMB 3028 2095 8.8V 7017 2103 F126 F125 CXA2089S I150 I151 I154 I155 I157 2091 100n 8.8V 3-B9,2-H7 3.9V 5 TV VOUT1 46 3.6V VOUT1 2092...
Page 31
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) I241 F225 1024-11 1029 8.5V SUB_WOOF YKC21-2921 YKC21-3416 8-C12 I217 F226 2104 3144 F200 8.8V F201 3045 I240 6031 6030 AV1-L 3073 100n 1-D2 3142 2822...
Page 32
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) 500mV / div AC 10µs / div I321 I322 I319 3304 8-G8 V-SSB-N RTXT I344 7.4V 6-B2 5.4V I318 I341 6.8V BC857B BC857B 4.8V I316 I340...
Page 33
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) 7045 STK392-120 I438 F407 35.6V 5-D12 5 PRE_POS VccPSW-V +35V 6-H11,5-A1 F406 I436 F404 F405 MUTING -35.8V -.1V CH1_IN_POS CH1_OUT I412 -35V -.1V 7 CH1_IN_NEG 6-G11,5-I12,4-I5...
Page 34
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) +22V 6-H11 +35V 6-H11,4-A1 VccPSW-H 4-D1 I521 GND-C 3199 7010 BC817-25 7020 6042 I519 GND-C GND-C IRF9Z24N 7019 7009 3198 BC817-25 BC847B I509 I520 7021 BAS216...
Page 35
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) TO ACS CONTROL TO WB/HOP 3075 +5V_STBY 6-H10,6-G2 3076 5001 3068 7026 BC847B 330R 4020 7025 1001 4021 6-C8 BC847B I638 15JL-BT-E 4022 4023 6-C8 2031...
Page 36
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) I725 I730 3715 3708 5.2V 5.2V I714 5.1V BC857B 7705 5.2V 7706 BC847B 3706 3798 3730 5.2V I726 .04V 100R 3714 .06V I727 7704 I709 7710 .04V...
Page 37
Circuit Diagrams and PWB Layouts45 DPTV465 Small Signal Module: AP SMALL SIGNAL MODULE (AP) 3412 USED WITH SUB-WOOFER MODELS ONLY I815 2414 100p 4.9V F805 F809 I813 F802 2411 3422 INA_NEG I816 F808 HEADPHONE_L F804 I819 6-F3 2467 2440 2.4V...
Circuit Diagrams and PWB Layouts45 DPTV465 CRT Panel: Red D(R)1 D(R)1 RED CRT PANEL 1202 EH-S To HOP Panel 200mV / div AC 100mV / div AC 100mV / div AC 100mV / div AC 1V / div AC 1V / div AC...
Circuit Diagrams and PWB Layouts45 DPTV465 CRT Panel: Green D(G)1 D(G)1 GREEN CRT PANEL 1202 EH-S To HOP Panel 1720 To LSP Panel 1202 200mV / div AC 100mV / div AC 100mV / div AC 1V / div AC...
Circuit Diagrams and PWB Layouts45 DPTV465 CRT Panel: Blue D(B)1 D(B)1 BLUE CRT PANEL 1202 EH-S 200mV / div AC 100mV / div AC 100mV / div AC 1V / div AC 1V / div AC 1V / div AC...
Page 47
Circuit Diagrams and PWB Layouts45 DPTV465 Mapping CRT Panel: Red, Green, and Blue Personal Notes: E_06532_012.eps 131004 E150000_135.eps 191004...
Page 49
Circuit Diagrams and PWB Layouts45 DPTV465 Large Signal Panel HDR2K4 LARGE SIGNAL PANEL (AP) 0033 2390 HEATSIN K I164 120V Mains = 152V to 166V 220V Mains = 233V to 316V 470p To Power F111 56.5V 81.2V I111 I166 2323...
