Table of Contents
Advertisement
end point of the recording data reaches or the media to be
copied becomes full unless the copy is stopped manually (when
"FIFO Overwrite" is set to "Off"). This function is useful for
making backup of the recording data.
Before executing the copy, make sure that the Copy 2
device is connected and set in the <Add/Remove HDD
Device> and <Add/Remove DVD/CD Drive> (System
Menu Memory) correctly.
User Menu
Copy
2
2
Copy Data to Copy 2 Drive
1 + 2
Set Copy 2 Drive
4
1. Set the camera number to be copied.
step
• The button function changes between "All Off"
and "All On" each time you select this button.
You can switch on and off for all the cameras
easily by using this button.
• The picture is not copied when there is no recorded
picture of the set camera number or time.
2. Select "Other settings" and then set the detailed
step
settings.
From Main: Sets the area which contains the data
to be copied. The available setting items are
"Normal," "Alarm," and "LPA."
To Copy 2: Sets the group to where the data is
copied. The available setting items are "SerialBus,"
"NAS," "SCSI," "DVD/CD," and "Internal."
Copy Data: Sets the data area to be copied. The
available setting items are "Alarm" and "All."
Overwrite: Selects whether or not to overwrite the
existed data.
Auto Eject: Selects whether to eject media (CD/
DVD) automatically when the copy is over.
FIFO Overwrite: Selects whether to repeat copying
from the start point of the media by overwriting the
existed data, or to stop copying when the capacity
of the media becomes full during copying. This
setting is available only when the copy destination
is HDD or NAS.
"Alarm" appears for "From Main" when "Alarm Recording
Area" (System Menu
Setting for Main Memory
set to other than "0 %."
"LPA" appears for "From Main" when "Long Pre-Alarm Area"
(System Menu Memory Data Management Setting for
Main Memory Change Partition Setting) is set to other
than "0 %."
When copying the data to DVD while "Overwrite" is set to
"On," the unit clears the existed data of the disc before
overwriting with new data. Note that clearing the data takes
about 30 to 40 minutes. You cannot cancel operation during
clearing the data of the DVD.
When copying the data while "Copy Data" is set to "Alarm,"
the unit performs copy operation, however, the data is not
copied if there is no alarm recording data within the specified
range of copy. In case of CD/DVD disc, the remaining
capacity becomes low because only the management
information is recorded.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Basic operations
Range of Copy
Memory
Data Management
Change Partition Setting) is
Do not use the disc which has been used on the personal
computer, failed to be copied, or stopped during copying
due to the power failure because they may cause
malfunction of the unit.
3. Set the start time of copy.
step
Start: Sets the start point of copy.
Continue: Starts copying from the end point of the
previous copy.
• To set the start point using the bookmark, select
"Bookmark" and then select the desired book
mark number.
• To copy from the oldest recording time, select
4
step
"Copy Start Time."
4. Select "Execute."
step
3
step
• The copy starts.
• To stop copy manually, select "Cancel" in the
screen of <Copy Data to Copy 2 Drive>. The data
1, 2
steps
which has been copied before cancelling is
copied.
The warning is displayed when the copied range exceeds
the available capacity of the device to be copied when
"FIFO Overwrite" is set to "Off" and copy destination is HDD.
In this case, set the copy setting again with narrower copy
range or use a copy device with larger capacity.
When the copy is performed during recording, the picture
of the recording start and end points may not be recorded.
When the recording data of the main device which is being
copied is overwritten or about to be overwritten, copy is
stopped. Be careful for the copy which requires long time
such as overwriting copy of DVD.
The progress bar of copy is not displayed for copy 2.
The picture data is processed in 2 MB unit. Therefore the
data is copied in 2 MB unit from the start point of the
designated range when copying.
Copying the data of this unit to a video
cassette
This function is used to copy the data of this unit to a video
cassette using an analogue video cassette recorder. Data can
be copied even when the unit is in recording. For the recording
operation, see the instruction manual for the analogue video
cassette recorder used.
1. [Analogue video cassette recorder] Prepare the VCR
step
for recording.
• Set the input source of the VCR to the external
input.
2. [This unit] Display the picture in its format (single/
step
split) that you want to record.
3. [This unit] If needed, use the search function to
step
display the start position of copy.
4. [Analogue video cassette recorder] Start recording.
step
5. [This unit] Press the PLAY button to start playback.
step
6. To stop copying, press the STOP button on this unit
step
first. And then, stop the recording on the analogue
video cassette recorder.
Only the picture displayed on the monitor screen can be
copied to the video cassette.
21
Advertisement
Table of Contents
