Table of Contents
Advertisement
Service Modes, Error Codes, and Fault Finding
without a Dolby Signaling bit, this indicator will show "OFF"
even though a Dolby transmission is received.
•
SURROUND MODE. Indicates the by the customer
selected surround mode (or automatically chosen mode).
In case the set is a Non-Dolby set, there will be displayed
"0". If it is a Dolby-set then is displayed: "STEREO", "3
STEREO", "HALL", "3DSURROUND", "DOLBY PRO
LOGIC", or "DOLBY DIGITAL". These settings can be
influenced after pressing the "MENU" button and selecting
"SOUND" and SURROUND MODE". It can also have been
selected automatically by signaling bits (internal software).
•
TUNER FREQUENCY. Indicates the frequency the
selected transmitter is tuned to. The tuner frequency can
be changed via the "CURSOR LEFT" and "CURSOR
RIGHT" keys for fine tune after opening the installation
menu and selecting "INSTALL" and "MANUAL INSTALL".
•
FRONT L TRIM. Indicates the difference between main
volume and volume of front left speaker. Change via:
'MENU', 'SETUP', 'SPEAKERS', and 'FRONT LEFT
VOLUME'. The value can vary from '-10' to '+10'
•
FRONT R TRIM. Indicates the difference between main
volume and volume of front right speaker. Change via:
'MENU', 'SETUP', 'SPEAKERS', and 'FRONT RIGHT
VOLUME'. The value can vary from '-10' to '+10'
•
DIGITAL OPTION. Gives the selected digital mode, "100
HZ", "DIGITAL SCAN", "NATURAL MOTION", "DOUBLE
LINES", or "PIXEL PLUS". Change via "MENU",
"PICTURE", "DIGITAL OPTIONS".
•
CENTRE TRIM. Indicates the difference between main
volume and volume of centre speaker. Change via:
"MENU", "SETUP", "SPEAKERS", and "CENTRE
VOLUME" (not available when "Surround Mode" is set to
"STEREO" or "HALL"). The value can vary from "-10" to
"+10"
•
TV SYSTEM. Gives information about the video system of
the selected transmitter.
–
BG: PAL BG signal received.
–
DK: PAL DK signal received.
–
I: PAL I signal received.
–
L/La: SECAM L/La signals received.
–
M: NTSC M signal received with video carrier on 38.9
MHz.
Customer Service Menu 3
•
BALANCE. Indicates the balance settings, between "-50"
and "+50". Change via "MENU", "SOUND", and
"BALANCE". Not applicable for Dolby Pro Logic sets.
•
CENTRE MODE. Indicates if centre mode is set "ON" or
"OFF". When centre mode is on, all TV speakers are used
as one centre speaker. Change Centre mode via "MENU",
"SETUP", "SPEAKERS", and "CENTRE MODE".
•
DNR. Gives the selected DNR setting (Dynamic Noise
Reduction), "OFF", "MINIMUM", "MEDIUM", or
"MAXIMUM". Change via "MENU", "PICTURE", "DNR"
•
NOISE FIGURE. Gives the noise ratio for the selected
transmitter. This value can vary from 0 (good signal) to 127
(average signal) and to 255 (bad signal). For some
software versions, the noise figure will only be valid when
"Active Control" is set to "medium" or "maximum".
•
SOURCE. Indicates which source is used and the video/
audio signal quality of the selected source. (Example:
Tuner, Video/NICAM) Source: "TUNER", "EXT1", "EXT2",
"EXT3", "EXT4", "SIDE", "AV1", "AV2", "AV3" or "AV4".
Video signal quality: "VIDEO", "S-VIDEO", "RGB 1FH",
"YPBPR 1FH 480P", "YPBPR 1FH 576P", "YPBPR 1FH
1080I", "YPBPR 2FH 480P", "YPBPR 2FH 576P", "YPBPR
2FH 1080I", "RGB 2FH 480P", "RGB 2FH 576P" or "RGB
2FH 1080I". Audio signal quality: "STEREO", "SPDIF 1",
"SPDIF 2", or "SPDIF".
