Craftsman 315.218060 Operator's Manual page 42

CRAFTSMAN 10 in. TABLE SAW – MODEL NO. 315.218060
The model number will be found on a plate attached to the motor housing. Always mention the model
number in all correspondence regarding your Table Saw or when ordering repair parts.
Key Part
No. Number Description
1 0134011803
2 0134010211
3 0134010308
4 0134010103-126 Extension Table ......................... 1
5 0101140903 * Hex Key (M5 x 75 mm) ............. 1
6 410371002 * Screw (M6 x 15 mm Hex Hd.) ... 4
7 0134010212
8 410561014 * Screw (M4 x 5 mm) ................... 1
9 0134011802
10 410561004 * Screw (M4 x 12 mm. Pan Hd.) . 2
11 0134010242
12 0134010219
13 0134010307-129 Throat Plate ............................... 1
14 410101005 * Screw (M5 x 15 mm Flat Hd.) ... 2
15 0121011301
16 0134010102-126 Main Table ................................. 1
17 0134010213
18 0131020220
19 0131010814 * Screw (10-24 x 25 mm Hex Hd.) 4
20 0131010229
21 410171706
22 0134010911
23 0134010210
24 410171721 * Screw (8-32 x 3/8 in.) ................ 2
25 410011013 * Screw (M6 x 40 mm Hex Hd.) ... 1
26 0134010206
27 411061001 * Lock Nut (M6) ........................... 3
28 0134010332
29 0134010902
30 0134010229
31 410031002 * Carriage Bolt (M6 x 40 mm) ...... 1
32 0134010306
33 410251017 * Screw/Washer (M6 x 12 mm) .... 2
34 0134010916
35 0134010903
36 410551701
37 0134010209
38 0134010223
39 410351003 * Screw/Washer
40 0121010214
41 9134015330203 Warning Label ........................... 1
42 0134010237-130 Cord Wrap ................................. 1
43 410251020 * Screw (M6 x 15 mm Pan Hd.) ... 4
44 0134010322-58 Outfeed Support ....................... 1
45 410201005 * Screw (M4 x 12 mm Flat Hd.) ... 4
Rear Rail ................................... 1
End Cap, Rear Rail ................... 2
Rail Holder Nut .......................... 4
End Cap, Right Front Rail ......... 1
Front Rail .................................. 1
Stopper, Front Rail .................... 1
Indicator, Extended Table ......... 1
Pad, Throat Plate ...................... 2
Slider ......................................... 5
Table Tilt Handle ....................... 1
Carry Handle ............................. 1
Screw (10-24 x 1/2 in. Tapping) 4
Slide Bolt ................................... 1
Guide ........................................ 1
Locking Block ........................... 2
Adjusting Plate .......................... 1
Linkage, Short ........................... 1
Table Extension Lever ............... 1
Bracket ...................................... 1
Guide Rod ................................. 2
Linkage, Long ........................... 1
Screw/Washer (1/4-20 x 1/2 in.) ... 2
Handle, Left .............................. 1
Holder, Rear Rail ....................... 3
(M6 x 25 mm Hex Hd.) .............. 6
Extension Bracket ..................... 2
* Standard Hardware Item – May Be Purchased Locally
PARTS LIST
Key Part
Qty. No. Number
46 0134010314
47 411071707
48 0134011804
49 410192001
50 410109008
51 0134010220
52 0134010315
53 410371003
54 0134010215
55 410031014
56 410341006
57 411171003
58 0134010319
59 0134010321
60 411011707
61 410291006
62 0134015001
63 0134010317
64 0121010901
65 0134010503
66 410109019
67 412011701
68 0101010908
69 0134010305
70 410291004
71 0134010236
72 412011117
73 0134010339
74 410134005
75 0181010246
76 412042002
77 0134010320
78 410499007
79 9134015330107 Name Plate .............................. 1
80 0134011301
81 0134010230
82 0134010912
83 0134010316
84 410138743
85 0134010224
86 0101010907
87 0000120817
88 0134010228
89 410331010
90 0134010233
42
Description
Bar, Sliding Miter Table ............. 2
* Lock Nut (1/4-20) ...................... 1
Sliding Bar ................................ 2
* Screw (M4 x 10 mm) ................. 2
* Screw (M5 x 12 mm Pan Hd.) ... 4
Slider ......................................... 2
Bracket ...................................... 2
* Screw w/Washer (M6 x 12 mm) 4
Slider ......................................... 2
* Carriage Bolt (M8 x 15 mm) ...... 1
* Screw w/Washer (M6 x 12 mm) 2
Wing Nut (M8) ........................... 1
Bracket, Riving Knife ................ 1
Pivot Bracket ............................ 1
* Hex Nut (1/4-20) ....................... 1
* Screw w/Washer (M8 x 10 mm) 1
Dust Bag ................................... 1
Indicator Bracket ...................... 1
Eccentric Shaft ......................... 1
Plate .......................................... 1
* Screw (M6 x 20 mm Flat Hd.) ... 1
Washer (1/4 x 16 x 1T) .............. 2
Nut, Special .............................. 1
Support Bracket ........................ 1
* Screw/Washer (M6 x 10 mm) .... 2
Locking Ring ............................. 1
Washer (M10 x 23 x 2T) ............ 1
Cam .......................................... 2
* Screw (M4 x 5 mm Pan Hd.) ..... 2
Adaptor ..................................... 1
Washer (D4) ............................... 2
Support Plate, Front Cabinet .... 1
* Screw (M5 x 8 mm Truss Hd.) ... 2
Rubber Pad ............................... 1
Bevel Locking Lever ................. 1
* Screw (SS41) ............................ 1
Shim .......................................... 1
Screw (8-32 x 1 in. Pan Hd.) ..... 1
Cam, Bevel Locking Lever ........ 1
Compression Spring ................. 1
* Screw (8-16 x 19.05 mm) .......... 2
Gear Rack ................................. 1
* Screw w/Washer
(M5 x 8 mm Pan Hd.) ................ 2
Indicator, Bevel Angle ............... 1
Qty.