Page 50
Circuit Diagrams and PWB Layouts45 DPTV465 Large Signal Panel HDR 2K4 LARGE SIGNAL PANEL (AP) 0085 I810 HEATSINK 2805 470p I811 I812 F800 3801 1801 6801 6.8V NEG-HORIZ-PULSE FILAMENT 2-L10 2-K1 0R68 BY229X-200 50V / div AC 500mV / div AC 10µs / div...
Page 51
Circuit Diagrams and PWB Layouts45 DPTV465 Large Signal Panel HDR2K4 LARGE SIGNAL PANEL (AP) VFOC EHT EHT 5904 I910 I912 5902 +130VHV TRANSFORMER DRIVER & CONTROL VAUX ON / ABL RTN VAUX TEST OFF GND NC NC 1504 B3P-LV-TA 2.1V...
Page 52
Circuit Diagrams and PWB Layouts45 DPTV465 Mapping Large Signal Panel E1-E3 (Part 1) KDR2K4 LARGE SIGNAL PANEL (AP) E_15000_028.eps 3135 033 3425.3 131004...
Page 53
Circuit Diagrams and PWB Layouts45 DPTV465 Mapping Large Signal Panel E1-E3 (Part 2) Personal Notes: HDR2K4 LARGE SIGNAL PANEL (AP) E_06532_012.eps E_15000_029.eps 3135 033 3425.3 131004 191004...
Page 55
Circuit Diagrams and PWB Layouts45 DPTV465 Layout Large Signal Panel (Bottom Side) 2822 G3 2829 F1 2843 C1 2904 A2 2915 C2 2927 E1 3313 A10 3318 B10 3328 D11 3363 G5 3384 F6 3823 F1 3833 E2 3842 D1...
Page 56
Circuit Diagrams and PWB Layouts45 DPTV465 Side Jack Panel A10PTV SIDE JACK PANEL Ref Des 3135_037_10581 3135_037_12321 RESERVED 4000 1002-A 242202604926 NOT USED NOT USED F015 YKF51-5347 1002-B 1002-B 242202604926 NOT USED NOT USED 1002-A YKF51-5347 YKF51-5347 F014 2000 YKF51-5347...
Page 57
Circuit Diagrams and PWB Layouts45 DPTV465 Mapping Side Jack Panel G1 Personal Notes: A10PTV SIDE JACK PANEL E_06532_012.eps E_15000_033.eps 3135 033 3217.4 131004 191004...
Page 58
Circuit Diagrams and PWB Layouts45 DPTV465 Layout Side Jack Panel (Top Side) Layout Side Jack Panel (Bottom Side) 2000 A1 2001 B1 1001 B1 2002 B1 1002 A1 2005 B1 1007 C1 2006 B1 1335 B1 2008 C1 1337 C1...
Page 65
Circuit Diagrams and PWB Layouts45 DPTV465 HOP Panel HDR2K4 HOP 28KHZ AP AUG 1720 EH-B 1710 EH-B 1700 EH-B To Blue To Green To Red CRT Panel CRT Panel CRT Panel 1210 1210 1210 B-BIAS +12V 7800 F722 F712 F702...
Page 66
Circuit Diagrams and PWB Layouts45 DPTV465 HOP Panel HDR2K4 HOP 28KHZ ( AP) +12V 1111 2509 100n +5VA 2511 3511 7511 2V / div AC 2V / div AC 200mV / div AC 200mV / div AC 500mV / div AC...
Page 67
Circuit Diagrams and PWB Layouts45 DPTV465 Diversity HOP Panel J1 and J2 Personal Notes: HDR2K4 HOP 28KHZ AP AUG N3 HOP DB15 N3 HOP W/O DB15 RESERVED RESERVED N3 HOP DB15 N3 HOP W/O DB15 Ref Des 3135_037_12781_01 3135_037_12791_01 RESERVED...
