1. Manuals
  2. Brands
  3. Radio control model Manuals
  4. Toy
  5. VQA038
  6. Instruction manual

Radio control model VQA038 Instruction Manual

Magic pylon racing
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Wingspan:
Radio
Engine
WARNING!
This radio control model is not a toy. If modified or flow carelessly it could go out of control
and cause serious bodily injury or property damage.
Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas with no debris or obstacles.
Radio control model

INSTRUCTION MANUAL

MAGIC
PYLON RACING
:
:
1148mm (45.2")
4 channels
.25 -.32 two-stroke
VQA038
VQA039

Advertisement

Table of Contents
loading

Related Manuals for Radio control model VQA038

Summary of Contents for Radio control model VQA038

  • Page 1: Instruction Manual

    .25 -.32 two-stroke WARNING! This radio control model is not a toy. If modified or flow carelessly it could go out of control and cause serious bodily injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
  • Page 2 REQUIRED FOR OPERATION (Purchase separately) 9 x 6 for .25 - 2 cycle engine 9.5x6 for .32 - 2 cycle engine Silicone tube Minimum 4 channel radio Extension for aileron for airplane servo. .Motor control x1 .Aileron x1 .25 ~ .32 - 2 cycle .Elevator x1 .Rudder x1 GLUE (Purchase separately)

  • Page 3: Aileron Servo

    TOP VIEW 1- Joining the wing Cut away only the covering. 1- Using a pencil, mark the center of the brace 2- Trial fit the wing joiner, into one of the wing panels. It should insert smoothly up to the center line Center line marked.

  • Page 4: Aileron Linkage

    1- Install one clevis onto each of the aileron torque rod horn. With the aileron 4-Aileron Linkage and aileron servo in the neutral position, mark the position where it each of the linkages will attach to the servo arm. 2- Insert the aileron linkages into the servo arm accordingly. Clevis ..2 Ensure that the servo is centered.

  • Page 5: Vertical Stabilizer

    Control horn 7- Vertical stabilizer ...1 ! Make sure to glue securely, If not properly glued, a failure in flight may occur. 2x12mm screw ...2 Cut away only the covering B’ (30 min) A’ (5 min.) A=A’ B=B’ * WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement.

  • Page 6: Fuel Tank

    10- Fuel tank To muffler Filler tube To engine Blow Carefully install the fuel tank to ensure that they will not shift during flight (secure the fuel tank in place using foam padding). Water Checking for leaks - block the vents and blow into the feed - if in doubt submersing the tank in a blow of water will show up any problems 11- Engine 1- Position the engine on the engine mounts.
  • Page 7 Elevator pushrod 12-Battery - receiver - servo 3mm set Screw Linkage stopper ....3 Connector Elevator pushrod x2 ...1 2 mm FUSELAGE - BOTTOM VIEW Throttle servo ELEVATOR SERVO Rudder servo 3mm set Screw Throttle pushrod D=3/64”(1.2mm) Rudder pushrod D=5/64”(2mm) 2 mm Throttle push rod 3 holes connector Elevator servo...

  • Page 8: Control Surface

    15- Control surface WARNING ! Securely install the receiver and power pack, ensuring they will not come loose or rattle during flight. 2-11/16” Never fly before checking the Cg’s required position. 68mm Wing section Pre-flight check Check that each clevis is securely snapped into position. Check that all servo horn screws are tight.

This manual is also suitable for:

Vqa039

Table of Contents