Messages - Panasonic DMP-BD10A Operating Instructions Manual

Reference
11 Troubleshooting guide / Messages
Other difficulties with playback (continued)
No subtitles.
Angle cannot be changed.
The resume play function does
not work.

Messages

The following messages or service numbers appear on the television or unit's display when something unusual is detected during startup and
use.
On the television
Cannot play.
Cannot play on this unit.
Cannot output Audio with HDMI
because of copyright
protection.
No Disc
$
On the unit's display
F99
§
HDMI ONLY
No PLAY
No READ
§
PLEASE WAIT
U30
("∑" stands for a number.)
§
UNFORMAT
§
UNSUPPORT
U59
U72
U73
H or F
§
The messages are alternately displayed.
RQT8966
28
≥Subtitles are not recorded on the disc.
≥Turn the subtitles on. Set "Subtitle" on the On-screen menu to "On".
≥Angles can only be changed during scenes where different angles are recorded.
≥Memorized positions are canceled when
–press [∫] several times.
–open the disc tray.
–[DVD-A] [CD] [VCD] [MP3]: set to standby mode.
≥You inserted an incompatible disc.
≥You tried to play a non-compatible image.
≥Should you connect equipment that does not support HDCP the audio from the CPPM
copy protected DVD-Audio cannot be output from HDMI AV OUT terminal. Connect the
audio cable of the Audio/Video cable (Red, White), optical digital audio cable or coaxial
cable to the corresponding terminals.
≥The disc may be upside down.
≥The operation is prohibited by the unit or disc.
≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby.
Now press [Í/I] on the main unit again to turn the unit on.
≥Some BD-Video discs can only be output with HDMI.
≥When there is a viewing restriction on a BD-Video or DVD-Video.
≥The disc is dirty or badly scratched. The unit cannot play.
≥Displayed when the unit is started and set to standby mode. This is not a malfunction.
≥The unit is carrying out its recovery process. You cannot operate the unit while "PLEASE
WAIT" is displayed.
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [ENTER] and the indicated number button at the
D same time for more than 2 seconds.
R
≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or DVD-
RW (DVD-Video format).
≥You have inserted a disc the unit cannot play.
≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
≥The HDMI connection acts unusually.
–The connected equipment is not HDMI compatible.
–Please use HDMI cables that have the HDMI logo (as shown on the cover).
–The HDMI cable is damaged.
≥There is something unusual. (The service number displayed after H and F depends on the
unit's condition.)
≥Check the unit using the troubleshooting guide. If the service number does not disappear,
do the following.
1. Disconnect the plug from the household mains socket, wait a few seconds, then
reconnect it.
2. Press [Í/I] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request service from
the dealer. Inform the dealer of the service number when requesting service.
Page
—
19
—
—
Page
4, 5
5
8–10
—
—
—
—
21
—
—
—
11
—
4, 5
—
—
—
25–28