Page 68
Circuit Diagrams and PWB Layouts45 DPTV465 Mapping HOP Panel J1 and J2 Part 1 HDR2K4 HOP 28KHZ AP AUG E_15000_045.eps 3135 033 3429.2 111004...
Page 69
Circuit Diagrams and PWB Layouts45 DPTV465 Mapping HOP Panel J1 and J2 Part 2 Personal Notes: HDR2K4 HOP 28KHZ AP AUG E_06532_012.eps E_15000_046.eps 3135 033 3429.2 191004 131004...
Alignments DPTV465 EN 77 8. Alignments 5. Repeat steps two through four to adjust the focus of the two Index of this chapter 1. General alignment conditions remaining CRTs. 2. Hardware alignments 3. Software alignments Note: Before beginning the following adjustment procedures 4.
Page 78
EN 78 DPTV465 Alignments 1. During the IF AFC-parameter adjustment, one can see • LUM. DELAY PAL BG: Apply a PAL BG colour bar / grey OSD feedback on the screen. scale pattern as a test signal. Adjust this parameter until 2.
Page 79
Alignments DPTV465 EN 79 3. Grey Scale (White Tone). After entering the default values, the E-W WIDTH, VERTICAL SLOPE, and VERTICAL AMP should be the only settings If the SSM (Small Signal Module has been changed: requiring further adjustment. 1. Convergence.
Page 80
EN 80 DPTV465 Alignments CURSOR RIGHT CURSOR KEYS TO ADJUST MENU CURSOR KEYS TO NAVIGATE MENU TO CHANGE MENU TO ADJUST STEP SIZE I+ TO RETURN I+ TO RETURN GREEN RED TO GREEN BLUE TO GREEN GREEN TO RED BLUE TO RED...
Page 81
Alignments DPTV465 EN 81 8.4.7 Touch Up Convergence When the GREEN geometry is complete, STORE the data. Remove the template from the screen. Select RED TO GREEN in the selection menu. Using the same method that was used When making minor Convergence corrections, move the...
Page 82
EN 82 DPTV465 Alignments – 8.5.4 WARM DRIVE BLUE: “-6” Option Codes 15.Press the MENU button to return to the SAM menu. Exit the Service mode by turning the set ”off”. Enter the Service Alignment Mode (SAM) by pressing the following key sequence on the remote control transmitter: 0-6-2-5-9-6-[i+].
Auto Multi Voltage sets have a voltage Table 9-1 Model and chassis overview range of 90 to 276 V. Model Chassis Aspect Ratio Destination Table 9-2 Voltage range overview 43PP8445/93 DPTV465 China 43PP8446/93 DPTV465 China Model Voltage Range 43PP8447/93 DPTV465...
Page 84
EN 84 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.2.2 AC Input Board E_15000_067.eps 151004 Figure 9-2 AC input board The AC power is fed to the AC Input panel. A 5 A fuse (item Bridge 6001 rectifies the voltage for the Standby Power supply.
Page 85
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 85 In Standby, the-5 volt Standby voltage is the only voltage being Under voltage Detection applied to the set. The +15, +9, and +5.2 Volt sources are turned "off". When the set is turned "on", the Standby Line goes Low, turning transistor 7214 "off", turning 7205 "on", which...
Page 86
EN 86 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets sets the reference voltage for comparator "B", which is Power Fail Shutdown compared with the voltage on the source of 7301. This voltage is developed when 7301 turns "on", causing current to flow through resistors 3308 and 3309.
Page 87
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 87 9.3.2 doubler circuit on the SSB, called the Feature Box, changes the SSM composite Inputs interlaced 625 or 525 signal to a Progressive Scan 480p, 576p, 100Hz, or 120 Hz signal. This YUV signal is buffered and fed to the SSM where it is buffered before being fed to the HOP (High end Output Processor) panel.
