Progress Of Programme; Canceling The Programme; Loading Door Lock; Changing The Selections After Programme Has Started - Beko WTE 6531 X0 User Manual

To deactivate the Child Lock:
Press and hold 1st and 2nd auxiliary function buttons
for 3 seconds while any programme is running. The
lights on the 1st and 2nd Auxiliary Function buttons
will flash while you keep the buttons pressed for 3
seconds.
C
In addition to the method above, to deactivate
the Child Lock, switch the Programme Selection
knob to On / Off position when no programme is
running, and select another programme.
C
When the power is restored after a power failure
or after your machine is unplugged and plugged in
again, the Child Lock will not be deactivated when
the machine resumes operating.

4.13 Progress of programme

Progress of a running programme can be followed from
the Programme Follow-up indicator. At the beginning of
every programme step, the relevant indicator light will
turn on and light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme
flow while the programme is running. To do this, the
change you are going to make must be in a step after
the running programme step. If the change is not
compatible, relevant lights will flash for 3 times.
C
If the machine does not pass to the spinning
step, Rinse Hold function might be active or the
automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.

4.14 Loading door lock

There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level
of the water inside. If the level is suitable, Loading Door
light illuminates steadily within 1-2 minutes and the
loading door can be opened.
If the level is unsuitable, Loading Door light turns off
and the loading door cannot be opened. If you are
obliged to open the Loading Door while the Loading
Door light is off, you have to cancel the current
programme; see "Canceling the programme" .
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to
pause mode while a programme is running. The light
of the step which the machine is in starts flashing in
the Programme Follow-up indicator to show that the
machine has been switched to the pause mode.
Also, when the loading door is ready to be opened,
Loading Door light will also illuminate continuously in
addition to the programme step light.
15 / EN
Changing the speed and temperature settings
for auxiliary functions
Depending on the step the programme has reached,
you may cancel or activate the auxiliary functions; see,
"Auxiliary function selection" .
You may also change the speed and temperature
settings; see, "Spin speed selection" and "Temperature
selection" .
C
If no change is allowed, the relevant light will flash
for 3 times.
4.15 Adding or taking out laundry
Press the Start / Pause button to switch the machine
to pause mode. The programme follow-up light of the
relevant step during which the machine was switched
into the pause mode will flash. Wait until the Loading
Door can be opened. Open the Loading Door and add
or take out the laundry. Close the Loading Door. Make
changes in auxiliary functions, temperature and speed
settings if necessary. Press Start / Pause button to start
the machine.

4.16 Canceling the programme

To cancel the programme, turn the Programme
Selection knob to select another programme. Previous
programme will be canceled. End / Cancel light will
flash continuously to notify that the programme has
been canceled.
Your machine will end the programme when you turn
the Programme Selection knob; however, it does not
drain the water inside. When you select and start a
new programme, the newly selected programme will
start depending on the step the previous programme
was canceled in. For example, it may take in additional
water or continue to wash with the water inside.
C
Depending on the step where the programme
was canceled in, you may have to put detergent
and softener again for the programme you have
selected anew.
4.17 Your machine is equipped
with a "Standby Mode"
In case of not starting any programme or waiting
without making any other operation when the machine
is turned on by On/Off button and while it is in selection
step or if no other operation is performed approximately
2 minutes after the programme you selected has come
to an end, your machine will automatically switch to
energy saving mode. Display brightness will decrease.
In case of rotating the Programme Selection knob or
pressing any button, lights will restore to their previous
condition. This is not a fault.
Washing Machine / User's Manual