Table of Contents
Advertisement
HCD-EC98P
COLD RESET
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
on.
2. Press three buttons of [
], [FUNCTION] and at last [
x
multaneously.
3. When "RESET" appears, the set enters standby status.
PANEL TEST MODE
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the [
on.
2. Press three buttons of [DISPLAY], [
multaneously.
3. When the panel test mode is activated, LEDs and segments of
the liquid crystal display are all turned on.
Version Check
Procedure:
1. In the panel test mode (all LEDs and segments of the liquid
crystal display are turned on), press the [FUNCTION] button.
2. On the liquid crystal display, date and version are displayed
"xxxxxxxx". For example, "1114V102".
3. From this status, press the [
model name are displayed. For example, "CE2" and "ESLO–".
4. To release from this mode, press three buttons of [DISPLAY],
[
], and [FUNCTION] simultaneously.
x
Key Test Mode
Procedure:
1. In the panel test mode (all LEDs and segments of the liquid
crystal display are turned on), press the [DISPLAY] button.
2. The message "KEY0 0 0"displayed. Whenever any buttons
are pressed and the [VOLUME] dial is turned, the value is
changed.
3. To release from this mode, press three buttons of [DISPLAY],
[
], and [FUNCTION] simultaneously.
x
CD REPEAT 5 LIMIT CANCEL MODE
Number of repeats for CD playback is 5 times when the repeat
mode is "REPEAT". This mode enables CD to repeat playback for
limitless times.
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [DISPLAY], [
ING] simultaneously.
4. It enters the CD repeat 5 limit cancel mode and displays "NO
LIMIT"
5. To release this mode, press the [
CD SHIP MODE
This mode can run the CD sled motor optionally. Use this mode,
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Confi rm there is no disc in all trays.
3. Press the [FUNCTION] button to select CD function.
4. Press two buttons of [N] and [
5. Set to the CD ship mode. (chucking on)
6. After blink "STANDBY", "LOCK" is displayed, disconnect
the AC plug.
18
SECTION 4
TEST MODE
] button to turn the power
?/1
?/1
] button to turn the power
?/1
], and [FUNCTION] si-
x
] button, and the destination and
X
], and [l m – TUN-
x
] button to turn the power off.
?/1
] simultaneously.
?/1
CD TRAY LOCK
This mode is for the antitheft of CD disc in shop. (not for trans-
port)
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press the [FUNCTION] button to select CD function.
3. Insert a disc.
] si-
4. While pressing the [
seconds.
5. The message "LOCKED" is displayed and the disc tray is
locked. (Even if exiting from this mode, the disc tray is still
locked)
6. If press the [
] button to eject the disc, the message "LOCKED"
Z
is displayed and can not eject the disc.
7. To release this lock, while pressing the [
[
] button for 5 seconds again.
Z
8. The message "UNLOCKED" is displayed and the disc tray is
unlocked.
CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press the [FUNCTION] button to select CD function.
3. Press the [
] button again to turn the power off (standby).
?/1
4. After pressing the [DISPLAY] button, while pressing the [
button, press the [
5. It turns power on and display "CD POWER", then display
"ON" or "OFF".
CHANGE-OVER THE AM TUNING INTERVAL
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press the [TUNER/BAND] button to select TUNER (AM)
function.
3. Press the [
] button again to turn the power off (standby).
?/1
4. After pressing the [DISPLAY] button, while pressing the
[TUNING + M L] button, press the [
5. It turns power on and display "9k STEP" or "10k STEP", and
thus the tuning interval is changed over.
CD SHIP AND COLD RESET
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Confi rm there is no disc in all trays.
3. Press the [FUNCTION] button to select CD function.
4. Press three buttons of [PLAY MODE/TUNING MODE],
[l m – TUNING] and [
5. After blink "STANDBY", "RESET" is displayed, disconnect
the AC plug.
COMMON TEST MODE
Procedure:
1. Press the [
] button to turn the power on.
?/1
2. Press three buttons of [PLAY MODE/TUNING MODE],
[TUNING + M L], and [DISPLAY] simultaneously.
3. It enters the common test mode and displays "COMMON".
4. Each time the [VOLUME] dial is turned, "VOL MIN", "VOL
16", and "VOL MAX" are displayed.
5. To release from this mode, press three buttons of [PLAY
MODE/TUNING MODE], [TUNING + M L], and [DIS-
PLAY] simultaneously.
] button, press the [
] button for more 5
x
Z
] button, press the
x
] button.
?/1
] button.
?/1
] simultaneously.
?/1
]
x
Hide quick links:
Advertisement
Table of Contents
