All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 568 TV Service...
EN 2 DPTV585 AA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: Connection Overview 1.1 Technical Specifications 1.2 Connection Overview Note: The following connector colour abbreviations are used 1.3 Chassis Overview (acc.
Page 3
Technical Specifications, Connections, and Chassis Overview DPTV585 AA EN 3 - D1+ Data channel 18 - +5V - Shield 19 - HPD Hot Plug Detect - D1- Data channel 20 - Ground - D0+ Data channel - Shield Service Connector (ComPair) - D0- Data channel - SDA-S...
EN 4 DPTV585 AA Safety Instructions, Warnings, and Notes 2. Safety Instructions, Warnings, and Notes Index of this chapter: • The maintenance inspection includes the following actions: 2.1 Safety Instructions 1. Perform the 'general repair instruction' noted above. 2.2 Maintenance Instructions 2.
Figure 2-2 Dolby PL symbol 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
EN 6 DPTV585 AA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Disassembly Procedures 4.1 Disassembly Procedures 4.2 Service Position All numbers, found in the following text, refer to the drawing 4.3 Picture Tube Replacement below and apply to both the 43” and 55” models. 4.4 Set Re-assembly Note: Notes:...
Page 7
Mechanical Instructions DPTV585 AA EN 7 4.1.6 Side Jack Panel Removal 4.1.15 Complete Optical Assembly or Individual CRT Assembly Removal 1. Remove the Left Side Back Cover (see procedure above excluding the Module Bracket removal). 1. Remove the Plastic Light Barrier. 2.
Page 8
EN 8 DPTV585 AA Mechanical Instructions 3. Remove the barrier board and the shield cover from around 13. Make all necessary repairs. the lens assemblies (1/4" screws). 4. Carefully remove the CRT Socket Board from the CRT of C. Cleaning the Coupler, C-Element Lens, and CRT the CRT/optical assembly being serviced.
Page 9
Mechanical Instructions DPTV585 AA EN 9 4. Start the CRT mounting ear screws but do not tighten them. 5. Tighten the CRT mounting ear screws in a star pattern (like tightening lug nuts on the wheel of a car). Make sure the CRT does not shift position from the outline defined in step Caution: do not over tighten the CRT ear screws (the CRT mounting ear screws are not used on some assemblies).
Customer Service Mode (CSM) is used for communication • Access to normal user menu: Pressing the "MENU" button between a Philips Customer Care Centre (P3C) and a on the remote control switches between the SDM and the customer. normal user menus (with the SDM mode still active in the background).
Page 11
Service Modes, Error Codes, and Fault Finding DPTV585 AA EN 11 Clear Errors: Erases the contents of the error buffer. Select the CLEAR ERRORS menu item and press the LEFT or RIGHT cursor key. The contents of the error buffer are cleared. HRS: 0062 SWID: HD5.2US1-1.0 The functionality of the OPTIONS and ALIGNMENTS (TUNER, WHITE TONE, GEOMETRY, SOUND, and SMART SETTING)
Page 12
EN 12 DPTV585 AA Service Modes, Error Codes, and Fault Finding – SWID: Software identification of the main micro 'Contrast' value. The new value(s) are automatically stored controller (2US1-1.00) (in 'personal' pre-set) for all TV channels. – US1 is 2 letter and 1 digit combination to indicate the 2.
Page 13
5.4.1 Introduction 5.4.3 How To Connect ComPair (Computer Aided Repair) is a service tool for Philips This is described in the chassis fault finding database in Consumer Electronics products. ComPair is a further ComPair . development on the European DST (service remote control), which allows faster and more accurate diagnostics.
Page 14
EN 14 DPTV585 AA Service Modes, Error Codes, and Fault Finding Error Codes Table 5-1 Error Code Table Error number Explanation 5.5.1 Introduction No error The error code buffer contains all errors detected since the last FBX 3V3 protection time the buffer was erased. The buffer is written from left to No Horizontal Flyback protection right.