Page 88
EN 88 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.3.4 9.3.5 SSB Video Switching SAW Filter Switching E_15000_077.eps 181004 Figure 9-12 SAW filter switching circuit The HDR2K3 AP set has a Multi-System tuning system. Since NTSC uses a 6 MHz bandwidth and PAL/SECAM uses an 8 MHz bandwidth, it is necessary to have separate SAW filters.
Page 89
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 89 9.3.7 9.3.9 Sound Trap Switching Double Window PIP E_15000_079.eps 181004 Figure 9-14 Sound trap switching circuit Composite video is output on pin 10 of 7323 and buffered by transistor 7411.
Page 90
EN 90 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.3.11 Double Window Control and Power Supply Switching The PIP or Double Window YUV signal is fed to the PIP/DW processor, 7801. The I2C buss controls the IC from the microprocessor on the SSB.
Page 91
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 91 The circuit located on the SSB labelled the Feature Box available. The signal is converted to an analogue format and performs the digitising, line doubling, and picture resizing. The output on Pins 54, 63, and 73.
Page 92
EN 92 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.3.16 HOP Signal Processing E_15000_088.eps 181004 Figure 9-23 HOP signal processing 9.3.17 HOP Sharpness Control The Y/G, B/Pb, and R/Pr signals are fed to their respective sharpness controls. If the input is a YUV signal, the Y signal is fed to pin 28 of 7600.
Page 93
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 93 signal, it is amplified by 7412 and buffered by 7413. If the input Green and Red CRTs, the inverting input on pin 2 will become was a U signal, it is buffered by 7414.
Page 94
EN 94 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets Sync from the SSB. For separate Horizontal and Vertical Sync, 7210 turns the Sync Separator "off". The Sync output on pin 17 the output of 7210 is fed to the multiplexer IC 7330, which is is fed to a Low Pass Filter, which separates the Vertical Sync.
Page 95
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 95 9.3.25 High Voltage Circuit E_15000_097.eps 181004 Figure 9-32 High voltage circuit The High Voltage module is an integrated High Voltage supply produce a 375 Volt source for the Dynamic Focus drive. The with its own switching power supply.
Page 96
Convergence processor Intellisense Sensor Locations E_15000_100.eps 181004 Figure 9-35 Sensor locations The Philips Intellisense system makes minor Convergence E_15000_099.eps corrections when the feature is selected by the Customer. 181004 When a PTV is moved from one location to another, minor...
Page 97
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 97 Intellisense Sensing Circuit E_15000_101.eps 181004 Figure 9-36 Intellisense circuit The output of the four sensing Solar Cells are fed to IC 7141 18. The IC is powered by four supply inputs. A +35 Volt supply located on the ACS module.
Page 98
EN 98 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets up circuit senses a negative 10 to 12 volt drive to the Vertical Left and Right audio is output to a Headphone Amplifier located Convergence yokes, the VccNSW-V supply will switch from - on the SSM.
Page 99
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 99 9.4.5 The Audio Amplifier is located on the SSM. The output power Centre Channel Amp Switch for the Audio Amplifier is 10 Watts per channel for the Basic and Basic Plus versions.
Page 100
EN 100 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets Control/OSD 9.5.1 Microprocessor SENSOR +3.3V BOARD 1201 1014 1020 KEYBOARD 23-37 7010 7100 STBY 7001 CONTROL 7006 ON/OFF 7012 7007 PROGRAM DRAM FLASH FLASH-RAM STANDBY SDA-B CONV LIGHT...
Page 101
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 101 9.5.3 Light Sensor The Light Sensor, 6104, is amplified by two op amps in 7000. This circuit senses the ambient light and outputs a voltage on pin 7 of 7000. This voltage is fed to the OTC, which makes...
EN 102 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.5.5 On-Screen Display List of Abbreviations 16:9-ARFRONT 16:9 aspect ratio input from side jack panel 50Hz/60Hz 50Hz/60Hz AC frequency 6-CHANNEL DAC 6-Channel DAC Auto Convergence System Automatic Frequency Control...
