Additional Information; Troubleshooting - Pioneer cdj-2000nxs2 Operating Instructions Manual

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below and the [FAQ] for the [CDJ-2000NXS2] on the Pioneer DJ support site.
http://pioneerdj.com/support/
Sometimes the problem may lie in another component. Inspect the other components and electrical appliances being used. If the problem cannot
be rectified, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! This unit may not operate properly due to static electricity or other external influences. In this case, proper operation may be restored by turning the
power off, waiting 1 minute, then turning the power back on.
Problem
Disc cannot be ejected.
Playback does not start when disc
is loaded.
File cannot be played.
No sound is produced, or sound is
distorted or noisy.
Loud noise is produced or playback
stops when a certain disc is played.
File information is not properly
displayed.
Track search operation takes too long.
Back cue function does not work.
Loop play function does not work.
Settings are not stored in the memory. Has the power been turned off directly after
USB device is not recognized.
Cue or loop points are not stored on
storage devices (SD, USB).
Cue points or loop of tracks stored on
a storage device (SD, USB) are not
displayed.
Check
Is [EJECT/LOAD LOCK] set to [LOCK]?
—
Is the disc or file playable?
Is the auto cue function activated?
Is the file copyright-protected (by DRM)?
Are you operating the connected DJ mixer
properly?
Is this unit placed near a TV?
Is the disc scratched?
Is the disc dirty?
Is [LANGUAGE] properly set?
Is the information recorded in a language not sup-
ported by this unit?
Is the auto cue function activated?
—
Is a cue point set?
Is a cue point set?
changing the setting?
Is the USB device properly connected?
Is the USB device connected via a USB hub?
Is the USB device supported by this unit?
Is the file format supported by this unit?
—
Are you trying to store more points than the limit?
Is the storage device (SD, USB) write-protected?
Is there enough free space on the storage device
(SD, USB)?
Was the USB device properly stopped before it
was disconnected the last time?
Remedy
Press the [PLAY/PAUSEf] button to set the pause mode, then press the
[DISC EJECTh] button.
Set [EJECT/LOAD LOCK] at [UTILITY] to [UNLOCK], then press the
[DISC EJECTh] button.
If the [DISC EJECTh] button does not work, insert the pin into the disc force
eject hole to eject the disc.
See Usable media on page 5 .
Press [AUTO CUE] for at least 1 second to turn cancel the auto cue function.
Copyright-protected files cannot be played.
Check the operation of the DJ mixer.
Turn the TV's power off or install this unit and TV away from each other.
Scratched discs may not play.
Wipe the dirt off the disc. (p. 42 )
Set [LANGUAGE] to the proper language.
When creating files using DJ software, etc., record the information in a language
supported by this unit.
Track searching may take some time when there are long silent sections
between tracks.
If track searching is not possible within 10 seconds, a cue point is set at the
beginning of the track.
Set the cue point (p. 23 ).
Set the cue point (p. 23 ).
After changing settings, wait at least 10 seconds before turning the power off.
Connect the device securely (all the way in).
USB hubs cannot be used.
This player supports USB mass storage class devices.
This player supports mobile devices on which rekordbox (iOS/Android) is
installed.
Check the file format of the connected USB device. For the file formats sup-
ported by this unit, see About USB devices on page 6 .
Turn the power off then back on.
The maximum number of cue or loop points that can be stored on storage
devices (SD, USB) per disc is 100. For devices other than discs, the maximum
limit is 10 points per track.
If you try to store more points than the limit, [CUE/LOOP POINT FULL] is dis-
played and the points cannot be stored. In this case, delete some points before
storing new ones.
When an SD memory card is write-protected, [CARD PROTECTED] is displayed
and the points cannot be stored. When a USB device is write-protected,
[USB FULL] is displayed and the points cannot be stored. Disable write-protec-
tion then store the points.
If there is not enough free space on an SD memory card, [CARD FULL] is dis-
played and the points cannot be stored. If there is not enough free space on a
USB device, [USB FULL] is displayed and the points cannot be stored. Free some
space then store the points.
Points may not be displayed if the SD memory card/USB device is removed
without performing the proper stopping procedure or if this unit's power is
turned off.
Check that the SD memory card or USB indicator is not flashing before discon-
necting storage devices (SD, USB) or turning this unit's power off.
39
En