Page 15
Service Modes, Error Codes, and Fault Finding DPTV585 AA EN 15 Table 5-2 Error Code Table GDE Error Error Name Description Vertical Output Failure This error indicates the Vertical Deflection pulse received at pin 9 on the TDA933x is not correct. This can be caused by a failure in the HOP board or the Scan Board.
EN 16 DPTV585 AA Service Modes, Error Codes, and Fault Finding The ”Blinking LED” Procedure Checking the Screen voltage from the Focus G2 block will indicate whether the High voltage circuit is working or not. Horizontal and Vertical drive from the HOP panel must be 5.6.1 Introduction present for the High voltage to be present.
Circuit Diagrams and PWB Layouts DPTV585 AA Mapping SSM C1-C8 Part 3 Personal Notes: SMALL SIGNAL MODULE (AP) E_06532_012.eps E_15000_022.eps 3135 033 3345.7 191004 131004...
Page 41
Circuit Diagrams and PWB Layouts DPTV585 AA Layout SSM (Top Side) F_15120_013.eps 3139 123 6060.1 020805...
Page 42
Circuit Diagrams and PWB Layouts DPTV585 AA Layout SSM (Bottom Side) F_15120_014.eps 3139 123 6060.1 020805...
Circuit Diagrams and PWB Layouts DPTV585 AA CRT Panel: Red D(R)1 D(R)1 RED CRT PANEL 1202 EH-S To HOP Panel 200mV / div AC 100mV / div AC 100mV / div AC 100mV / div AC 1V / div AC 1V / div AC 1V / div AC To LSP Panel...
Circuit Diagrams and PWB Layouts DPTV585 AA CRT Panel: Green D(G)1 D(G)1 GREEN CRT PANEL 1202 EH-S To HOP Panel 1720 To LSP Panel 1202 200mV / div AC 100mV / div AC 100mV / div AC 1V / div AC 1V / div AC 1V / div AC 1V / div AC...
Circuit Diagrams and PWB Layouts DPTV585 AA CRT Panel: Blue D(B)1 D(B)1 BLUE CRT PANEL 1202 EH-S 200mV / div AC 100mV / div AC 100mV / div AC 1V / div AC 1V / div AC 1V / div AC To HOP Panel 1720 To LSP Panel 1202 10µs / div...
Circuit Diagrams and PWB Layouts DPTV585 AA Large Signal Panel LARGE SIGNAL PANEL VFOC EHT EHT 5904 I910 5902 I912 1504 I914 F900 3902 +130VHV DRIVER & CONTROL TRANSFORMER VAUX ON / ABL RTN VAUX TEST OFF GND DYN FOCUS NC NC 1901 I915...
Circuit Diagrams and PWB Layouts DPTV585 AA LSP: Diversity Tables Personal Notes: DIVERSITY TABLES SHEET 1 USA BASIC 4:3 USA BASIC 16:9 USA CORE 4:3 USA CORE 16:9 Ref Des 313503710981 313503710991 313503711001 313503711011 NOT_USED 0213 NOT USED NOT USED NOT USED NOT USED 313501104201...
Page 52
Circuit Diagrams and PWB Layouts DPTV585 AA Layout Large Signal Panel (Top Side) F_15120_020.eps 3135 033 3341.1 020805...
Page 53
Circuit Diagrams and PWB Layouts DPTV585 AA Layout Large Signal Panel (Bottom Side) F_15120_021.eps 3135 033 3341.1 020805...
Page 54
Circuit Diagrams and PWB Layouts DPTV585 AA Side Jack Panel 1001-1 B2 1001-2 C2 1001-3 D2 Side Jack Panel 1002 A2 1007 E6 1335 B7 Ref Des 3135_037_05461 3135_037_10581 3135_037_11961 3135_037_12131 3135_037_12321 RESERVED 1002 242202604926 242202604926 242202604926 242202604926 NOT USED NOT USED 1337 E2 YKF51-5347...
Circuit Diagrams and PWB Layouts DPTV585 AA Mapping Side Jack Panel G1 Personal Notes: A10PTV SIDE JACK PANEL E_06532_012.eps E_15000_033.eps 3135 033 3217.4 131004 191004...
