Industrial mig/mag welding equipment of pulsed-synergic control (104 pages)
Summary of Contents for GALAGAR GALA ELECTRONICS 200 ACDC
Page 1
GALA ELECTRONICS 200 ACDC MANUAL TÉCNICO DE INSTRUCCIONES. EQUIPOS INVERTER DE SOLDADURA AL ARCO. GB TECHNICAL INSTRUCTIONS MANUAL. ARC WELDING INVERTER EQUIPMENT. MANUEL TECHNIQUE D'INSTRUCTIONS. ÉQUIPEMENTS INVERTER DE SOUDAGE À L’ARC. Gala Electronics 200 ACDC Ref. 2200200ACDC ESTE EQUIPO DEBE SER UTILIZADO POR PROFESIONALES.
GALA ELECTRONICS 200 ACDC 1. INTRODUCCIÓN Es un generador de inverter capaz de realizar las siguientes modalidades de soldadura: • • ONTINUO • con corriente pulsada a BAJA frecuencia (TIG pulsado lento) ULSADO • con corriente pulsada a MEDIA frecuencia (TIG pulsado rápido) ULSADO •...
GALA ELECTRONICS 200 ACDC 4. TOMAS DELANTERAS P1: Toma de soldadura NEGATIVO (-). • P2: Toma de soldadura POSITIVO (+). • A2: Conexión frontal gas. Sirve para la • conexión del tubo del gas procedente del soplete. J2: Conector soplete TIG. Es un conector •...
Page 5
GALA ELECTRONICS 200 ACDC S1: Botón selección INTERNO-EXTERNO. Apretando el botón S1 se selecciona efectuar el ajuste de la • corriente de soldadura a través del panel o mediante el mando a distancia ; el led encendido al lado del símbolo confirma la selección.
Page 6
GALA ELECTRONICS 200 ACDC Determina la frecuencia con la cual la corriente de soldadura pasa de DC+ a DC- y viceversa. La siguiente imagen muestra un ejemplo en el cual la onda del segundo gráfico tiene el doble de frecuencia respecto de la primera.
GALA ELECTRONICS 200 ACDC Diámetro electrodo en TIG AC. Indicando al generador el diámetro del electrodo del soplete • L13: que se está utilizando ¡Error! No se encuentra el origen de la referencia. consigue optimizar los parámetros de soldadura en el cebado en TIG AC. Los diámetros disponibles son: 1,0mm – 1,6mm – 2,0mm – 2,4mm – 3,2mm –...
Page 8
GALA ELECTRONICS 200 ACDC Apretar (1T) y mantener apretado el pulsador del soplete. Alzar lentamente el soplete para cebar el arco. La CORRIENTE DE SOLDADURA alcanzará el valor programado realizando eventualmente una RAMPA DE INCREMENTO (tiempo ajustable). Soltar el pulsador (2T) para empezar el procedimiento de acabado de la soldadura.
GALA ELECTRONICS 200 ACDC Las modalidades de soldadura que pueden seleccionarse son: • MMA los valores del HOT-START y del ARC-FORCE están fijados por el constructor y no se pueden regular por medio del panel. • ONTINUO • con corriente pulsada a BAJA frecuencia (TIG pulsado lento) ULSADO •...
GALA ELECTRONICS 200 ACDC 1. INTRODUCTION It is an inverter power source that can carry out the following welding modes: • ONTINUOUS • welding with pulsed current at L frequency (slow pulsed TIG) ULSED • welding with pulsed current at M...
GALA ELECTRONICS 200 ACDC 4. FRONT OUTLETS •P1: NEGATIVE (-) welding socket. •P2: POSITIVE (+) welding socket. •A2: Front gas connector. It is used to connect the gas pipe coming from the torch. •J2: TIG torch. It is a five-pole AMPHENOL connector.
Page 12
GALA ELECTRONICS 200 ACDC S2: WELDING PARAMETERS selection button. • The diagram shows the welding parameters that can be selected clockwise by pressing key S2. Every time the key is pressed a led in the diagram lights up to confirm the dislpay of that parameter on the screen. Once a parameter has been selected, turn the encoder to change its value.
Page 13
GALA ELECTRONICS 200 ACDC Balance value in TIG AC. (Only AC TIG).Displaying of a positive or negative value referring to • L12: the positive wave in the TIG AC mode. A negative value indicates greater penetration and fusion of the electric arc in the weld bath with less cleaning of the piece, while a positive value indicates greater cleaning of the electric arc over the weld bath but with lower penetration.
