Ics6011 Quick Reference - Epson E0C6011 Development Manual

5.3 ICS6011 Quick Reference

Starting command and input/output files
Execution file:
Starting command:
Input file:
Output file:
Display example
*** E0C6011 ICE CONTROL SOFTWARE. --- Ver 3.01 ***
EEEEEEEEEE PPPPPPPP
EEEEEEEEEE PPPPPPPPPP
EEE PPP PPP
EEE PPP PPP
EEEEEEEEEE PPPPPPPPPP
EEEEEEEEEE PPPPPPPP
EEE PPP
EEE PPP
EEEEEEEEEE PPP
EEEEEEEEEE PPP
(C) COPYRIGHT 1991 SEIKO EPSON CORP.
* ICE POWER ON RESET *
* DIAGNOSTIC TEST OK *
#
Error messages
Error message
* COMMUNICATION ERROR
OR ICE NOT READY *
* TARGET DOWN (1) *
* TARGET DOWN (2) *
* UNDEFINED PROGRAM
CODE EXIST *
* COMMAND ERROR *
(No response after power on)
E0C6011 DEVELOPMENT TOOL MANUAL
ICS6011.BAT (ICS6011J.EXE)
ICS6011B.BAT (ICS6011W.EXE)
ICS6011 (ICS6011J)
ICS6011B (ICS6011W)
C011XXXL.HEX (Object file, low-order)
C011XXXH.HEX (Object file, high-order)
C011XXXD.HEX (Data RAM file)
C011XXXC.HEX (Control file)
C011XXXL.HEX (Object file, low-order)
C011XXXH.HEX (Object file, high-order)
C011XXXD.HEX (Data RAM file)
C011XXXC.HEX (Control file)
SSSSSSS OOOOOOOO
SSS SSSS OOO OOO
SSS SSS OOO OOO
SSS OOO OOO
SSSSSS OOO OOO
SSSS OOO OOO
SSS OOO OOO
SSS SSS OOO OOO
SSSS SSS OOO OOO
SSSSSSS OOOOOOOO
Meaning
ICE62R (ICE6200) is disconnected
or power is OFF.
Evaluation board is disconnected.
(Check at power ON)
Evaluation board is disconnected.
(Check at command execution)
Undefined code is detected in the
program loaded from ROM or FD.
A miss occurs by command input.
The ICE-to-HOST cable is
disconnected on the host side.
5 ICE CONTROL SOFTWARE ICS6011
. . . for MS-DOS
. . . for PC-DOS
. . . for MS-DOS
. . . for PC-DOS
Start-up message
When ICS6011 is started, the start-up
NNN NNN
NNNN NNN
message is displayed, and a self-test is
NNNNN NNN
NNNNNN NNN automatically performed. ICS6011
NNN NNN NNN
commands are awaited when the program
NNN NNNNNN
NNN NNNNN
is properly loaded and the # mark is
NNN NNNN
NNN NNN
displayed.
NNN NN
Debugging can be done by entering
command after the # mark.
The ICS6011 program is terminated by
entering the Q (Quit) command.
Note Confirm that the cables con-
Switch OFF the host power supply, connect cable, and
reapply power. Or switch ON power to ICE62R (ICE6200).
Switch OFF power to ICE, and connect the evaluation
board. Then, apply power to ICE62R (ICE6200).
Switch OFF power to ICE, and connect the evaluation
board. Then, apply power to ICE62R (ICE6200).
Convert ROM and FD data with the cross assembler,
then restart the ICE62R (ICE6200).
Reenter the proper command.
Switch OFF the host power supply, connect cable,
and reapply power.
EPSON
indicates the Return key.
nected properly, then operate
the ICS6011.
Recover procedure
29