Page 56
Circuit Diagrams and PWB Layouts DPTV585 AA Layout Side Jack Panel (Top Side) Layout Side Jack Panel (Bottom Side) 2000 A1 2001 B1 1001 B1 2002 B1 1002 A1 2005 B1 1007 C1 2006 B1 1335 B1 2008 C1 1337 C1 2009 C1 1344 C1 3000 B1...
Circuit Diagrams and PWB Layouts DPTV585 AA Mapping ACS Module H1-H3 ACS MODULE: MAPPING AUTO CONVERGENCE 3135 013 32338 F_15120_025.eps 3135 013 3233.8 020805...
Page 61
Circuit Diagrams and PWB Layouts DPTV585 AA Layout ACS Panel (Top Side) F_15120_026.eps 3135 013 3233.8 020805...
Page 62
Circuit Diagrams and PWB Layouts DPTV585 AA Layout ACS Panel (Bottom Side) F_15120_027.eps 3135 013 3233.8 020805...
Page 63
Circuit Diagrams and PWB Layouts DPTV585 AA HOP Panel HOP PANEL To 1210 of To 1210 of To 1210 of CRT Panel CRT Panel CRT Panel (BLUE) (GREEN) (RED) 1720 EH-B 1710 EH-B 1700 EH-B +12V +12V B-BIAS 7800 TDA8444T/N4 G-BIAS 3421 R-BIAS...
Circuit Diagrams and PWB Layouts DPTV585 AA Diversity HOP Panel J1 and J2 Personal Notes: HDR2K4 HOP 28KHZ AP AUG RESERVED N3 HOP DB15 N3 HOP W/O DB15 N3 HOP DB15 N3 HOP W/O DB15 RESERVED Ref Des 3135_037_12781_01 3135_037_12791_01 RESERVED Ref Des 3135_037_12781_01...
Circuit Diagrams and PWB Layouts DPTV585 AA Mapping HOP Panel Part 2 Personal Notes: HDR2K4 HOP 28KHZ AP AUG E_06532_012.eps 131004 E_15000_046.eps 3135 033 3429.2 191004...
Page 68
Circuit Diagrams and PWB Layouts DPTV585 AA Layout HOP Panel (Top Side) F_15120_030.eps 3139 123 6064.1 020805...
Page 69
Circuit Diagrams and PWB Layouts DPTV585 AA Layout HOP Panel (Bottom Side) F_15120_031.eps 3139 123 6064.1 020805...
Alignments DPTV585 AA EN 75 8. Alignments Index of this chapter: 5. Repeat steps two through four to adjust the focus of the two 8.1 General Alignment Conditions remaining CRTs. 8.2 Hardware alignments 8.3 Software Alignments Note: Before beginning the following adjustment procedures 8.4 Convergence and Geometry Adjustments set the customer picture, sharpness, brightness, and tint 8.5 Option Settings...
Page 76
EN 76 DPTV585 AA Alignments 1. During the IF AFC-parameter adjustment, one can see • LUM. DELAY PAL BG: Apply a PAL BG colour bar / grey OSD feedback on the screen. scale pattern as a test signal. Adjust this parameter until 2.
Page 77
Alignments DPTV585 AA EN 77 3. Grey Scale (White Tone). After entering the default values, the E-W WIDTH, VERTICAL SLOPE, and VERTICAL AMP should be the only settings If the SSM (Small Signal Module has been changed: requiring further adjustment. 1.
Page 78
EN 78 DPTV585 AA Alignments CURSOR RIGHT MENU CURSOR KEYS TO ADJUST CURSOR KEYS TO NAVIGATE MENU TO CHANGE MENU TO ADJUST STEP SIZE I+ TO RETURN I+ TO RETURN GREEN RED TO GREEN BLUE TO GREEN GREEN TO RED BLUE TO RED SP RED SP BLUE...
Page 79
Alignments DPTV585 AA EN 79 8.4.7 Touch Up Convergence When the GREEN geometry is complete, STORE the data. Remove the template from the screen. Select RED TO GREEN in the selection menu. Using the same method that was used When making minor Convergence corrections, move the to adjust the Green Grid to the Template, adjust the Red Grid Cursor to the location to be adjusted then press the MENU onto the Green Grid.
