Advertisement
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN
THE POWER CORD on page 7.) If an extension cord is needed, use only a 3-conductor, 14-
gauge (1mm
2
) cord that is no longer than 1.5 meters.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located at the front of the
treadmill near the power cord. The switch must be
in the on position.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position. (See 1. d. above.)
e. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the
hood and carefully remove the hood. Locate the Reed
Switch (97) and the Magnet (9) on the left side of the
Pulley (10). Turn the Pulley until the Magnet is aligned
with the Reed Switch. Check the gap between the
Magnet and the Reed SwitchÑit should be about 3
mm. If necessary, loosen the Screw (43) and move
the Reed Switch slightly. Retighten the Screw.
Reattach the hood and run the treadmill for a few min-
utes to check for a correct speed reading.
12
c
Tripped
Reset
Tripped
Reset
d
On
Position
3 mm
10
43
97
9
Top
View
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
If further assistance is needed, please call our Customer Service Department at 0345-089009.
1. With the help of a second person, carefully raise the
treadmill to the upright position.
Whilst the other person tips the treadmill to one side
and holds it, insert an Extension Leg (59) into one side
of the Base (32). Make sure that the Extension Leg is
turned so the bracket is on the side shown. Using the
Allen Wrench (102), tighten an Extension Leg Screw
(57) into the Extension Leg and the Base. Attach the
other Extension Leg in the same manner.
2. Refer to HOW TO LOWER THE TREADMILL FOR
USE on page 11. Follow the instructions in step 2 to
lower the treadmill.
Cut the plastic ties holding the cage nuts in the upper
end of each Handrail (60, 62).
Position the Left Handrail (60) on the left Upright (32)
as shown. The bracket on the Extension Leg (59)
should be inside of the lower end of the Left Handrail
(see the inset drawing). Thread two Handrail Bolts (30)
with Handrail Washers (40) into the left Upright and the
Left Handrail. Do not tighten the Handrail Bolts yet.
Whilst another person holds the Console Base (46), at-
tach the Right Handrail (62) in the same way. Be care-
ful to avoid damaging the Wire Harness (35).
, adjustable spanner
, and scissors
1
Bracket
102
57
32
2
46
60
30
30
40
40
30
32
59
59
.
59
35
62
30
5
Advertisement