GALA ELECTRONICS 200 ACDC ELDING ARAMETER EFAULT OTES MMA welding current. Adjustable from front and remote control. TIG welding current. Adjustable from front and remote control. Second welding current in Bi-level Only Bi-level TIG, percentage of the welding current. Adjustable from TIG mode.
GALA ELECTRONICS 200 ACDC The supply of gas continues for a period equal to the POST-GAS time (adjustable). 2t Hf Welding Bring the torch near to the piece to be welded, keeping the point of the electrode 2 or 3 mm away from the piece itself.
GALA ELECTRONICS 200 ACDC MMA mode. The values of both the HOT-START and the ARC-FORCE have been set by the • manufacturer and can not be adjusted through the control panel. ONTINUOUS • welding with pulsed current at L frequency (slow pulsed TIG) ULSED •...
GALA ELECTRONICS 200 ACDC 1. INTRODUCTION Est un générateur de type onduleur qui peut effectuer les types de soudage suivants: • • ONTINU • avec courant pulsé à B fréquence (TIG pulsé lent) ULSE ASSE • avec courant pulsé à M fréquence (TIG pulsé...
GALA ELECTRONICS 200 ACDC 4. PRISES FRONTALES •P1: Prise de soudage NEGATIF (-). •P2: Prise de soudage POSITIF (+). •A2: Robinet du gaz à l’avant. Il sert à raccorder le tuyau de gaz provenant de la torche. •J2: Connecteur pour la torche TIG. C’est un connecteur AMPHENOL à...
Page 19
GALA ELECTRONICS 200 ACDC S1: Touche sélection INTERNE-EXTERNE. Quand vous appuyez sur la touche S1 vous sélectionnez le réglage • du courant de soudage à partir du tableau (INTERNE) ou à partir de la commande à distance (EXTERNE). Le voyant allumé à côté du symbole confirme la sélection.
Page 20
GALA ELECTRONICS 200 ACDC L’image suivante montre l’exemple où l’onde du deuxième graphique a une double fréquence par rapport à la première. Des valeurs élevées de la fréquence d’inversion favorisent une plus grande concentration de l’arc avec une zone thermiquement altérée réduite.
GALA ELECTRONICS 200 ACDC Diamètre de l’électrode au TIG en c.a. Si vous sélectionnez le diamètre de l’électrode de la • L13: torche que vous êtes en train d’utiliser sur le tableau de commande, ¡Error! No se encuentra el origen de la referencia.
Page 22
GALA ELECTRONICS 200 ACDC Soudage 4t À L’arc Souple Touchez la pièce en cours d’usinage avec l’électrode de la torche. Appuyez sur (1T) et relâchez (2T) la gâchette de la torche. Relevez la torche lentement pour amorcer l’arc. Le COURANT DE SOUDAGE ira à la valeur programmée en exécutant une RAMPE D’AUGMENTATION DU COURANT (temps réglable) si besoin est.
GALA ELECTRONICS 200 ACDC Soudage Pointage Tous nos générateurs TIG HF présentent la fonction pointage; régler la machine sur 2T HF, ainsi que le courant final de soudage sur une valeur proche mais non équivalente au courant de soudage, régler la rampe de descente comme le temps de pointage souhaité, puis.
GALA ELECTRONICS 200 ACDC 8. DONNEES TECHNIQUES ¡E ODALE RROR O SE ENCUENTRA EL ORIGEN DE LA REFERENCIA 40°C EMPÉRATURE AMBIANTE 230V~±15%/50-60H ENSION DU RÉSEAU 16A RETARDE ROTECTION DU RÉSEAU ROCESS DE SOUDAGE 100% 100% YCLE DE TRAVAIL 150A 130A...
Page 29
GALA ELECTRONICS 200 ACDC FABRICACIÓN Y VENTA DE APARATOS DE SOLDADURA AUTÓGENA, ELÉCTRICA Y CONSTRUCCIONES ELECTROMECÁNICAS. MANUFACTURE AND SALE OF AUTOGENOUS, AND ELECTRIC WELDING APPLIANCES, AND ELECTROMECHANICAL CONSTRUCTIONS. FABRICATION ET VENTE D’APPAREILS DE SOUDAGE AUTOGÈNE, ÉLECTRIQUE ET CONSTRUCTIONS ÉLECTROMÉCANIQUES. CENTRAL: Jaime Ferrán, 19, nave 30...