Pin-Belegung Monitor/Remote - Yamaha XH200 Owner's Manual

● XH200
Output Power* 40 Hz–20 kHz
THD+N= 0.1 %
Power Consumption
THD+N
Intermodulation Distortion
Frequency Response
SN Ratio
Half Power, 1 kHz, Att. max, input 600 Ω shunt
Channel Separation
Residual Noise
Input Sensitivity
Voltage Gain
Maximum Input Voltage
Input Impedance
Controls
Connectors
Indicators
Load Protection
Amplifier Protection
Power Supply Protection
Cooling
Power Requirements
Dimensions (W x H x D)
Weight
Included Accessories
* These specifications apply to rated power supplies of 120V, 230V and 240V.
0 dBu=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power)
Specifications and descriptions in this owner's manual are for information pur-
poses only.
Yamaha Corp. reserves the right to change or modify products or specifications
at any time without prior notice. Since specifications, equipment or options may
not be the same in every locale, please check with your Yamaha dealer.
■
MONITOR/REMOTE PIN layout
Pin
No.
XM4180/XM4080
1 GND
2 REMOTE CONTROL STANDBY
3 MONITOR MODEL ID
4 REMOTE CONTROL MUTE CH D
5 MUTE CH C
6 MUTE CH B
7 MUTE CH A
8 MONITOR PROTECT STATUS CH D –
9 PROTECT STATUS CH C PROTECT STATUS CH B
10 PROTECT STATUS CH B –
11 PROTECT STATUS CH A PROTECT STATUS CH A
12 OUTPUT LEVEL CH D
13 OUTPUT LEVEL CH C
14 OUTPUT LEVEL CH B
15 OUTPUT LEVEL CH A
14
XM4180/XM4080/XH200 Owner's Manual
70 V, RL=25 Ω
100 V, RL=50 Ω
Standby
Idle
1/8 (70 V, RL=25 Ω/Pink noise)
40 Hz–20 kHz, Half Power
60 Hz:7 kHz, 4:1, Half Power
Po=1 W, HPF=40 Hz,
80 Hz–20 kHz
(DIN AUDIO)
Att. min, (DIN AUDIO)
Att. max
Att. max
Front Panel
Rear Panel
INPUT
SPEAKERS
MONITOR/REMOTE
POWER/STANDBY
SIGNAL
CLIP/LIMIT
PROTECT/MUTE
Signal
XH200
STANDBY
MODEL ID
–
MUTE CH B
–
MUTE CH A
–
OUTPUT LEVEL CH B
–
OUTPUT LEVEL CH A
MIN
MAX
MAX
MAX
TYP
MIN
MIN
MIN
MAX
TYP
TYP 38 dB (100 V), 35 dB (70 V)
MIN
TYP 20 kΩ (balanced), 10 kΩ (unbalanced)
POWER switch (push on/push off)
attenuator (31 position) x 2
OUTPUT VOLTAGE switch (100 V/70 V) x 1
HPF switch (40 Hz/80 Hz 12 dB/oct) x 2
Euroblock connector (balanced) /ch
POWER switch on/off mute
DC-fault: output relay off/restored automatically.
Clip limiting : THD ≥ 0.5 %
Thermal: Cuts the output (when heatsink temp. ≥ 90 °C);
operation restored automatically.
VI limiter (RL ≤ 16
Thermal: Power supply shutdown (when temp. ≥ 90 °C);
operation not restored automatically.
Variable-speed fan x 1
120V, 220V–240V; 50Hz/60Hz
480 x 88 x 412 mm (18-7/8" x 3-7/16" x 16-1/4")
Power cord, Security cover, Owner's Manual,
3-pin Euroblock connector x 2
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 25A
Conforms to Environments: E1, E2, E3 and E4
Description
STANDBY Control: Supply 5 VDC, 5 mADC
XM4180: 560 Ω, XM4080: 680 Ω, XH200: 820 Ω (Impedance to GND)
MUTE Control: Connect to GND, +5 V, 1 mA
PROTECTION Off/ Output On: +5 VDC, Zo=270 Ω
PROTECTION On/ Output Off: 0 VDC, Zo=High
XM4180, XM4080
+4dBu (-27.2 dB of Speaker Output Level) at 100 W/8Ω, RL=7.5 kΩ, Zo=300 Ω
XH200
-33.2 dB of Speaker Output Level, RL=7.5 kΩ, Zo=300 Ω
200 W x 2
200 W x 2
5 W
40 W
400 W
0.1 %
0.1 %
0 dB
0 dB
-0.5 dB
103 dB
60 dB
-65 dBu
+4 dBu
+22 dBu
Barrier strip/ch
Dsub 15P x 1
x 1 (Green/Orange)
x 2 (Green)
x 2 (Red)
x 1 (Red)
Ω
): Limits the output.
9.8 kg (21.6 lbs)