Page 80
EN 80 DPTV585 AA Alignments – WARM DRIVE BLUE: “-8” 8.5.4 Option Codes 15.Press the MENU button to return to the SAM menu. Exit the Service mode by turning the set ”off”. Enter the Service Alignment Mode (SAM) by pressing the following key sequence on the remote control transmitter: 0-6-2-5-9-6-[i+].
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 81 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets Index of this chapter: Power Supplies 9.1 Introduction 9.2 Power Supplies The Rectifiers and Standby Supplies are located on the AC 9.3 Video Input Panel.
Page 82
EN 82 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.2.2 AC Input Board F_15120_040.eps 090805 Figure 9-2 AC input board The AC Input circuit is located on the AC Input panel. AC power and 6402. Bridge 6500 provides the RAW B+ to the Main is connected to the AC Input panel via connector 1505.
Page 83
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 83 bridge rectifier is fed to the base of 7512, keeping it turned On. Under voltage Detection This keeps Transistor 7513 turned Off. If the DC voltage drops to approximately 75 volts, Transistor 7512 will turn Off, Transistor 7513 will turn On, putting the anode of Zener 6516 to ground, clamping the voltage on Pin 6 at 5 volts.
Page 84
EN 84 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets sets the reference voltage for comparator "B", which is Power Fail Shutdown compared with the voltage on the source of 7301. This voltage is developed when 7301 turns "on", causing current to flow through resistors 3308 and 3309.
Page 85
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 85 doubler circuit on the SSB, called the Feature Box, changes the 9.3.2 SSM composite Inputs interlaced 625 or 525 signal to a Progressive Scan 480p, 576p, 100Hz, or 120 Hz signal. This YUV signal is buffered and fed to the SSM where it is buffered before being fed to the HOP (High end Output Processor) panel.
Page 86
EN 86 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.3.4 SSB Video Switching 9.3.5 SAW Filter Switching E_15000_077.eps 181004 Figure 9-12 SAW filter switching circuit The HDR2K3 AP set has a Multi-System tuning system. Since NTSC uses a 6 MHz bandwidth and PAL/SECAM uses an 8 MHz bandwidth, it is necessary to have separate SAW filters.
Page 87
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 87 9.3.7 Sound Trap Switching 9.3.8 1fH Component Buffer Amplifiers E_15000_079.eps 181004 Figure 9-14 Sound trap switching circuit Composite video is output on pin 10 of 7323 and buffered by transistor 7411.
Page 88
EN 88 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets The circuit located on the SSB labelled the Feature Box 9.3.10 Eagle performs the digitising, line doubling, and picture resizing. The main functions are performed by 7611, PICNIC (PICture improvement Network IC), and 7718, FALCONIC (Field And 7722 7731 7728...
Page 89
1080i. The A/D, U201 shares a 16bit bus with the HDMI 720p progressive scan or 480i, 1080i interlaced. receiver. Only the Philips version has the HDMI input. The Customer selected signal is fed to U201, the ATSC processor. IC7210 selects between the output of the ATSC panel and the The ATSC processor enhances and rescales the signals from YUV signal from the SSM.
Page 90
EN 90 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets E_15000_088.eps 181004 Figure 9-21 HOP signal processing 9.3.15 HOP Sharpness Control signal, it is amplified by 7412 and buffered by 7413. If the input was a U signal, it is buffered by 7414. 9.3.16 HOP Tint Control E_15000_089.eps 181004...
Page 91
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 91 9.3.17 HOP RGB Amplifiers 9.3.19 CRT Panel E_15000_093.eps 181004 Figure 9-26 RGB amplifiers on CRT panel E_15000_091.eps The Red, Green, and Blue signals from the HOP panel are fed 181004 to their respective CRT panel.
Page 92
EN 92 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.3.21 Line Output E_15000_095.eps 181004 Figure 9-28 Line output circuit Horizontal drive from the HOP panel is fed to 7807 on the Large Signal panel. Transistor 7807 drives the Horizontal Output Transistor 7801, which drives the Yokes and the Horizontal Output Transformer 5801.