Page 103
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 103 DAC-HOP Digital analogue converter HOP IC HEATER Heater (Filament) DC_PROT/ Horizontal flyback AUDIO_SR DC protection (for supply) HFB+13V Non-rectified output 13V-winding LOT DC-filament Filament supply voltage HFB-D Horizontal flyback to FDS...
Page 104
SOUND-ENABLE Sound Enable SC2FH_IFH Sandcastle 1fH/2fH SOUND-SELECT Sound signal Selection SC2-G-IN SCART2 green in SPDIF Sony Philips Digital Interface Format SC2-R-IN C-IN Red in SCART2 or chrominance in SPDIF_IN1 SPDIF In 1 Scavem Scan Velocity Modulation SPDIF_IN2 SPDIF In 2...
Page 105
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 105 STANDARD-FM-1 Standard Frequency Modulation 1 V-OUT V-signal to HOP-IC STANDARD-FM-2 Standard Frequency Modulation 2 VOUT_C V-out Centre STANDBY Standby VOUT_L V-out Left STATUS1/2/3 Status signal from Euro-connector 1, 2...
EN 106 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs).
Page 107
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 107 9.7.2 Diagram B3C, T8F24EF (IC7724) INTERNAL BLOCK DIAGRAM Bus formats 8u@32MHz - 8 bits unsigned data at 32 MHz m 8 s @ 3 2 M H z- multiplexed UV 8 bits signed data at 32 MHz y_-07 τ...
Page 108
EN 108 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.7.3 Diagram CB1, UPD64083GF (IC7023) INTERNAL BLOCK DIAGRAM E XTD Y C O 9-0 DY C O Error S elect VC LY DY C O 9-0 detection EXTALTF...
Page 109
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 109 9.7.4 Diagram F1, TDA8601 (IC7803) INTERNAL BLOCK DIAGRAM PIN CONFIGURATION SYMBOL DESCRIPTION supply voltage (8 V) VIDIa1 video input a (channel 1) VIDIb1 video input b (channel 1)
Page 110
EN 110 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.7.5 Diagram F3, M6232OP (IC7403) INTERNAL BLOCK DIAGRAM CS0 CS1 CS2 CHIP-SELECT I C BUS TRANSCEIVER SHIFT REGISTER Output Data Input/Output OUTPUT DATA I/O SETTING INPUT DATA LATCH...
Page 111
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 111 9.7.6 Diagram F5, Z86130 (IC7501) INTERNAL BLOCK DIAGRAM PIN CONFIGURATION E_15000_120.eps 181004 Figure 9-55 Internal Block Diagram and Pin Configuration...
EN 112 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.7.7 Diagram H1, MC1496D (IC7510 and IC7520) EQUIVALENT SCHEMATIC CARRIER (±) INPUT (+) SIGNAL (±) INPUT (+) GAIN ADJUST BIAS 500k 500k 500k V± PIN CONFIGURATION F, N Packages...
Page 113
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV465 EN 113 9.7.8 Diagram H1, TDA9331H (IC7600) INTERNAL BLOCK DIAGRAM 1 × 2 × PIN CONFIGURATION VDOA VDOB EHTIN FLASH FBCSO GND1 TDA933xH DEC VD HOUT DACOUT E_15000_123.eps 181004...
Page 114
EN 114 DPTV465 Circuit Descriptions, List of Abbreviations, and IC Data Sheets Figure 9-57 Internal Block Diagram and Pin Configuration 9.7.9 Diagram S7, TDA7490 (IC7700) INTERNAL BLOCK DIAGRAM R5 52.3K 470pF 470pF The LC filter is optimized for 8Ω (<->LC filter for 4Ω in single-ended) It hos to be changed for other loads L9 30µ...
Need help?
Do you have a question about the DPTV465 and is the answer not in the manual?
Questions and answers