•
AUDIO SYSTEM. Gives information about the audio
system of the selected transmitter: "ANALOGUE MONO",
"ANALOGUE STEREO", "PCM 2/0", "DD 1/0", "DD 2/0
LtRt", "DD 2/0 L0R0", "DD 2/1", "DD 2/2", "DD 3/0", "DD 3/
1", "DD 3/2", "DD 1+1", "MPEG 1/0", "MPEG 2/0", "MPEG
DPTV465
2/0 LtRt", "MPEG 2/1", "MPEG 2/2", "MPEG 3/0", "MPEG
3/1", "MPEG 3/2", "MPEG 1+1" or "MPEG 2+2".
•
TUNED BIT. Gives information about the tuning method of
the stored pre-set. If a channel is found via "automatic
installation", you will see the value "Yes". When you
change this (automatically found) frequency via "fine tune"
adjustment (installation menu - manual installation), the
displayed value will change to "No". Therefore, when you
see the value "No" in this line, it is an indication that the
received channel is a non-standard signal (e.g. of a VCR).
•
SURROUND SPEAKERS. Indicates if the surround
speakers are present "YES" or "NO". Change via "MENU",
"SETUP", "SPEAKERS", and "SURROUND SPEAKERS".
•
ON TIMER. Indicates if the "On Timer" is set "ON" or "OFF"
and if the timer is "ON" also displays start time, start day
and program number. Change via "MENU", "TV",
"FEATURES", and "ON TIMER".
•
PRESET LOCK. Indicates if the selected preset has a child
lock: "LOCKED" or "UNLOCKED". Change via "MENU",
"TV", "FEATURES", "CHILD LOCK", and "CUSTOM
LOCK".
Customer Service Menu 4
•
CHILD LOCK. Indicates the last status of the general child
lock: "UNLOCK", "LOCK", or "CUSTOM LOCK". Change
via "MENU", "TV", "FEATURES", "CHILD LOCK", and
"LOCK".
•
AGE LOCK. Indicates the last status of the EPG rating for
child lock: "OFF", "4 YEARS", "6 YEARS", "8 YEARS", "10
YEARS", "12 YEARS", "14 YEARS" or "16 YEARS". This is
only displayed if child lock is set to "CUSTOM LOCK"
•
LOCK AFTER. Indicates at what time the child lock is set:
"OFF" or e.g. "18:45" (lock time). This is only displayed if
child lock is set to "CUSTOM LOCK"
•
CATEGORY LOCK. Indicates the last status of the EPG
theme childlock: "MOVIES", "NEWS", "SHOWS",
"SPORTS", "CHILDREN", "MUSIC", "CULTURE", or
"SERIES". This is only displayed if child lock is set to
"CUSTOM LOCK". It is possible that more than one value
is shown.
•
PROGRAM CATEGORY. Indicates the theme of the
selected transmitter: "MOVIES", "NEWS", "SHOWS",
"SPORTS", "CHILDREN", "MUSIC", "CULTURE", or
"SERIES".
•
TV RATINGS LOCK. Only applicable for US.
Customer Service Menu 5
•
V-CHIP MOVIE STATUS. Only applicable for US.
•
OPTIONS 1. Gives the option codes of option group 1 as
set in SAM (Service Alignment Mode).
•
OPTIONS 2. Gives the option codes of option group 2 as
set in SAM (Service Alignment Mode).
SW Event-log
This item contains 'software event logging' information that can
be delivered to the development centre on special request.
How to exit CSM
Use one of the following methods:
•
Press a key on the remote control transmitter with
exception of the 'CHANNEL', 'VOLUME' and digit (0-9)
keys)
•
Press the 'POWER' button on the remote control
transmitter or on the TV set.
5.
EN 13
Advertisement
Table of Contents