Page 93
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 93 9.3.23 High Voltage Circuit E_15000_097.eps 181004 Figure 9-30 High voltage circuit The High Voltage module is an integrated High Voltage supply produce a 375 Volt source for the Dynamic Focus drive. The with its own switching power supply.
Page 94
EN 94 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets transistor turned "off". In the same manner, the Negative Convergence Horizontal Output Horizontal pulses keep the base of 7810 at a negative voltage to keep it turned "off". The Protect line is normally Low, keeping 7809 turned "off".
Page 95
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 95 up circuit senses a negative 10 to 12 volt drive to the Vertical Left and Right audio is output to a Headphone Amplifier located Convergence yokes, the VccNSW-V supply will switch from - on the SSM.
Page 96
EN 96 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets The Audio Amplifier is located on the SSM. The output power If the Power Fail line should go "high", 7710 will turn "on", for the Audio Amplifier is 10 Watts per channel for the Basic causing the Standby-Mute line to go Low.
Page 97
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 97 SENSOR +3.3V BOARD 1201 1014 1020 KEYBOARD 23-37 7010 7100 STBY 7001 CONTROL 7006 ON/OFF 7007 7012 PROGRAM DRAM FLASH FLASH-RAM STANDBY SDA-B CONV LIGHT SENSOR PROC SCL-B 45-66 TO HOP...
Page 98
EN 98 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.5.4 I2C interconnect 7022 7002 CONV 1401 1043 1000 PROC 7021 7020 SDA-B 7100 MICRO 7024 7023 SCL-B SDA-F SCL-F 7000 3655 3709 3710 3376 3656 3377 7001 1000 7713...
Page 99
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 99 List of Abbreviations DAC-HOP Digital analogue converter HOP IC DC_PROT/ AUDIO_SR DC protection (for supply) 16:9-ARFRONT 16:9 aspect ratio input from side jack DC-filament Filament supply voltage panel DC-PROT DC protection...
Page 100
EN 100 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets HEATER Heater (Filament) NTSC National Television Standard Horizontal flyback Committee. Colour system mainly HFB+13V Non-rectified output 13V-winding LOT used in North America and Japan. HFB-D Horizontal flyback to FDS Colour carrier NTSC M/N= 3.579545 High-end Input Processor MHz, NTSC 4.43= 4.433619 MHz (this...
Page 101
VGA Green SOUND-ENABLE Sound Enable VGA-R VGA Red SOUND-SELECT Sound signal Selection VL_L Variable level Left SPDIF Sony Philips Digital Interface Format VL_R Variable level Right SPDIF_IN1 SPDIF In 1 VL_SL Variable level - Surround Left SPDIF_IN2 SPDIF In 2 VL_SR...
Page 102
EN 102 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets V-OUT V-signal to HOP-IC VOUT_C V-out Centre VOUT_L V-out Left VOUT_R V-out Right VOUT_SL V-out Surround Left VOUT_SR V-out Surround Right VOUT-SW V-out Subwoofer VREG Opto-coupler feedback signal VS-DS Main, Vertical sync input POPOV (Double Window PIP IC)
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 103 IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs). 9.7.1 Diagram B7, SAA5667HL (IC7001) Internal Block Diagram...
EN 104 DPTV585 AA Circuit Descriptions, List of Abbreviations, and IC Data Sheets 9.7.2 Diagram E1, MC44603A (IC7302) PIN CONNECTIONS V CC R ref R Frequency Standby Voltage Feedback Output Input Error Amp Output Foldback Input R Power Standby Overvoltage Soft–Start/D max / Protection (OVP) Voltage Mode...
Page 105
Circuit Descriptions, List of Abbreviations, and IC Data Sheets DPTV585 AA EN 105 9.7.3 Diagram H1, STV2050 (IC7002) i l a e i l e i l ² c i t ² I e t l C ² l l i l a t e t l l e l...
Need help?
Do you have a question about the Colour Television and is the answer not in the manual?
Questions and answers