Roc Hobby 1100MM MXS 3D Operating Manual
  1. Manuals
  2. Brands
  3. Roc Hobby Manuals
  4. Toy
  5. 1100MM MXS 3D
  6. Operating manual

Roc Hobby 1100MM MXS 3D Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

1100MM MXS 3D
1100
1080
1 00g 38 .8
1
30.8
35.7
0.081
43.3
42.5
478.7
4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1100MM MXS 3D and is the answer not in the manual?

Questions and answers

Related Manuals for Roc Hobby 1100MM MXS 3D

Summary of Contents for Roc Hobby 1100MM MXS 3D

  • Page 1 1100MM MXS 3D 43.3 1100 1080 42.5 1 00g 38 .8 30.8 478.7 35.7 0.081...
  • Page 2 WARNING WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product. personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires in injury or damage to the product or other property.

  • Page 3: Table Of Contents

    ESC instrouction............................15 Introductions Introducing the all new 1100mm MXS 3D aerobatic plane from FMS Models. Designed for the Intermediate to advanced 3D pilot & built specifically for 3D Flight, the MSX is sure to please even the most capable of 3D pilots.

  • Page 4: Contents Of Kit

    Contents of Kit Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and labels. If any parts are missing or defective, please indentify the name or part number (refer to the spare parts list near the end of the manual) then contact your local shop or email us: support@fmsmodel.com A: Front Landing Gear Set G: Horizontal stabilizer mounting screws (PA2.3*10mm)
  • Page 5 PA2.3*10mm fig3 fig4 fig6 fig5 4. Install the rudder servo arm and linkage as shown in Figures 7 and 8. fig7 fig8 5. Attach the main landing gear using 3 PM 3.0 X 10mm screwsas shown in Figure 9. 6. Find the Y-harness and connect it to both aileron servos.Connect the Y-harness to the receiver, then place the receiver into the fuselage as shown in Figure 10 .

  • Page 6: Install The Battery And Radio Installation

    Assemble the main wing as shown in Figure 11. Use four screws to lock the wing as shown in Figure 12. fig11 fig12 8.Glue on the Vortex Generator on the wing tip using the applied glue (fig13). fig13 Install the battery and Radio installation 1.

  • Page 7: Get Your Model Ready To Fly

    Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or position, the motor will not start until the throttle stick is moved to the low throttle or off position.

  • Page 8: Check The Control Throws

    Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): Tips: At first flight, fly the model in low rate. The first time you use high rates, be sure to fly at low to medium speeds.

  • Page 9: Linkage Rod Installation

    Linkage rod Installation Press the socket-style linkage connector over the corresponding ball end on the control horn. Control Horn and Servo Arm Settings The table shows the factory settings for the control horns and servo arms. Fly the aircraft at the factory settings before making changes.

  • Page 10: Install The Propeller And Spinner

    Install the propeller and spinner Assemble the spinner and propeller as shown below. Check the C.G. (Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference.

  • Page 11: Before Flying The Model

    Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best.

  • Page 12: Flying Course

    Flying course Take off While applying power, slowly steer to keep the model straight. the model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. MXS 3D will climb out at a nice angle of attack (AOA).

  • Page 13: Troubleshooting

    Troubleshooting...

  • Page 14: Spare Parts List Content

    Spare parts list content ROCKH101 Fuselage ROCKH102 Main Wing Set ROCKH103 Horizontal Stabilizer ROCKH104 Cowl ROCKH105 Battery Hatch ROCKH106 Main Landing Gear Set ROCKH107 Rear Landing Gear Set ROCKH108 Spinner Set ROCKH109 Linkage Rod ROCKH110 Vortex Generator ROCKH111 Decal Sheet ROCKH112 Pipe Set FMSPROP047 Propeller...

  • Page 15: Esc Instrouction

    ESC instruction...

Table of Contents